contactor,cortacircuitos,inversor solar,medidor electrico,sensor,Codificador,SOCIEDAD ANÓNIMA
Bulletin 284D ArmorStart Distributed Motor Controller (Integrated VFD, DeviceNet Communication, Safetyrated)
⚠️Lifecycle: Officially discontinued on Oct082024. No direct dropin OEM replacement. Engineeringlevel replacement only; available via used/sparepart channels only.
Desglose del código del modelo
284DFVD2P3Z10CR3
| Segmento | Descripción |
| 284D | ArmorStart distributed variable‑frequency drive base unit with safety functions |
| FVD | Variable‑Frequency Drive, sensorless vector control |
| 2P3 | 2.3 A output current; 0.75 kilovatios (1 HP) @ 480 V |
| z | Control module option: No HOA hand‑off‑auto keypad |
| 10 | 10 A short‑circuit protective rating for the device |
| CR | Conduit entrance (threaded conduit port, non‑ArmorConnect quick‑connect connector), supplied with pre‑fabricated motor cable |
| 3 | Safety variant: Safe‑Torque‑Off (STO) |
NoEMI suffix: This unit does NOT include builtin EMI filter. Full partnumber with EMI filter: 284DFVD2P3Z10CREMI3
Especificaciones eléctricas básicas
Voltaje de entrada: 3phase 380480 V AC, 50/60 Hz
Nominal Power: 0.75 kilovatios / 1 HP
VFD Output Current: 2.3 A
Comunicación: DispositivoNet (125/250/500 kbps)
E/S integradas: 4 Entradas digitales / 2 Salidas digitales de relé
Frecuencia de salida: 0400 Hz; Vector sin sensores / VHz control
Protecciones: Class 10 electronic overload, Yo²t, sobrecorriente, sobretensión, subtensión
Clasificación del gabinete: IP67 / NEMA 4, machinemount distributed drive
Stop Modes: Ramptostop, coasttostop, DCbraking, Scurve
Seguridad: SafeTorqueOff (STO), suffix3 safety variant
Interfaces & Mechanical Details
- CR = Threaded conduit entry for power wiring; differs from RR = ArmorConnect quickdisconnect circular connector
- Internal cooling fan; intended for machineside mounting, reduces cabinetinternal cabling work
- Configuration software: RSNetWorx for DeviceNet
SparePart Breakdown for Repairinplace
Drivecontrol module only: 284DFVD2P3ZNR
Base housing only: 280DFN10C
Motorcable spare: 280MTR22M3 (3meter length)
Engineering Replacement Options
DeviceNetbased 284D series is discontinued. Two primary migration paths:
- Retain DeviceNet network: Fuente utilizada / refurbished spare units. STO safetyfunction validation is mandatory after replacement.
- Upgrade to EtherNet/IP: Adopt 284E ArmorStart ST (Ethernetbased variant). Requires network reengineering, I/O remapping and mountinghole dimensional verification.
Nota: 284D and 284E are not pintopin direct swaps despite similar mechanical outline.
Fault Codes for 284DFVD2P3Z10CR3 + 284E Migration Reference Table
This drive uses a PowerFlexderived core. Faults fall into MCB maincontrolboard faults and VFD powerstage faults. Read the last 3 fault records via parameter 107109; read full fault description via parameter 61.
Common Field Fault Codes
| Código de falla | Nombre de falla | Fenómeno & Solución de problemas |
| F001 | sobrecorriente | Output short‑circuit, motor ground‑fault, damaged motor cable. Inspect wiring inside CR conduit, check motor insulation; reduce carrier frequency if needed. |
| F002 | Auxiliary Input Fault | External safety interlock / STO channel open. Unit is suffix‑3 STO‑equipped; verify both STO wiring loops are properly jumpered. |
| F003 | Sobretensión | Deceleration time too short, regenerative energy. Extend deceleration ramp time; add braking resistor if required. |
| F004 | Subtensión | 3-pérdida de fase de entrada de fase, large voltage drop at supply. Measure L1/L2/L3 line‑to‑line voltages. Low 24 V DeviceNet bus supply can trigger similar symptoms. |
| F008 | Heatsink Overtemp | Machine‑mount IP67 installation; high ambient temperature or blocked / seized internal cooling fan. Inspect fan rotation and heat‑dissipation paths. |
| F011 | Internal Communication Fault | Communication loss between MCB main‑board and VFD power‑stage. Power‑cycle first; frequent recurrence indicates hardware failure, replace 284D‑FVD2P3Z‑N‑R drive module. |
| F012 | Falla a tierra | Motor‑side earth leakage. Test motor‑to‑ground insulation; inspect for damaged cabling. |
| F033 | Auto‑Restart Retries Exhausted | Maximum auto‑reset attempts reached. Resolve root‑cause of tripping instead of only clearing fault buffer. |
| F048 | Parameters Reset to Factory Default | Abnormal power‑loss or firmware anomaly. All user parameters lost; full parameter download required. |
| F080 | Motor Autotune Failure | Incorrect motor‑nameplate data entered; autotune executed with load coupled to motor shaft. |
| F16 | Miscellaneous Fault | Aggregates overheat, falla del ventilador, corrupción de parámetros, braking‑circuit errors. Read parameter 61 for underlying sub‑fault details. |
LEDbased troubleshooting:
- Fast red blink: VFD powerstage fault
- Slow red blink: DeviceNet communication fault. Check bus termination resistors, node address, 24 V bus power supply.
