ตึงเครียด DGK-04F Voltage Monitoring Relay - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

ตึงเครียด DGK-04F Voltage Monitoring Relay - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

บมจ/

ตึงเครียด DGK-04F Voltage Monitoring Relay

ยี่ห้อ: ตึงเครียด (ไก่งวง) ผลิตภัณฑ์: 3-Phase Digital Adjustable Overvoltage / แรงดันตก & รีเลย์ป้องกันลำดับเฟส (รีเลย์ตรวจสอบแรงดันไฟฟ้า) Model Code Explanation DGK: Series of 3-phase digital voltage control relays 04: Function code → Overvoltage + แรงดันตก + Phase Sequence Monitoring F: รุ่นจอแสดงผลดิจิตอล (enhanced model) Sibling model: ดีจีเค-04PF with extra phase loss protection Protection ...

  • รายละเอียดสินค้า

ยี่ห้อ: ตึงเครียด (ไก่งวง)

ผลิตภัณฑ์: 3-Phase Digital Adjustable Overvoltage / แรงดันตก & การป้องกันลำดับเฟส รีเลย์ (รีเลย์ตรวจสอบแรงดันไฟฟ้า)

  1. คำอธิบายรหัสรุ่น

ดีจีเค: Series of 3-phase digital voltage control relays

04: Function code → Overvoltage + แรงดันตก + Phase Sequence Monitoring

เอฟ: รุ่นจอแสดงผลดิจิตอล (enhanced model)

Sibling model: ดีจีเค-04PF with extra phase loss protection

  1. ฟังก์ชั่นการป้องกัน
  2. 3-phase overvoltage protection (คุณ>)
  3. 3-phase undervoltage protection (คุณ<)
  4. ลำดับเฟส / reverse phase protection (phase sequence detection cannot be turned off on DGK-04เอฟ)
  5. Real-time digital display of 3-phase line voltages + fault LED indication
  6. ข้อมูลจำเพาะทางเทคนิค

แหล่งจ่ายไฟ & การวัด: 3-phase AC380V, no neutral required, L1/L2/L3 only

ความถี่: 50/60Hz auto-adaptive

Undervoltage setting range: 230~360V AC

Overvoltage setting range: 400~460V AC

เวลาหน่วงเวลาเกิดข้อผิดพลาด: 0.1~10s adjustable

หน้าสัมผัสเอาต์พุต: 1NO+1NC (สปดีที), 5ก / 250V AC resistive load

การติดตั้ง: การติดตั้งราง DIN มาตรฐาน

อุณหภูมิในการทำงาน: -10℃ ~ +55 ℃

ความแม่นยำในการวัด: ±1V

  1. นิยามเทอร์มินัล

L1, L2, L3: 3-phase voltage input

1, 2, 3: Relay changeover contacts

เทอร์มินัล 1: เอ็นซี (ปกติปิด)

เทอร์มินัล 2: คอม (ทั่วไป)

เทอร์มินัล 3: เลขที่ (เปิดตามปกติ)

สายไฟมาตรฐาน (มอเตอร์ / Air Compressor / ปั๊มน้ำ)

Contactor coil circuit: Wire in series with 2-3 (เลขที่)

Alarm lamp / Buzzer: เชื่อมต่อไปยัง 1-2 (เอ็นซี)

Safety note: L1/L2/L3 must be from the same 3-phase power source; do not mix phases from different circuits.

  1. สายไฟ & คู่มือการว่าจ้าง

Panel Buttons & ตัวชี้วัด

คุณ: Overvoltage setting key

คุณ< : Undervoltage setting key

ที : Time delay setting key

จอแสดงผลดิจิตอล: Cyclically shows L1-L2 / L2-L3 / L3-L1 line voltages

ออก: Relay output indicator (เปิดภายใต้สภาวะปกติ)

คุณ: Overvoltage fault LED

คุณ< : Undervoltage fault LED

PHASE: Phase sequence error LED

Power-on logic: The unit shows parameter settings for 2 seconds first, then automatically cycles through 3-phase voltage readings.

Pre-power Check (บังคับ)

  1. Perform all wiring with power disconnected; confirm no short circuit on L1/L2/L3.
  2. Contact load limit: Max 5A/250VAC; only interlock the control circuit, do not switch main power of large contactors directly.
  3. Keep away from inverters and large contactors to avoid strong electromagnetic interference.

Step-by-step Commissioning

ขั้นตอน 1: เปิดเครื่อง

Switch on 3-phase supply, digital display lights up:

OUT ON: แรงดันไฟฟ้า & phase sequence normal, relay energized, 2-3 ปิด.

