รุ่นเต็ม: PNOZ s7 C 24VDC 4 เลขที่ 1 ไม่มี
Pilz PNOZsigma Series รีเลย์ความปลอดภัย
ข้อมูลจำเพาะพื้นฐาน
หมายเลขคำสั่งซื้อ: 750330
จัดหา: 24 ในดีซี
ผู้ติดต่อด้านความปลอดภัย: 4 เปิดตามปกติ (เลขที่)
ติดต่อเสริม: 1 ปกติปิด (ไม่มี)
ความกว้าง: 22.5 มม
การทำงาน: For safety emergency stop, การตรวจสอบประตูนิรภัย, two-hand control and other safety circuit evaluation
ชุด: PNOZ s7 C (C = with cascade interface, for connecting extension modules)
การรับรอง: ซีอี, แอล, ตูฟ; Safety Level PL e/SIL 3 (Compliant with ISO 13849-1/IEC 62061)
การใช้งานทั่วไป
Emergency stop button circuit monitoring
สวิตช์ประตูนิรภัย, สวิตช์จำกัดความปลอดภัย
Small automation machines, เครื่องมือกล, packaging machinery safety control
Can be cascaded with PNOZsigma extension modules (s0, s1, s2, ส4, s5, s6, s7, s8, s9) สำหรับการขยายหน้าสัมผัส
Confusing Model Comparison
750107: PNOZ s7 (without C, no cascade function)
750330: PNOZ s7 C (cascade-capable version)
หมายเหตุการเดินสายไฟ
- เอส11/เอส12: Safety Input Channel 1
- เอส21/เอส22: Safety Input Channel 2 (Dual-channel monitoring)
- 13/14, 23/24, 33/34, 43/44: Four safety normally open outputs
- 51/52: Auxiliary normally closed feedback contact
- UB/0V: 24แหล่งจ่ายไฟวีดีซี
การอ้างอิงทดแทน
การเปลี่ยนชุดเดียวกัน: Original product is preferred for the same specification; domestic safety relays can be used for functional replacement (PL level, contact configuration and wiring logic must be verified)
อัพเกรด: If more contacts are required, cascade with PNOZ s extension modules
ข้อมูลเพิ่มเติม
ระดับการป้องกัน: IP20 (การติดตั้งราง DIN, สำหรับการติดตั้งตู้เท่านั้น)
การติดตั้ง: ราง DIN 35 มม
อุณหภูมิในการทำงาน: -10 ℃~ +55 ℃
เห็ด 750330 (PNOZ s7 C) คำแนะนำการเดินสายไฟ + รายการตรวจสอบการแก้ไขปัญหา
Important Precaution: PNOZ s7 C is a contact extension module. It cannot be used as a standalone master module. It must be used with PNOZsigma master safety relays (s1/s2/s4/s5/s6 etc.); C = cascade connector, connected to master module via U-link. It is NOT an independent evaluation unit.
- นิยามเทอร์มินัล
A1: 24VDC+
A2: 24กระแสตรง-
ผลลัพธ์ด้านความปลอดภัย (Force-guided normally open, สำหรับวงจรความปลอดภัย)
13-14, 23-24, 33-34, 43-44 (4 sets n/o)
ติดต่อเสริม (Not allowed for safety cut-off circuits, only for PLC feedback/indicator lamps)
51-52 (1 set n/c)
Top side: Cascade slot + Terminator plug
- Two Wiring Schemes
โครงการ 1: Cascade with PNOZsigma Master Module (ที่แนะนำ, with pulse detection)
- Mount master module and s7 C side by side on DIN rail, remove terminator plugs on both modules
- Insert PNOZsigma U-link connector; internal safety signals are transmitted from master module to s7C
- Master module is powered at A1/A2; s7C A1/A2 also requires separate 24V DC supply
- Route outputs 13-14/23-24/33-34/43-44 into contactor coil circuits; a 6A fuse is recommended to prevent contact welding
- 51-52 is wired to PLC digital input for status feedback
Cascade Rule: The terminator plug must be fitted on the LAST module of the cascade chain! Fault will be triggered if missing.