- Suffix3 STO variant: STOloop open triggers red safetyLED; inverter output is hardblocked. Fault must be acknowledged before operation is restored.
Configuration tool: RSNetWorx for DeviceNet retrieves fault history; no local HIM keypad, parameters accessible only over fieldbus.
Migration Reference: 284D (DispositivoNet) → 284E (Ethernet/IP)
Original partnumber: 284DFVD2P3Z10CR3
Spec: 0.75 kilovatios / 1 HP, 2.3 A, No HOA keypad (z), 10 A SCCR rating, CR threadedconduit port, STO safety (3), no builtin EMI filter.
✅ Recommended 284E replacement partnumber: 284EFVD2P3Z10CR3
| Artículo | Original 284D‑FVD2P3Z‑10‑CR‑3 | Replacement 284E‑FVD2P3Z‑10‑CR‑3 | Diferencias clave |
| Comunicación | DispositivoNet | Ethernet/IP (DLR ring‑topology support) | Protocol‑incompatible; no intercambio directo. PLC project modification mandatory. |
| Fuerza / Actual | 0.75 kilovatios, 2.3 A | 0.75 kilovatios, 2.3 A | Identical power rating |
| Local Keypad | Z = No HOA keypad | Z = No HOA keypad | Idéntico |
| Short‑circuit rating | 10 A | 10 A | Idéntico |
| Interfaz de cableado | CR threaded conduit + pre‑made motor cable | CR threaded conduit + pre‑made motor cable | Identical mechanical interface |
| Funciones de seguridad | ‑3 Safe‑Torque‑Off | ‑3 Safe‑Torque‑Off | Identical safety functions; safety‑validation test still required post‑replacement. |
| EMI Filter | No internal EMI filter | No internal EMI filter | For EMI‑compliant version add suffix‑EMI: 284E‑FVD2P3Z‑10‑CR‑EMI‑3 |
| Recinto | IP67 / NEMA 4 | IP67 / NEMA 4 | Identical environmental rating |
| On‑board I/O | 4DE / 2 Relay DO | 4DE / 2 Relay DO | Same I/O count, but I/O mapping tables completely different. |
| Mounting Footprint | 284D base housing | 284E base housing | Mounting hole pattern compatible, but modules cannot be hot‑swapped; base‑part numbers differ. |
SparePart Breakdown for 284E
Drivecontrol module only: 284EFVD2P3ZNR
Base housing only: 280EFN10C
Motorcable spare: 280MTR22M3 (cable crosscompatible with 284D)
Two Replacement Strategies
Option A: Preserve existing DeviceNet network (no PLC reprogramming)
- Fuente utilizada / refurbished 284DFVD2P3Z10CR3. OEM endoflife, no new stock.
- Swap only drivemodule 284DFVD2P3ZNR while reusing existing base 280DFN10C. No changes to external power wiring or conduit connections.
- Riesgos: Unknown residual servicelife of preowned hardware. Mandatory STO safetyvalidation after module replacement.
Option B: Upgrade to 284E with EtherNet/IP (preferred for longterm support)
- Target partnumber: 284EFVD2P3Z10CR3
- Required modifications:
Remove DeviceNet cabling; install EtherNet/IP copper cabling; DLR ring topology supported.
PLC programming: Delete DeviceNet I/O mappings, reconfigure EtherNet/IP tagbased I/O.
Parámetros: Parameter files cannot be imported from 284D to 284E. Manually reenter motornameplate data, ramptimes, faulthandling settings.
- Mecánico: Directfit mounting on original installation location; CR conduit ports and powermotor cables can be reused.
⚠️Important: 284D and 284E firmwareparameter files are incompatible. Parameter uploaddownload copypaste is not supported; manual recommissioning is required.
Alternative Hybrid Migration (Avoid PLC rewrite, reject used hardware)
Deploy DeviceNettoEtherNet/IP gateway. Retain original DeviceNetside logic and program structure; upperlevel PLC runs EtherNet/IP. Wellsuited for fleetsize multiunit retrofits.
Acceptancetest Checklist for Used / Refurbished Units
- Poweron STOloop functional test: Confirm STOopen triggers safetyfault; jumpered STO enables drive readiness.
- Noload motor runtest: Ramp frequency 050 Hz, verify no recurring F001 overcurrent or F008 overtemperature faults.
- Read faulthistory parameters 107109; confirm no persistent historical faults.
- DeviceNet communication test: Modify node address, verify cyclic I/O readwrite over bus.
- Inspect coolingfan operation; inspect IP67 housing seals for aging and cracking.