PHASE ON: Phase sequence reversed → Power off and swap any two incoming phases (L1↔L2 or L2↔L3).

U/ U< บน: Voltage exceeds threshold, protection activated.

ขั้นตอน 2: Set Undervoltage U< (ที่แนะนำ: 340V for 380V systems)

  1. Short press the U< key to enter undervoltage setup.
  2. Press U< to increase value; press t to decrease value.
  3. รอ 4 seconds without operation to auto-save and return to voltage monitoring screen.

Setting range: 230~360V

ขั้นตอน 3: Set Overvoltage U(ที่แนะนำ: 420V for 380V systems)

  1. Short press the Ukey to enter overvoltage setup.
  2. Press Uto increase value; press t to decrease value.
  3. Auto-save after 4 seconds idle.

Setting range: 400~460V

ขั้นตอน 4: Set Fault Time Delay t (Recommended 1~3s to avoid false tripping from momentary voltage dips)

  1. Short press the t key to enter delay setup.
  2. U= increase time; คุณ< = reduce time.
  3. Settings take effect after auto-save.

พิสัย: 0.1~10วิ; same delay applies for fault trip AND automatic reset after voltage recovers.

ขั้นตอน 5: Phase Sequence Function Note

ดีจีเค-04เอฟ: Phase sequence detection cannot be disabled. Reverse phase will trigger protection, PHASE LED lights up, OUT turns off, and contact 2-3 เปิด.

If phase sequence monitoring is not required (fans without rotation direction requirement), you need to select another model. Only DGK-04PF adds phase loss protection.

ขั้นตอน 6: Functional Test

  1. สถานะปกติ: OUT stays ON, 2-3 ปิด, contactor can energize.
  2. Simulate overvoltage: Raise supply voltage or lower the Uthreshold; ULED lights up, OUT cuts off, 2-3 เปิด.
  3. Simulate undervoltage: Lower supply voltage or raise the U< เกณฑ์; คุณ< LED lights up, รีเลย์ไม่ทำงาน.
  4. Swap two phases: PHASE fault triggers, relay drops out.

ฮิสเทรีซีส: Relay only restores after voltage returns within the set window (+5V tolerance) plus the programmed time delay.

Recommended Parameters (AC380V 3-phase Equipment)

Undervoltage U<: 340วี

Overvoltage U>: 420วี

Time delay t: 2ส

Troubleshooting List

  1. PHASE LED always ON after power-up: Phase sequence reversed; swap any two incoming phases.
  2. OUT OFF with no fault indication: One phase is missing; measure line voltages on L1/L2/L3.
  3. การสะดุดที่ผิดพลาดบ่อยครั้ง: Increase time delay t; check for grid voltage flicker or loose terminal connections.
  4. Flashing reading on one phase: Abnormal voltage on that phase.
  5. Voltage reading normal but relay will not energize: Check continuity of terminals 2-3 and the contactor control circuit.

ข้อห้ามอันเข้มงวด

❌ Never connect L1/L2/L3 to the output terminals of an inverter (distorted sine wave will cause false fault alarms).

❌ Do not feed single-phase 220V power into L1/L2/L3.

❌ Do not use the relay contacts to drive high-power loads directly; only use them for control circuit interlock.

Time Delay (ที) Setting for TENSE DGK-04เอฟ

ช่วงหน่วงเวลา: 0.1~10 seconds. This single setting covers both fault confirmation delay AND voltage recovery reset delay. The relay will only re-energize after the voltage returns to normal and the set time elapses.

ขั้นตอนการดำเนินงาน

  1. While the display is cycling through line voltages, short press the t key to enter delay setup; the digital tube shows the current time value.
  2. Press U= increase time value
  3. Press U< = decrease time value
  4. Stop pressing any key; wait approx. 4 seconds for auto-save, then the unit returns to voltage monitoring mode automatically.

✅ Factory recommended setting: 1~2s to filter short grid transients and prevent false tripping.

เครื่องอัดอากาศ & ปั๊มน้ำ: 2s preferred

Fast cut-off protection requirement: set to 0.5s

Key Logic

เมื่อเกิดแรงดันไฟฟ้าเกิน / แรงดันตก / reverse phase occurs: รีเลย์เริ่มจับเวลา; contacts only open after the delay expires.

When the fault clears and voltage recovers (with +5V hysteresis): The relay waits the same t seconds before closing contacts again.

Phase sequence faults also follow this same time delay setting.

ปัญหาทั่วไป

New setting not saved: Do not press any confirm key; just wait for automatic return. Avoid long key presses.

Unwanted frequent tripping: Increase the t value.

Slow recovery after fault: Reduce the t value appropriately.

