OMRON CP1W-8ER Pure Output Expansion Module - Schütz,Leistungsschalter,Sensor,Encoder,SPS,Konverter

Wechat: +86-13184948252 WhatsApp: 0086-13811255435 E-Mail: kent@bestcontactor.com

Um Kontakt |

OMRON CP1W-8ER Pure Output Expansion Module - Schütz,Leistungsschalter,Sensor,Encoder,SPS,Konverter

SPS/

OMRON CP1W-8ER Pure Output Expansion Module

CP1W: Expansion unit for CP1 series 8: 8 points E: Expansion R: Relay normally open (NEIN) output Type: Pure output expansion module, no input points Core Specifications Number of output points: 8-point relay NO output Rated current per channel: 2 A (ohmsche Last) Output voltage range: AC/DC 4.5~30 V (passive relay contact) On/off delay: ca. ...

  • Produktdetails

CP1W: Expansion unit for CP1 series

8: 8 Punkte

E: Erweiterung

R: Relay normally open (NEIN) Ausgabe

Typ: Pure output expansion module, no input points

Kernspezifikationen

Number of output points: 8-point relay NO output

Nennstrom pro Kanal: 2 A (ohmsche Last)

Output voltage range: AC/DC 4.5~30 V (passive relay contact)

On/off delay: ca. 15 MS

Stromverbrauch: 5 In DC 0.21 A; 24 In DC 0.13 A

Abmessungen: W66 × H90 × D50 mm

Gewicht: ca. 250 G

Zertifizierungen: CE, UL, CSA

Lebenszyklusstatus: Aktiv, not discontinued

Kompatibel CPU Einheiten

CP1E / CP1H / CP1L (CP1 series PLC); also compatible with legacy CPM1A/CPM2A

Notiz: 20-point CP1E CPU does not support expansion. Only 30/40/60-point CPUs can connect CP1W expansion units.

Cross-model Comparison (zur Auswahl)

CP1W-8ER: 8-Punktrelaisausgang (passiv, AC/DC universal)

CP1W-8ET: 8-Punkt NPN-Transistorausgang (Nur DC24V)

CP1W-8ED: 8-Punkt DC24V Eingabemodul

CP1W-16ER: 16-Punktrelaisausgang

Verkabelungsrichtlinien

  1. Two independent common terminals: COM0 (00~03), COM1 (04~07)
  2. Relay is dry contact: connect AC L / DC+ to COM as required, then wire the load to the contact terminal
  3. Do not drive high-power motors directly; add intermediate contactors
  4. Für induktive Lasten (Magnetventile, Spulen), install freewheeling diodes (Gleichstrom) oder RC-Snubber (Wechselstrom) to extend relay life.

Fehlerbehebung

Keine Ausgabeaktion:

1) Check if the expansion cable is firmly plugged in and the CPU recognizes the expansion unit

2) Verify the I/O address assignment (expansion I/O follows the previous unit’s address sequentially)

3) Measure COM power supply and check for open circuits in the load loop

Permanent ON for one channel: relay contact welding; replace the point or the whole module

No output on all channels: expansion function disabled, too many expansion units, or damaged cable.

Ersatzoptionen

  1. Direkter Ersatz: CP1W-8ER (bevorzugt, no program modification needed)
  2. Transistor alternative: CP1W-8ET (for high-frequency switching and DC loads; cannot handle AC)
  3. Inländische Alternative: CP1-bus compatible 8-point relay expansion module (verify bus protocol and address mapping)

Service Life of CP1W-8ER (Limited by relay contacts)

Official rated life per relay channel

  1. Mechanisches Leben (no-load operation): ≥20 million operations
  2. Elektrisches Leben (2 Eine ohmsche Last): ≥100.000 Betätigungen

Kernpunkt: Electrical life is the bottleneck, not the PCB. Induktive Lasten (Magnetventile, Schützspulen) drastically shorten service life down to 20,000~50,000 cycles. Snubber circuits will improve this.

Time Estimation (for project evaluation)

1 operation per minute: 100,000 cycles ≈ 19 Jahre

1 operation per 10 Sekunden: 100,000 cycles ≈ 2.8 Jahre

1 operation per second: 100,000 cycles ≈ 27 Std.

For equipment with continuous ON state and rare switching: contact wear is minimal. In clean, temperature-controlled cabinets, the PCB, cable and terminals can run stably for 8~15 years. Service life is halved in high-temperature, feuchte und staubige Umgebungen.

Two Types of Service Life

Kontakt zum Leben: limited by switching cycles; failure symptoms: contact welding or poor contact

Module body life: Leiterplatte, cable and drive circuit; aging depends on environmental conditions, no fixed cycle rating.