โครงการ 2: Hardwired extension for non-sigma series (PNOZ X etc., no U-link)
The safety output contact of the master relay is wired into the s7 C supply loop (master safety contact acts as enable for s7C power supply)
Master contact closed → s7C energized, all safety outputs closed
Master contact open → s7C de-energized, all safety outputs open
⚠️ No internal short-circuit pulse diagnosis in this mode. Safety architecture is downgraded, only for low-risk applications.
- Safety Wiring Rules
- สูงสุด. load for safety outputs: ≤6A, 240VAC; fuses are mandatory to avoid contact welding
- 51-52 auxiliary contact must not be used for safety cut-off, only for status signals
- เคเบิล: Copper wire with ferrule for cabinet wiring, ขั้วสปริง; IP20, no exposed wiring
- Emergency stop/safety gate logic is fully configured on the PNOZsigma master module (mode selector, dual-channel detection, รีเซ็ตอัตโนมัติ/ด้วยตนเอง). s7C only follows the output state
- Check U-link connection regularly for vibration-prone applications (เครื่องมือกล, สายพานลำเลียง)
- คำจำกัดความของตัวบ่งชี้ LED (PNOZ s7C itself)
POWER: 24V supply present
ออก: Safety outputs closed (master module permits output)
ความผิดพลาด: Diagnostic error/fault lockout
IN1, IN2 indicators are located on the master module. The s7C extension module has no input indicators.
- รายการตรวจสอบการแก้ไขปัญหา (ตามลำดับ)
ความผิดพลาด 1: FAULT LED ON continuously, ไม่มีเอาต์พุต (most frequent)
สาเหตุ 1: Terminator plug missing or not installed on the last module
การเยียวยา: ปิดเครื่อง, fit terminator plug on the last module’s cascade slot, power on and reset
สาเหตุ 2: U-link loose or not fully clipped
การเยียวยา: ปิดเครื่อง, re-seat U-link and confirm locking
สาเหตุ 3: No supply/reversed polarity/excessive voltage drop on A1/A2
การเยียวยา: Measure A1-A2 voltage with multimeter, confirm stable 24VDC; check spring terminal loose connections
สาเหตุ 4: Master module FAULT, wrong mode setting, short circuit on master input channels
การเยียวยา: Troubleshoot master module first; s7C will only work normally once master is recovered
ความผิดพลาด 2: POWER LED ON, OUT LED OFF, FAULT LED OFF
สาเหตุ 1: Master safety relay is in safe-off state (E-stop pressed, safety gate open)
การเยียวยา: Reset E-stop/close safety gate, confirm master OUT LED lights up
สาเหตุ 2: Master module set to manual reset and reset button not pressed
สาเหตุ 3: Wrong cascade order; master module is not the first unit in chain
สาเหตุ 4 (hardwired mode): Master safety contact damaged/open circuit
ความผิดพลาด 3: Intermittent FAULT trigger, output flickering
สาเหตุ 1: U-link loose due to cabinet vibration (เครื่องมือกล, สายลำเลียง)
สาเหตุ 2: High ripple/insufficient capacity/frequent dip on 24V power supply
สาเหตุ 3: Short circuit on output circuit, fuse blown and safety lockout activated
สาเหตุ 4: Cross-wire/earth short circuit on master module input wiring (pulse detection triggers fault)
ความผิดพลาด 4: FAULT latched, cannot reset after power cycle
สาเหตุ: Internal safety contact welding (overload/short circuit without fuse protection)
การเยียวยา: Module cannot be repaired; แทนที่โดยตรง. Add fuses on output circuits to prevent recurrence.
