OMRON CP1W-8ER Pure Output Expansion Module - Contacteur,disjoncteur,capteur,Encodeur,API,Convertisseur

Wechat: +86-13184948252 WhatsApp: 0086-13811255435 E-mail: kent@bestcontactor.com

À propos Contact |

OMRON CP1W-8ER Pure Output Expansion Module - Contacteur,disjoncteur,capteur,Encodeur,API,Convertisseur

API/

OMRON CP1W-8ER Pure Output Expansion Module

CP1W: Expansion unit for CP1 series 8: 8 points E: Expansion R: Relay normally open (NON) output Type: Pure output expansion module, no input points Core Specifications Number of output points: 8-point relay NO output Rated current per channel: 2 UN (charge résistive) Output voltage range: AC/DC 4.5~30 V (passive relay contact) On/off delay: environ. ...

  • Détails du produit

CP1W: Expansion unit for CP1 series

8: 8 points

E: Expansion

R.: Relay normally open (NON) sortir

Taper: Pure output expansion module, no input points

Spécifications de base

Number of output points: 8-point relay NO output

Rated current per channel: 2 UN (charge résistive)

Output voltage range: AC/DC 4.5~30 V (passive relay contact)

On/off delay: environ. 15 MS

Consommation d'énergie: 5 À DC 0.21 UN; 24 À DC 0.13 UN

Dimensions: W66 × H90 × D50 mm

Poids: environ. 250 g

Certifications: CE, UL, ASC

Lifecycle status: Actif, non discontinué

Compatible Processeur Unités

CP1E / CP1H / CP1L (CP1 series PLC); also compatible with legacy CPM1A/CPM2A

Note: 20-point CP1E CPU does not support expansion. Only 30/40/60-point CPUs can connect CP1W expansion units.

Cross-model Comparison (for selection)

CP1W-8ER: 8-sortie relais ponctuelle (passive, AC/DC universel)

CP1W-8ET: 8-sortie transistor NPN (DC24V seulement)

CP1W-8ED: 8-point DC24V module d'entrée

CP1W-16ER: 16-sortie relais ponctuelle

Directives de câblage

  1. Two independent common terminals: COM0 (00~03), COM1 (04~07)
  2. Relay is dry contact: connect AC L / DC+ to COM as required, then wire the load to the contact terminal
  3. Ne conduisez pas directement des moteurs de grande puissance; add intermediate contactors
  4. Pour charges inductives (électrovannes, bobines), install freewheeling diodes (CC) or RC snubbers (CA) to extend relay life.

Dépannage

Aucune action de sortie:

1) Check if the expansion cable is firmly plugged in and the CPU recognizes the expansion unit

2) Verify the I/O address assignment (expansion I/O follows the previous unit’s address sequentially)

3) Measure COM power supply and check for open circuits in the load loop

Permanent ON for one channel: relay contact welding; replace the point or the whole module

No output on all channels: expansion function disabled, too many expansion units, or damaged cable.

Options de remplacement

  1. Remplacement direct: CP1W-8ER (préféré, no program modification needed)
  2. Transistor alternative: CP1W-8ET (for high-frequency switching and DC loads; cannot handle AC)
  3. Alternative nationale: CP1-bus compatible 8-point relay expansion module (verify bus protocol and address mapping)

Service Life of CP1W-8ER (Limited by relay contacts)

Official rated life per relay channel

  1. Durée de vie mécanique (fonctionnement à vide): ≥20 million operations
  2. Durée de vie électrique (2 Une charge résistive): ≥100 000 opérations

Point clé: Electrical life is the bottleneck, not the PCB. Charges inductives (électrovannes, bobines de contacteur) drastically shorten service life down to 20,000~50,000 cycles. Snubber circuits will improve this.

Time Estimation (for project evaluation)

1 operation per minute: 100,000 cycles ≈ 19 années

1 operation per 10 secondes: 100,000 cycles ≈ 2.8 années

1 operation per second: 100,000 cycles ≈ 27 heures

For equipment with continuous ON state and rare switching: contact wear is minimal. In clean, temperature-controlled cabinets, the PCB, cable and terminals can run stably for 8~15 years. Service life is halved in high-temperature, humid and dusty environments.

Two Types of Service Life

Contact life: limited by switching cycles; failure symptoms: contact welding or poor contact

Module body life: PCB, cable and drive circuit; aging depends on environmental conditions, no fixed cycle rating.