Life Extension Tips

  1. Add freewheeling diodes (Gleichstrom) oder RC-Snubber (Wechselstrom) for inductive loads such as solenoid valves and contactors.
  2. Keep load current below 1 A; avoid continuous full-load (2 A) Betrieb.
  3. For high-frequency switching (cycles within seconds), use CP1W-8ET transistor output instead of ER relay modules.
  4. Regularly inspect expansion cables and terminals for oxidation and loose connections.

Full List of OMRON CP1W Expansion Units (CP1E / CP1H / CP1L Compatible)

Notiz: CP1W units are bus-connected expansion modules (daisy-chained with flat cable). CIF, ADB and DAB boards are CPU side option boards (not bus expansion units). 20-point CP1E cannot use expansion units; only 30/40/60-point CP1E, CP1H and CP1L-M support CP1W expansion.

  1. Digital Input Only Units
ModellBeschreibung
CP1W-8ED8-Punkt DC24V-Eingang (NPN/PNP universell)
  1. Digital Output Only Units (CP1W-8ER listed here)
ModellBeschreibung
CP1W-8ER8-point relay NO output, 2 A
CP1W-8ET8-point NPN (sinken) Transistorausgang, 0.3 A
CP1W-8ET18-point PNP (Beschaffung) Transistorausgang, 0.3 A
CP1W-16ER16-point relay NO output, 2 A
CP1W-16ET16-Punkt NPN-Transistorausgang, 0.3 A
CP1W-16ET116-point PNP transistor output, 0.3 A
CP1W-32ER32-point relay NO output, 2 A
CP1W-32ET32-Punkt NPN-Transistorausgang, 0.3 A
CP1W-32ET132-point PNP transistor output, 0.3 A
  1. Gemischte E/A-Einheiten (Eingang + Output integrated)
ModellBeschreibung
CP1W-20EDR112 DC inputs + 8 Relaisausgänge
CP1W-20EDT12 DC inputs + 8 NPN transistor outputs
CP1W-20EDT112 DC inputs + 8 PNP transistor outputs
CP1W-40EDR24 DC inputs + 16 Relaisausgänge
CP1W-40EDT24 DC inputs + 16 NPN transistor outputs
CP1W-40EDT124 DC inputs + 16 PNP transistor outputs
  1. Analog I/O Units (Stromspannung / Aktuelles Signal)
ModellBeschreibung
CP1W-AD0414 KI, Auflösung 1/6000; voltage/current selectable
CP1W-AD0424 KI, hohe Auflösung 1/12000
CP1W-DA0212 ZUM, Auflösung 1/6000
CP1W-DA0414 ZUM, Auflösung 1/6000
CP1W-DA0424 ZUM, hohe Auflösung 1/12000
CP1W-MAD112 KI + 1 ZUM, Auflösung 1/6000
CP1W-MAD424 KI + 2 ZUM, hohe Auflösung 1/12000 (am beliebtesten)
  1. Temperature Input Units (Thermoelement / Pt RTD)
ModellBeschreibung
CP1W-TS0012-Kanal-Thermoelement (K/J type)
CP1W-TS0022-channel Pt100/Pt1000 RTD
CP1W-TS0032-channel multi-function: Thermoelement / FTE / analoger Eingang
CP1W-TS00412-Kanal-Thermoelement (for oven & injection molding multi-point temperature monitoring)
  1. Zubehör (Erweiterungskabel)
ModellBeschreibung
CP1W-CN81180 cm extension cable; short cable (6 cm) included with each module

Ergänzend: CPU Side Option Boards (NOT Bus Expansion Units)

These plug directly into the CPU side slot and cannot be daisy-chained on the I/O bus:

CP1W-CIF01: RS232C

CP1W-CIF11: Non-isolated RS422/485

CP1W-CIF12 / CIF12-V1: Opto-isolated RS422/485

CP1W-CIF41: Ethernet-Optionsplatine

CP1W-DAM01: LCD display panel

CP1W-ADB21 / DAB21V / MAB221: Small analog option boards

Kurzanleitung zur Auswahl

  1. Hochfrequenzschaltung, Magnetventile, servo pulse output → Choose ET / ET1 transistor models, do not use ER relay modules
  2. AC220V loads with infrequent switching → Select ER relay models
  3. Thermocouple temperature measurement: TS001; Pt RTD: TS002; multi-point temperature monitoring: TS004
  4. Analoge E/A: MAD42 (4-rein 2 raus) wird bevorzugt; new projects select high-resolution AD042 / DA042

 

Vorher:

Nächste:

Hinterlassen Sie eine Antwort

Eine Nachricht hinterlassen