ความผิดพลาด 5: Master module normal, s7C output out of sync
สาเหตุ: Poor U-link contact; or welded contact on intermediate contactor in hardwired configuration
- Standard Commissioning Procedure
- ปิดเครื่อง, mount on DIN rail, wire power supply, fit U-link and terminator plug
- Wire master module and set mode selector (adjust selector only when power OFF; changing under power will lock fault)
- Verify fuses on all safety output loops
- เปิดเครื่อง. Master IN1/IN2 OK, master OUT ON → s7C POWER + OUT ON
- การทดสอบฟังก์ชัน: Trigger E-stop/open gate → master OUT OFF, s7C OUT opens synchronously; reset and confirm synchronous closing
- บันทึก: Safety function verification must be performed after every wiring change or module replacement
- Quick Comparison: s7 (750107) vs s7 C (750330)
750107: PNOZ s7, ส่วนขยาย, no C, U-link cascade not supported
750330: PNOZ s7 C, ส่วนขยาย, C version, U-link cascade supported (โมเดลของคุณ)
Working Principle of PILZ 750330 (PNOZ s7 C)
สรุปหลัก: It has no input channels and no safety logic evaluation function. It is a follower-type extension module equipped with force-guided safety contacts. Safety judgement, dual-channel detection and short-circuit pulse diagnosis are all performed by the upstream PNOZsigma master module. The s7 C only synchronously follows the master safety command and feeds back its actual contact status to the master for verification.
สำคัญ: PL e/SIL3 safety rating is determined by the master module. s7 C alone cannot raise the safety level.
- Internal Hardware Structure
ภายใน: Two independent safety relays with mechanically linked force-guided contacts, 4 safety normally open outputs + 1 auxiliary normally closed feedback contact
แหล่งจ่ายไฟ: Independent 24VDC supply on A1/A2 (not powered by master module)
Top U-link port: Dual-channel drive signals + feedback return line, safety link; not ordinary communication bus
Terminator plug: Closing component for the end of cascade chain, used by master module to confirm chain integrity; fault is triggered if removed
- Standard Cascade Mode (U-link connection, recommended dual-channel safety architecture)
- Master module (s1/s2/s4/s5/s6 etc.) collects E-stop and safety gate signals, performs dual-channel comparison, cross-line short-circuit pulse detection and reset logic
- When safety conditions are satisfied, master sends synchronized dual-channel drive signals to s7 C via U-link
- s7 C receives valid drive signals → internal two safety relays pull in simultaneously, 13-14, 23-24, 33-34, 43-44 four safety contacts close
- Critical safety closed-loop: The actual contact state of s7 C is sent back to master module via cascade lines
Master continuously compares: issued command vs real feedback contact status
Matched: การทำงานปกติ
Mismatched (การเชื่อมแบบสัมผัส, failure to act, ลวดขาด, loose U-link): Master cuts drive immediately, whole safety chain locks FAULT, safety contacts force open
- Once safety trip condition occurs (E-stop pressed, ประตูนิรภัยเปิดออก): Master stops drive signal → s7C relays de-energize, all safety contacts open; status feedback is sent back to master for verification
This bidirectional verification is the core of force-guided contact + feedback monitoring, preventing dangerous failure mode where contacts remain conductive after open command due to welding.
- Hardwired Mode (without U-link, downgraded single-channel)
Master safety output contact is wired into s7C supply enable loop:
Master contact closed → s7C energized, outputs closed
Master contact open → s7C de-energized, เอาท์พุทเปิดอยู่
⚠️ Defect: No dual-channel feedback. Master cannot diagnose internal faults of s7C. Safety architecture no longer meets PL e, only for low-risk applications.
- LED Logic
POWER: A1/A2 24V supply OK
ออก: Valid drive signal received from master, safety contacts closed
ความผิดพลาด: Master detects chain anomaly (loose U-link, missing terminator, inconsistent feedback, broken cascade line), safety lockout activated
- Diagnosis Principle (Why missing terminator triggers FAULT)
The whole cascade chain forms a serial closed diagnostic loop: Master → s7C1 → s7C2 → … → terminator plug on last module.
Master continuously sends diagnostic pulses scanning the whole chain. The terminator acts as an end termination resistor to close the pulse circuit.
Plug removed → pulse circuit open → master detects broken chain and locks FAULT to prevent uncontrolled extension module behaviour.