Full Model List of TENSE (ไก่งวง) DGK Digital Voltage Monitoring Relays

DGK series: Digital readout, adjustable over/undervoltage, การติดตั้งราง DIN, no neutral required (L1/L2/L3 line voltage detection).

Suffix definition: F = digital display; P = phase loss protection added

แบบอย่างเฟสฟังก์ชั่นหลักหมายเหตุ
ดีจีเค-01เฟสเดียวAdjustable overvoltage + แรงดันตก, จอแสดงผลดิจิตอลAC220V single-phase monitoring
ดีจีเค-033-เฟสปรับแรงดันไฟฟ้าเกิน/ตกได้, no phase sequence check, จอแสดงผลดิจิตอลFor loads with no rotation direction requirement
ดีจีเค-043-เฟสปรับแรงดันไฟฟ้าเกิน/ตกได้, no phase sequence, analog knob (ไม่มีจอแสดงผล)Analog version without digital readout
ดีจีเค-04เอฟ3-เฟสแรงดันไฟฟ้าเกิน + แรงดันตก + ลำดับเฟส, จอแสดงผลดิจิตอลรุ่นปัจจุบันของคุณ; no phase loss protection, phase sequence check cannot be disabled
ดีจีเค-04พีเอฟ3-เฟสแรงดันไฟฟ้าเกิน + แรงดันตก + ลำดับเฟส + การสูญเสียเฟส, จอแสดงผลดิจิตอลUpgraded model of DGK-04เอฟ, widely used on air compressors & ชิลเลอร์

Analog Knob Series (GK Series, No Digital Display)

แบบอย่างการทำงาน
GK-033-phase over/undervoltage adjustable, no phase sequence
GK-043-phase over/undervoltage adjustable, no phase sequence
GK-04เอฟ3-phase over/undervoltage + ลำดับเฟส

ลำดับเฟส / การสูญเสียเฟส / Unbalance Protection Series (เอฟเค / FKV Series, without continuous voltage adjustment window)

These models focus on phase loss, 3-phase unbalance and phase sequence; some support PTC motor temperature protection, not the DGK over/undervoltage main series.

เอฟเค-04: การสูญเสียเฟส + ลำดับเฟส, ที่ตายตัว 30% unbalance threshold

เอฟเค-05 / เอฟเค-05เอฟ: การสูญเสียเฟส + ลำดับเฟส, unbalance adjustable 5~25% (F = digital display)

FK-14 / FK-14P: ลำดับเฟส + การสูญเสียเฟส; P model with PTC motor thermal protection

เอฟเคเอ็ม-05 / เอฟเคเอ็ม-05เอฟ: Adjustable unbalance, ลำดับเฟส, การสูญเสียเฟส

FKT-06 / FKT-06พีเอฟ: 3-เฟสไม่สมดุล + การสูญเสียเฟส + ลำดับเฟส; PF with PTC input

FKV-03 / FKV-03เอฟ / FKV-03ดีเอฟ / FKV-03เอชเอฟ: การสูญเสียเฟส, ลำดับเฟส, ไม่สมดุล; some versions require neutral N

FKV-14 / FKV-14P: Economy phase sequence & รีเลย์การสูญเสียเฟส; P with PTC protection

Suffix Quick Reference

เอฟ: Digital display type

ป: Phase loss protection function

ต: Built-in PTC motor temperature protection

DF/HF: Adjustable unbalance ratio

เอ็น: Requires neutral wire (3พี+เอ็น)

คู่มือการเลือกฉบับย่อ (Most Popular Engineering Models)

  1. Only over/undervoltage monitoring, no rotation check: ดีจีเค-03
  2. Over/undervoltage + anti-reverse phase (motor rotation control): ดีจีเค-04เอฟ
  3. Over/undervoltage + anti-reverse phase + การป้องกันการสูญเสียเฟส: ดีจีเค-04พีเอฟ (first choice for air compressors & เครื่องทำน้ำเย็น)
  4. Only phase loss & unbalance monitoring without voltage threshold adjustment: เอฟเค-05เอฟ / FKV-14

Common Specifications for All DGK 3-phase Models

เอาท์พุต: 1NO+1NC SPDT contact, 5มี/250VAC

Time delay: 0.1ปรับได้ประมาณ 10 วินาที (shared trip & reset delay)

ช่วงแรงดันไฟฟ้า: Undervoltage 230~360V; Overvoltage 400~460V (for 380V line voltage systems)

พลัง & measurement input: L1/L2/L3 only, no neutral wire needed

ก่อนหน้า:

ทิ้งคำตอบไว้

ฝากข้อความ