Ordering No.: 1SFA898216R7000
بي اس تي اكس: ايه بي بي PSTX advanced بداية ناعمة مسلسل, three-phase thyristor control with built-in bypass contactor
470: تصنيف التشغيل الحالي (In-line connection): 470 أ
690: جهد الدائرة الرئيسية: 208~690 VAC
70: التحكم في العرض: 100–250 V AC, 50/60 هرتز
- Key Technical Ratings
| غرض | مواصفة |
| In-line rated current | 470 أ |
| Inside-delta equivalent current | 814 أ |
| جهد الدائرة الرئيسية | 208~690 VAC, 50/60 هرتز |
| التحكم في العرض | 100–250 VAC |
| قوة (In-line, 400V) | 250 كيلوواط |
| قوة (In-line, 690V) | 450 كيلوواط |
| قوة (Inside-delta, 690V) | 800 كيلوواط |
| Starting capacity | 4×Ie for 10 secondseero |
| Maximum starts per hour | 6 timeseero |
| تبريد | Thermostat-controlled fan cooling, built-in bypass contactoreero |
| فئة الحماية (الدائرة الرئيسية) | IP20; detachable keypad IP66eero |
| تواصل | Built-in Modbus RTUeero |
| الإخراج التناظري | حاضِر / الجهد االكهربى / Power factor selectable |
| Overload class | Class 10eero |
| درجة الحرارة المحيطة | -25~+60 ℃; أقصى ارتفاع 4000 م (التخفيض مطلوب)eero |
- وظائف مدمجة
Soft start & توقف ناعم: منحدر الجهد, torque control ramp, بداية الحد الحالي, dual current limit mode
Pump cleaning & anti-surge functions (ideal for pump applications)
Jog / slow speed, pre-start, kick start
Dynamic braking & standstill braking
Limp mode: Two-phase reduced-capacity operation if one thyristor fails
Fire emergency mode: Bypass all protections to force run
الساعة في الوقت الحقيقي, event log, قياس الطاقة, thyristor running hour counter
Auto phase sequence detection & auto restart
الحماية الكاملة: Electronic overload, الدوار مقفل, خسارة المرحلة, عدم التوازن الحالي, التحميل الزائد, خطأ الأرض, over/under voltage, PTC/PT100 motor temperature monitoring, bypass fault, communication fault
واجهة المستخدم البشرية: Color graphical display, 17 اللغات, detachable with password lock
- التطبيقات النموذجية
مضخات المياه, المشجعين, الضواغط, الناقلات الحزامية, crushers and other heavy-duty equipment. The built-in bypass cuts off thyristor current after full speed, eliminating continuous heat loss and saving energy.
- Cross-Series & ملاحظات الاستبدال
- PSTX470-600-70 (رقم الطلب. 1SFA898116R7000): Max voltage 600V, cannot directly replace the 690V version
- PSTB470: Basic model without torque control, limp mode and pump cleaning; not an equivalent replacement
- البدائل المحلية: رينل, Xichi, Heping 470A/690V built-in bypass soft starters; communication and protection logic differ, PLC programs need modification
- تثبيت & نصائح الصيانة
- Two wiring options: In-line (الأكثر شيوعا) / Inside-delta (boost motor power rating; soft starter only carries branch winding current)
- Sufficient cabinet ventilation; derate power for +60℃ ambient or high altitude
- Regularly inspect built-in bypass contacts; thyristors and cooling fans are wearing parts
- Set Modbus RTU address and baud rate via the keypad; refer to PSTX official communication manual for register mapping
Working Principle of Thyristor Soft Starters (ABB PSTX Type)
A soft starter is essentially a thyristor (SCR) AC voltage regulator wired in series with the three-phase motor main circuit. It adjusts the thyristor firing angle to gradually raise motor terminal voltage for smooth ramp-up start, and gradually lower voltage for smooth ramp-down stop — no sudden full voltage jump as in direct-on-line or star-delta starting.
- المكون الأساسي: Anti-parallel Thyristors per Phase
Each phase has a pair of reverse-connected thyristors:
Small firing angle → short conduction time → low output voltage
Gradually increasing firing angle → voltage rises smoothly
Full firing angle → output voltage nearly equals grid rated voltage
Thyristors only trigger at voltage zero-crossing in each AC half-cycle, enabling precise voltage regulation.