- Function Division: Master vs s7 C
โมดูลหลัก:
Connect E-stop/safety gate inputs
Dual-channel detection, cross-wire short-circuit detection, reset logic
Send drive commands + receive feedback and fault judgement from all extension modules
PNOZ s7 C (750330):
No input terminals, cannot connect E-stop
การกระทำ: Pull in/open safety contacts synchronously
Feed back real contact status continuously to master for verification
Only increases available safety contacts, no safety logic evaluation
- Core Safety Design
Internal relays adopt mechanical force-guided structure: If one relay contact welds closed, the mechanical coupling ensures the other contact opens reliably. This anomaly is fed back to master and triggers fault lockout, avoiding dangerous “command open but contact conductive” failure.
Pilz PNOZ Safety Relay Order List
บันทึก: PNOZsigma (750xxx/751xxx) is current mainstream series; พีนอซ เอ็กซ์ (774xxx /777xxx /787xxx) is legacy classic series; PNOZmulti2 is programmable safety controller. s7 C (750330) is sigma contact extension module and cannot be used standalone.
คำย่อ: n/o=normally open, n/c=normally closed, n/o t=delayed-off normally open, SC=semi-conductor output
- PNOZsigma Series (24กระแสตรง, ที่ต้องการ, พีแอล อี/SIL3)
Standalone Master Modules (can work alone for E-stop/safety gate)
| หมายเลขคำสั่งซื้อ. | รุ่นเต็ม | ติดต่อข้อมูลจำเพาะ | ความกว้าง | หมายเหตุ |
| 750101 | PNOZ s1 24VDC 2n/o | 2เลขที่ | 12.5มม | ช่องเดียว, ขั้นพื้นฐาน |
| 750102 | PNOZ s2 24VDC 3n/o 1n/c | 3NO+1NC | 17.5มม | ช่องเดียว |
| 750103 | PNOZ s3 24VDC 2n/o | 2เลขที่ | 17.5มม | Dual-channel short-circuit detection |
| 751103 | PNOZ s3 C 24VDC 2n/o | 2เลขที่ | 17.5มม | Cascade C version |
| 750104 | PNOZ s4 24VDC 3n/o 1n/c | 3NO+1NC | 22.5มม | สองช่องทาง, ใช้กันอย่างแพร่หลาย |
| 750105 | PNOZ s5 24VDC 2n/o 2n/o t | 2NO+2 delayed NO | 22.5มม | Delay-off type |
| 750106 | PNOZ s6 24VDC 3n/o 1n/c | 3NO+1NC | 22.5มม | Two-hand control dedicated |
| 750107 | PNOZ s7 24VDC 4n/o 1n/c | 4NO+1NC | 22.5มม | ส่วนขยาย, no U-link cascade |
| 750330 | PNOZ s7 C 24VDC 4n/o 1n/c | 4NO+1NC | 22.5มม | Cascade C version, U-link compatible (โมเดลของคุณ) |
| 750108 | PNOZ s8 24VDC 2n/o | 2เลขที่ | 12.5มม | Small contact extension |
| 750109 | PNOZ s9 24VDC 3n/o | 3เลขที่ | 17.5มม | Contact extension |
| 750110 | PNOZ s10 24VDC 2n/o | 2เลขที่ | 12.5มม | Dual-channel light curtain |
| 750111 | PNOZ s11 24VDC 4n/o | 4เลขที่ | 22.5มม | สองช่องทาง |
| 750124 | PNOZ s4.1 24VDC | 3NO+1NC | 22.5มม | Special reset mode |
| 750126 | PNOZ s6.1 24VDC | 3NO+1NC | 22.5มม | Improved two-hand control |
| 750150 | PNOZ s20 24VDC | Semi-conductor output | 12.5มม | Pure semiconductor |
