Sensore di livello conduttivo Carlo Gavazzi 481046

Carlo Gavazzi VNY 4 NS/NT Sensore di livello conduttivo (Articolo n.: 481046)

2. Full Core Technical Specifications

3. VNY Series Full Model List

4. Sostituzione & Riferimento incrociato

4.1 Same Brand Direct Replacement

4.2 Modelli equivalenti multimarca

5. Application Industries & Casi tipici

Applicazioni consigliate

1. Industria di processo: Tank level monitoring in chemical, petrochemical and pharmaceutical industries to prevent overflow and dry running
2. Cibo & Bevanda: Raw material and finished tank level control for beer, beverage and dairy production lines
3. Trattamento delle acque: Level monitoring for sedimentation tanks and reaction tanks in waterworks and wastewater plants
4. Settore energetico: Level protection for cooling and lubrication systems in power plants and substations
5. Mechanical Manufacturing: Oil level monitoring for hydraulic and lubrication systems to avoid equipment damage
6. Industria marina: Level measurement for ship ballast tanks, fuel tanks and fresh water tanks

Casi applicativi tipici

1. Chemical Plant Acid & Alkali Tank Level Control System

Application Goal: Monitor high/low levels of three 100m³ acid and alkali tanks to prevent overflow and pump dry running

Vantaggi fondamentali: AISI316 corrosion-resistant electrodes; IP67 suitable for outdoor installation; 4-electrode enables multi-point level monitoring

Configurazione del sistema: VNY 4 NS/NT (481046) × 3 + ELA amplifier relay + PLC control system + Touchscreen dell'interfaccia utente

Operation Effect: Level control accuracy ±1cm, false alarm rate reduced by 95%, costi di manutenzione ridotti 60%

2. Automobile Factory Hydraulic Station Oil Level Monitoring System

Application Goal: Monitor oil levels of 5 hydraulic stations to ensure stable operation and prevent oil shortage failure

Vantaggi fondamentali: Vibration-resistant screw terminal design; oil-resistant PBTP housing; field-cuttable electrodes adaptable to various tank heights

Configurazione del sistema: VNY 4 NS/NT (481046) × 5 + S196 amplifier + indicatore luminoso + cicalino

Operation Effect: Equipment failure rate reduced by 40%, maintenance cycle doubled

Applicazioni non consigliate

Non-conductive liquids: Such as pure oil, alcohol, acetone; not detectable by conductive sensors

Alta temperatura >90°C: Adopt VPP series (up to 100°C) or high-temperature versions

Pressione di esercizio >10 sbarra: Special high-pressure level sensor required

Strong corrosive media: Concentrated hydrochloric acid, concentrated sulfuric acid; use VPP series with PVDF electrodes or anti-corrosion coated models

6. Installazione & Linee guida per il cablaggio

Requisiti di installazione

1. Posizione di montaggio: Install on tank top or side, away from inlet ports and agitators; ensure vertical electrode immersion
2. Electrode Cutting: Cut electrode length on-site according to actual liquid level; deburr the end after cutting for accuracy
3. Sigillatura: Use suitable gaskets (PTFE recommended) for leak-tight installation to maintain IP67 protection
4. Earthing Requirement: Conductive tank body can serve as common electrode; non-conductive tanks require separate common electrode grounding
5. Spacing Requirement: Keep ≥50mm between electrodes and between electrodes and tank wall to avoid signal interference

Definizione del terminale principale

Punti chiave della messa in servizio

1. Electrode Setting: Define corresponding level heights for each electrode (per esempio. E1=Low, E2=Medium, E3=High, E4=Ultra-high)
2. Regolazione della sensibilità: Adjust amplifier relay sensitivity to avoid false triggering caused by foam or clinging liquid
3. Prova di funzionalità: Simulate level changes to verify accurate switching action and response time
4. Insulation Check: For non-insulated type, ensure no short circuit between electrodes and tank wall; check insulation integrity for insulated type
5. Environmental Adaptation Test: Verify long-term stability within rated temperature and pressure range
6. Regole di selezione & Riferimento rapido

Linee guida per la selezione

1. Liquid Type: Choose VNY series for conductive liquids; use capacitive or ultrasonic sensors for non-conductive liquids
2. Electrode Quantity: 1=single point, 2=high/low, 3=high/medium/low, 4=four-point full control
3. Electrode Insulation: NS for normal liquids; IS insulated type for viscous wall-adhering media
4. Tipo di connessione: NT screw terminal for vibration environments; CB cable type for long-distance installation
5. Filettatura di montaggio: 1 1/2″ for large tanks, 1″ for medium, 1/2″ for small containers
6. Temperatura & Pressione: VNY for 0–90°C / 10 sbarra; VPP for higher temperature; special models for higher pressure
7. Conformità del trasporto aereo & Certificazioni

Conformità del trasporto aereo: Nessuna batteria al litio / supercondensatore. Pure mechanical and metallic structure, conforme alla classe IATA DGR 9, shippable as standard general cargo.

Certificazioni:

– CE: Conforme alla norma CEI 529 ingress protection standard

– RoHS: Conformità RoHS UE, esente da metalli pesanti pericolosi

– Material Certification: AISI316 stainless steel electrodes meet food-contact grade requirements for food & industria delle bevande

Conformità ambientale: Compliant with REACH regulations for global market access

9. Acquisto & Informazioni logistiche