Life Extension Tips

  1. Add freewheeling diodes (CC) or RC snubbers (CA) for inductive loads such as solenoid valves and contactors.
  2. Keep load current below 1 UN; avoid continuous full-load (2 UN) opération.
  3. For high-frequency switching (cycles within seconds), use CP1W-8ET transistor output instead of ER relay modules.
  4. Regularly inspect expansion cables and terminals for oxidation and loose connections.

Full List of OMRON CP1W Expansion Units (CP1E / CP1H / CP1L Compatible)

Note: CP1W units are bus-connected expansion modules (daisy-chained with flat cable). CIF, ADB and DAB boards are CPU side option boards (not bus expansion units). 20-point CP1E cannot use expansion units; only 30/40/60-point CP1E, CP1H and CP1L-M support CP1W expansion.

  1. Digital Input Only Units
ModèleDescription
CP1W-8ED8-point d'entrée DC24V (NPN/PNP universel)
  1. Digital Output Only Units (CP1W-8ER listed here)
ModèleDescription
CP1W-8ER8-point relay NO output, 2 UN
CP1W-8ET8-point NPN (sinking) sortie transistorisée, 0.3 UN
CP1W-8ET18-point PNP (sourcing) sortie transistorisée, 0.3 UN
CP1W-16ER16-point relay NO output, 2 UN
CP1W-16ET16-sortie transistor NPN, 0.3 UN
CP1W-16ET116-point PNP transistor output, 0.3 UN
CP1W-32ER32-point relay NO output, 2 UN
CP1W-32ET32-sortie transistor NPN, 0.3 UN
CP1W-32ET132-point PNP transistor output, 0.3 UN
  1. Mixed I/O Units (Saisir + Output integrated)
ModèleDescription
CP1W-20EDR112 DC inputs + 8 sorties relais
CP1W-20EDT12 DC inputs + 8 NPN transistor outputs
CP1W-20EDT112 DC inputs + 8 PNP transistor outputs
CP1W-40EDR24 DC inputs + 16 sorties relais
CP1W-40EDT24 DC inputs + 16 NPN transistor outputs
CP1W-40EDT124 DC inputs + 16 PNP transistor outputs
  1. Analog I/O Units (Tension / Signal actuel)
ModèleDescription
CP1W-AD0414 IA, résolution 1/6000; tension/courant sélectionnable
CP1W-AD0424 IA, haute résolution 1/12000
CP1W-DA0212 AU, résolution 1/6000
CP1W-DA0414 AU, résolution 1/6000
CP1W-DA0424 AU, haute résolution 1/12000
CP1W-MAD112 IA + 1 AU, résolution 1/6000
CP1W-MAD424 IA + 2 AU, haute résolution 1/12000 (le plus populaire)
  1. Temperature Input Units (Thermocouple / Pt RTD)
ModèleDescription
CP1W-TS0012-channel thermocouple (K/J type)
CP1W-TS0022-channel Pt100/Pt1000 RTD
CP1W-TS0032-channel multi-function: thermocouple / RDT / entrée analogique
CP1W-TS00412-channel thermocouple (for oven & injection molding multi-point temperature monitoring)
  1. Accessoires (Expansion Cable)
ModèleDescription
CP1W-CN81180 cm extension cable; short cable (6 cm) included with each module

Supplémentaire: CPU Side Option Boards (NOT Bus Expansion Units)

These plug directly into the CPU side slot and cannot be daisy-chained on the I/O bus:

CP1W-CIF01: RS232C

CP1W-CIF11: Non-isolated RS422/485

CP1W-CIF12 / CIF12-V1: Opto-isolated RS422/485

CP1W-CIF41: Ethernet option board

CP1W-DAM01: LCD display panel

CP1W-ADB21 / DAB21V / MAB221: Small analog option boards

Guide de sélection rapide

  1. High-frequency switching, électrovannes, servo pulse output → Choose ET / ET1 transistor models, do not use ER relay modules
  2. AC220V loads with infrequent switching → Select ER relay models
  3. Thermocouple temperature measurement: TS001; Pt RTD: TS002; multi-point temperature monitoring: TS004
  4. E/S analogiques: MAD42 (4-in 2-out) est préféré; new projects select high-resolution AD042 / DA042

 

Précédent:

Suivant:

Laisser une réponse

Laisser un message