- Start-Stop Sequence (Built-in Bypass Model like PSTX)
- تعليق: Bypass contactor open; all current flows through thyristor modules
- Soft Ramp-up: Controller increases thyristor conduction angle step by step; motor voltage climbs slowly, limiting inrush current (no 5~7× rated current surge of DOL start). Two main modes: voltage ramp or torque-controlled ramp (PSTX exclusive)
- Bypass Closure: When motor reaches full speed, the built-in bypass contactor closes. Current transfers to mechanical contacts; thyristors exit the main circuit with no continuous heat generation
- عملية عادية: Motor runs directly on mains; soft starter only monitors protection
- Soft Stop: Bypass opens again, switching back to thyristor voltage control; voltage ramps down slowly to stop the motor gently, eliminating water hammer in piping and mechanical shock on transmission parts
- Difference vs Star-Delta / Autotransformer Starters
Star-delta: Step voltage switching, still creates secondary current surges; only fixed voltage reduction ratio
Autotransformer: Step-down voltage only, bulky size, no continuous adjustable curve
Thyristor soft starter: stepless continuous voltage regulation, programmable start curves, plus braking, pump cleaning, full motor protection and fieldbus communication
- Two Common Starting Modes
بداية الحد الحالي: Lock maximum starting current first; voltage adjusts automatically to match load — preferred for heavy loads
Torque-controlled start (PSTX only): Regulates motor torque directly instead of pure voltage, delivering smoother acceleration with less mechanical impact
- Key Limitation
Thyristor voltage regulation only changes voltage amplitude, NOT frequency.
👉 Soft starter ≠ Variable Frequency Drive (VFD): Soft starters only control starting & stopping; they cannot run the motor continuously at variable speed. VFD adjusts both voltage and frequency for continuous speed regulation.
Common Faults for PSTX Built-in Bypass Soft Starters
- Heatsink / Thyristor Overheating (Fault F04xx)
أعراض: Trips after several starts; housing hot; cooling fan fails to run
الأسباب الجذرية:
Fan damaged or air duct blocked with dust
Cabinet sealed tightly; high ambient temperature or high altitude without derating
Bypass contactor fails to close; thyristors stay energized and overheat
Excessively long ramp time or frequent starts exceeding the 6 starts/hour limit
الحلول: الغبار النظيف, استبدل المروحة, verify start frequency, troubleshoot bypass circuit
- خسارة المرحلة / 3-Phase Current Imbalance (F03xx)
أعراض: Trips immediately on power-up; motor hums with heavy vibration
الأسباب الجذرية:
Blown fuses, open circuit breakers, loose terminal lugs or oxidized copper busbars
One-phase thyristor open-circuit or trigger failure
Broken motor winding or poor cable connection
امتياز: Input phase loss = supply side; Output phase loss = wiring between soft starter and motor or damaged SCR
- التيار الزائد / ماس كهربائى
أعراض: Instant trip on start; current far exceeds the set current limit
الأسباب الجذرية:
الدوار مغلق المحرك (blocked impeller, تحمل المضبوطة)
Cable or motor insulation breakdown (phase-phase or phase-earth short)
Starting voltage set too high or current limit value set too large
Thyristor short-circuited (do not retry starting repeatedly)
- Start Timeout (Failed to Reach Full Speed)
أعراض: Ramp finishes but motor never reaches rated speed; start timeout fault triggers
الأسباب الجذرية:
Current limit set too low or initial voltage too low (عزم الدوران غير كاف)
Excessive load inertia, closed valve or heavy mechanical resistance
Wrong motor rated current parameter or undersized motor
Severe grid voltage drop during start
- Bypass-Related Faults (Most Frequent on PSTX: F0613, bypass failure, اتصالات عالقة)
- Bypass fails to pull in: Thyristors remain energized and overheat rapidly
الأسباب: Damaged coil, insufficient control voltage, bypass function disabled in parameters, internal detection circuit failure
- Bypass contactor welded shut: Input and output permanently shorted; soft stop function fails completely; خطر السلامة
الأسباب: Frequent heavy-current cycling, arc erosion on contacts, repeated short-circuit surges
- Motor Overload Trip
أعراض: Trips after long running time, not during startup
الأسباب الجذرية:
Continuous overloaded operation, pump clogging, worn bearings
Incorrect motor rated current or Class 10 overload setting
Long low-speed operation leading to poor motor cooling; PTC/PT100 overtemperature alarm
- Underload Protection Trip
أعراض: Motor runs but current drops below threshold (dry-run protection for pumps/fans)
الأسباب الجذرية: Pump running dry, fully open valve with no load, broken belt or disconnected coupling
ملحوظة: Disable underload protection temporarily during no-load commissioning; re-enable after field commissioning.