| 750151 | PNOZ s22 24VDC | Semi-conductor output | 17.5มม | Light curtain dedicated |
| 750130 | PNOZ s30 24VDC | 2NO+2 delayed NO | 22.5มม | ล่าช้านาน |
| 750152 | PNOZ s50 24VDC | Semi-conductor | 22.5มม | Semi-conductor safety output |
Sigma Accessories
| หมายเลขคำสั่งซื้อ. | คำอธิบาย |
| 750008 | PNOZsigma U-link Cascade Connector |
| 750009 | Terminator Plug (mandatory at end of chain) |
- PNOZ X Legacy Series (เอซี/ดีซีสากล, for replacement of existing projects)
Basic E-stop/Safety Gate Models
| หมายเลขคำสั่งซื้อ. | แบบอย่าง | รายชื่อผู้ติดต่อ | จัดหา |
| 777303 | พีนอซ X2P | 2เลขที่ | 24VAC/ดีซี |
| 787059 | PNOZ X7P C | 2เลขที่ | 24VAC/ดีซี |
| 774053 | พีนอซ X7 | 2เลขที่ | 110VAC |
| 774055 | พีนอซ X7 | 2เลขที่ | 120VAC |
| 774057 | พีนอซ X7 | 2เลขที่ | 240VAC |
| 787100 | PNOZ X1P C | 3NO+1NC | 24กระแสตรง |
| 787310 | PNOZ X3P C | 3NO+1NC | 24VAC/ดีซี |
| 774729 | พีนอซ X6 | 3เลขที่ | 24VAC/ดีซี |
| 774080 | พโนซิส 11 | 7NO+1NC | 24VAC/ดีซี |
| 774006 | พโนซิส 10 | 6โน+4เอ็นซี | 230-240VAC |
Delay-off XV Series
| หมายเลขคำสั่งซื้อ. | แบบอย่าง | รายชื่อผู้ติดต่อ | ช่วงหน่วงเวลา |
| 777510 | PNOZ XV3P 30 | 3NO+2 delayed NO | 0.1~30วิ |
| 774610 | PNOZ XV3.1 30 | 3NO+1NC+2 delayed NO | 0.1~30วิ |
| 774618 | PNOZ XV3.1 300 | 3NO+1NC+2 delayed NO | 0.3~300s |
Two-hand Control P2HZ Series
| หมายเลขคำสั่งซื้อ. | แบบอย่าง | รายชื่อผู้ติดต่อ |
| 777340 | P2HZ X1P | 3NO+1NC+2SC |
| 774350 | P2HZ X3 | 2NO+1NC |
| 774360 | P1HZ X1 | 2เลขที่ |
Contact Extension PZE Series (for PNOZ X master)
| หมายเลขคำสั่งซื้อ. | แบบอย่าง | รายชื่อผู้ติดต่อ |
| 774580 | PZE X4 | 4เลขที่ |
| 777580 | PZE X4P | 4เลขที่ |
| 774590 | PZE X5 | 5เลขที่ |
| 777600 | PZE 9P | 7โน+2เอ็นซี |
- PNOZมัลติ 2 Programmable Safety Controllers (Large machines, multi safety functions)
| หมายเลขคำสั่งซื้อ. | แบบอย่าง | คำอธิบาย |
| 772100 | PNOZ ฉัน B0 | หน่วยฐาน, ขยายได้ |
| 772104 | PNOZ ฉัน B0.1 | B0 upgraded version |
| 772105 | PNOZ ม C0 | กะทัดรัด, non-expandable |
| 772138 | PNOZ m ES ETH | โมดูลการสื่อสารอีเทอร์เน็ต |
- คู่มือการเลือกฉบับย่อ
- 750xxx = PNOZsigma new series; 750xxx without C = standalone/hardwired extension; 751xxx /7503xx with C = U-link cascade supported
- 774/777/787xxx = PNOZ X legacy series, for spare replacement only, ไม่แนะนำสำหรับโครงการใหม่
- 772xxx = PNOZmulti2 programmable safety controller (not simple safety relay)
- s7 (750107) and s7C (750330) are both extension modules, cannot connect E-stop independently, must pair with sigma master
- Confusing Model Reference
750107: PNOZ s7, ส่วนขยาย, no C, U-link cascade not supported
750330: PNOZ s7 C, ส่วนขยาย, C version, U-link cascade supported
คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง



















NH42-63-318x560.png)