- Thyristor SCR Damage (قصير / الدائرة المفتوحة)
أعراض: No clear fault code, but 3-phase current unbalanced, loss of voltage control, residual voltage on output after shutdown
الأسباب الجذرية: Grid surge / ضربات البرق, repeated heavy starts, poor cooling, output short-circuit impact
اختبار: Disconnect power and measure resistance across each thyristor; shorted SCR shows near-zero resistance between input and output. Damaged power modules cannot be repaired and must be replaced.
- التحكم في العرض & أخطاء الاتصال
No power on HMI: شاشة سوداء, random faults → low 100–250V control supply or blown internal fuse
Modbus RTU communication loss: PLC cannot read data → mismatched address/baud rate, poor shielding or ground interference
- Phase Sequence Fault
أعراض: Phase reversal alarm on power-up; start inhibited
السبب الجذري: Incoming three-phase wiring reversed. You can disable phase sequence check temporarily (not recommended for permanent operation).
- Failed Soft Stop (Water Hammer)
أعراض: Motor stops abruptly, causing severe pipeline water hammer
الأسباب الجذرية: Soft stop ramp time set too short; welded bypass contactor prevents switching back to thyristor control, resulting in direct hard stop.
Fast On-Site Troubleshooting Sequence (PSTX Recommended)
- Check fault code and event log on the graphical display (PSTX stores full historical records)
- Cut off power and inspect all main terminals & busbars for overheating and loose connections
- Disconnect the motor and run no-load test to isolate faults: soft starter failure vs motor/mechanical load failure
- Verify bypass contactor operation and cooling fan rotation
- Double-check that all motor nameplate parameters match the soft starter settings
Full PSTX Series Model List (تجاوز مدمج)
PSTX xxx-600-70 (208~600V AC)
| نموذج | رقم الطلب. | التصنيف الحالي | 400قوة الخامس |
| PSTX30-600-70 | 1SFA898103R7000 | 30 أ | 15 كيلوواط |
| PSTX37-600-70 | 1SFA898104R7000 | 37 أ | 18.5 كيلوواط |
| PSTX45-600-70 | 1SFA898105R7000 | 45 أ | 22 كيلوواط |
| PSTX60-600-70 | 1SFA898106R7000 | 60 أ | 30 كيلوواط |
| PSTX72-600-70 | 1SFA898107R7000 | 72 أ | 37 كيلوواط |
| PSTX85-600-70 | 1SFA898108R7000 | 85 أ | 45 كيلوواط |
| PSTX105-600-70 | 1SFA898109R7000 | 105 أ | 55 كيلوواط |
| PSTX142-600-70 | 1SFA898110R7000 | 142 أ | 75 كيلوواط |
| PSTX170-600-70 | 1SFA898111R7000 | 170 أ | 90 كيلوواط |
| PSTX210-600-70 | 1SFA898112R7000 | 210 أ | 110 كيلوواط |
| PSTX250-600-70 | 1SFA898113R7000 | 250 أ | 132 كيلوواط |
| PSTX300-600-70 | 1SFA898114R7000 | 300 أ | 160 كيلوواط |
| PSTX370-600-70 | 1SFA898115R7000 | 370 أ | 200 كيلوواط |
| PSTX470-600-70 | 1SFA898116R7000 | 470 أ | 250 كيلوواط |
| PSTX570-600-70 | 1SFA898117R7000 | 570 أ | 315 كيلوواط |
| PSTX720-600-70 | 1SFA898118R7000 | 720 أ | 400 كيلوواط |
| PSTX840-600-70 | 1SFA898119R7000 | 840 أ | 450 كيلوواط |
| PSTX1050-600-70 | 1SFA898120R7000 | 1050 أ | 560 كيلوواط |
| PSTX1250-600-70 | 1SFA898121R7000 | 1250 أ | 710 كيلوواط |
PSTX xxx-690-70 (208~690V AC, including PSTX470-690-70)
| نموذج | رقم الطلب. | حاضِر | 400V kW | 690V kW |
| PSTX30-690-70 | 1SFA898203R7000 | 30 أ | 15 | 25 |
| PSTX37-690-70 | 1SFA898204R7000 | 37 أ | 18.5 | 30 |
| PSTX45-690-70 | 1SFA898205R7000 | 45 أ | 22 | 37 |
| PSTX60-690-70 | 1SFA898206R7000 | 60 أ | 30 | 45 |
| PSTX72-690-70 | 1SFA898207R7000 | 72 أ | 37 | 55 |
| PSTX85-690-70 | 1SFA898208R7000 | 85 أ | 45 | 59 |
| PSTX105-690-70 | 1SFA898209R7000 | 105 أ | 55 | 75 |
| PSTX142-690-70 | 1SFA898210R7000 | 142 أ | 75 | 90 |
| PSTX170-690-70 | 1SFA898211R7000 | 170 أ | 90 | 132 |
| PSTX210-690-70 | 1SFA898212R7000 | 210 أ | 110 | 160 |
| PSTX250-690-70 | 1SFA898213R7000 | 250 أ | 132 | 184 |
| PSTX300-690-70 | 1SFA898214R7000 | 300 أ | 160 | 220 |
| PSTX370-690-70 | 1SFA898215R7000 | 370 أ | 200 | 257 |
| PSTX470-690-70 | 1SFA898216R7000 | 470 أ | 250 | 355 |
| PSTX570-690-70 | 1SFA898217R7000 | 570 أ | 315 | 450 |
| PSTX720-690-70 | 1SFA898218R7000 | 720 أ | 400 | 560 |
| PSTX840-690-70 | 1SFA898219R7000 | 840 أ | 450 | 710 |
| PSTX1050-690-70 | 1SFA898220R7000 | 1050 أ | 560 | 800 |
| PSTX1250-690-70 | 1SFA898221R7000 | 1250 أ | 710 | 1000 |
PSTB Basic Series (Reduced Functions, تجاوز مدمج)
| نموذج | رقم الطلب. | حاضِر | 400قوة الخامس |
| PSTB370-600-70 | 1SFA894015R7000 | 370 أ | 200 كيلوواط |
| PSTB470-600-70 | 1SFA894016R7000 | 470 أ | 250 كيلوواط |
| PSTB570-600-70 | 1SFA894017R7000 | 570 أ | 315 كيلوواط |
| PSTB720-600-70 | 1SFA894018R7000 | 720 أ | 400 كيلوواط |
| PSTB840-600-70 | 1SFA894019R7000 | 840 أ | 450 كيلوواط |
| PSTB1050-600-70 | 1SFA894020R7000 | 1050 أ | 560 كيلوواط |
PSTB does not support torque control, limp mode or pump cleaning. Only for simple fan & pump start-stop; not a direct replacement for PSTX.
PSR Compact Soft Starters (اقتصادية, NO Built-in Bypass)
| نموذج | رقم الطلب. | حاضِر | 400قوة الخامس |
| PSR3-600-70 | 1SFA896103R7000 | 3 أ | 0.75 كيلوواط |
| PSR6-600-70 | 1SFA896104R7000 | 6 أ | 1.5 كيلوواط |
| PSR9-600-70 | 1SFA896105R7000 | 9 أ | 2.2 كيلوواط |
| PSR12-600-70 | 1SFA896106R7000 | 12 أ | 3 كيلوواط |
| PSR16-600-70 | 1SFA896107R7000 | 16 أ | 4 كيلوواط |
| PSR25-600-70 | 1SFA896108R7000 | 25 أ | 5.5 كيلوواط |
| PSR30-600-70 | 1SFA896109R7000 | 30 أ | 7.5 كيلوواط |
| PSR37-600-70 | 1SFA896110R7000 | 37 أ | 11 كيلوواط |
| PSR45-600-70 | 1SFA896111R7000 | 45 أ | 15 كيلوواط |
| PSR60-600-70 | 1SFA896112R7000 | 60 أ | 18.5 كيلوواط |
| PSR72-600-70 | 1SFA896113R7000 | 72 أ | 22 كيلوواط |
| PSR85-600-70 | 1SFA896114R7000 | 85 أ | 30 كيلوواط |
| PSR105-600-70 | 1SFA896115R7000 | 105 أ | 37 كيلوواط |
Series Quick Comparison
- بي اس تي اكس: High-end flagship, color HMI, التحكم في عزم الدوران, braking, pump cleaning, مودبوس, الحماية الكاملة, تجاوز مدمج; preferred for export industrial projects
- PSTB: Mid-range basic model, monochrome screen, limited functions, تجاوز مدمج
- بي إس آر: Compact low-cost version, لا يوجد تجاوز مدمج, requires external bypass contactor; only for small-power motors
- بي.اس.اس / توقيت المحيط الهادئ: Older legacy models, التخلص التدريجي; only available as spare parts for existing installations, لا ينصح به للمشاريع الجديدة
Optional Communication Accessories (بي اس تي اكس)
PS-FBPA: 1SFA896312R1002, basic fieldbus adapter
PSTX ANYBUS Modbus RTU: 1SFA899300R1003
المقاولين,قاطع الدائرة,الاستشعار,التشفير,بلك,محول



















NH42-63-318x560.png)



