Serie: Modicon X80 32-point Sourcing Transistor Digital Modulo di uscita, Conformal Coated (Severe Environment Version)
Corresponding standard non-coated version: BMXDDO3202K
✅ Spiegazione del codice modello
BMX: X80 I/O Series
DDO: Digital Discrete Output
32: 32 canali
02: 24VDC transistor output
K: Sourcing type (Positivo / Current Source)
C: Rivestimento conforme (anti-corrosion, a prova di umidità, dust-proof for severe environments)
📌 Core Electrical Specifications
Tipo di uscita: Sourcing transistor (PNP, positive logic)
External supply: 24VCC, range 19~30VDC
Rated current per channel: 0.125UN (nominal 0.1A)
Maximum total module current: 3.2UN
Off-state leakage current: ≤0.1mA
On-state voltage drop: <1.5V
Tempo di risposta dell'uscita: 1.2SM
Channel parallel connection: Consentito, massimo. 3 channels in parallel
Consumo energetico: 3.6W
Backplane 3.3V current draw: ca. 125mA
Isolamento: 500VCC, insulation resistance >10MΩ
Protezione: Protezione da inversione di polarità, sovratensione, current limiting; 2A external fast fuse recommended for each group against short circuit
Connettore: 1 × 40-pin FCN flat cable connector (no built-in terminal block, requires matched FCN40 cable)
🧱 Mechanical & Ambientale
Dimensioni: W32 mm × H100 mm × D86 mm
Peso netto: 0.11 kg
Classe di protezione: IP20 (module only, montato su armadio)
Temperatura operativa: 0 ~ +60℃ (coated version, suitable for high-humidity, polveroso, salt-spray environments)
MTBF: ca. 290,000 ore
Certificazioni: CE, UL, CSA, UKCA, EAC, RCM, marine classification certification
🤖 PLC Compatibility
Modicon M340 (local rack / X80 remote I/O)
Modicon M580 (local rack / X80 remote I/O, ePAC)
⚠️ Selection Comparison
| Modello | Rivestimento | Tipo di uscita |
| BMXDDO3202K | Standard, no coating | 32 × 24VDC sourcing transistor |
| BMXDDO3202KC | Rivestimento conforme (C) | 32 × 24VDC sourcing transistor |
🛠️ Typical Application & Note
- Suitable for driving DC24V indicators, piccoli relè, bobine di solenoidi (observe single-channel current limit)
- Wiring only via 40-core FCN flat cable; incompatible with regular terminal bases directly
- Transistor output cannot drive AC loads, nessun contatto meccanico, not suitable for high-frequency large inductive loads. Freewheeling diode in reverse parallel is mandatory for inductive loads
- Coated version for water treatment, minerario, marino, outdoor cabinets and other high-humidity corrosive scenarios
- Matched FCN40 Factory Cables
Cables are fully interchangeable between BMXDDO3202KC and BMXDDO3202K, 40-pin Fujitsu FCN connector
1) Flying-lead type (strip wires directly to cabinet terminals)
BMXFCW303: 3M, 40-nucleo, pre-stripped colour-coded wires split into 2 gruppi di 20
BMXFCW503: 5M
BMXFCW1003: 10M
2) With ABE7 Telefast terminal base (HE10 dual connector, most common for engineering)
One BMXDDO3202KC requires 2 pcs of ABE7 16-point bases
BMXFCC053: 0.5M
BMXFCC103: 1M
BMXFCC203: 2M
BMXFCC303: 3M
BMXFCC503: 5M
BMXFCC1003: 10M
Common ABE7 bases for reference:
ABE7H16C10, ABE7R16S111, ABE7R16T111 (16-point sourcing DC output terminal blocks)
Osservazione: Third-party compatible FCN40 cables (MISUMI, Weidmüller etc.) are available on market. Confirm specs before purchase: Fujitsu FCN-40P male, 0.14mm², 24A DC
- I/O Address Mapping (M340/M580, Unità Pro / EcoStruxure Control Expert)
The module occupies 2 output words (%QW), totale 32 bit
Channels Q00~Q15 → %QWx.0 ~ %QWx.15 (1st word)
Channels Q16~Q31 → %QW(x+1).0 ~ %QW(x+1).15 (2nd word)
Automatic rack allocation rule:
M340 local rack: Allocated sequentially by slot after CPU; X80 remote I/O racks follow scanner configuration order.
Channel-level diagnostics supported; cortocircuito / overload status word can be read in the program.
- Pinout Summary (FCN40 connector, PNP sourcing)
1~20: Q00~Q15 outputs + grouped supply SPS+, SPS-
21~40: Q16~Q31 outputs + grouped supply SPS+, SPS-
Module internally divided into 2 independent supply banks of 16 canali ciascuno. Independent 2A fast fuse per bank recommended. Per carichi induttivi (solenoidi, relè), connect reverse freewheeling diode (1N4007) across coil terminals.
- Elenco di controllo per la risoluzione dei problemi
- RUN LED off
Poor backplane bus contact: Re-seat module, check rack latches; test in alternative slot
Insufficient backplane power; rack power supply undersized
Hardware module damage (coated version less prone to corrosion failure; check backplane first)
- RUN LED ON, channel LEDs do not follow program output
Confirm PNP sourcing wiring: Negative terminal of load to 24V-, output provides +24V
Loss of external SPS supply, blown fuse (failure of half channels usually means fuse blown for that bank)
Wrong program address, forced value or interlock blocking output
- Channel LED ON but load not actuated
On-state voltage drop>1.5V: Short circuit at load, burnt channel; measure channel voltage to GND
Corrente di dispersione: Dim glow at OFF state is inherent transistor leakage (≤0.1mA, common for small indicators)
- Repeated channel fault / burnt channels
Missing freewheeling diode for inductive loads, breakdown by back EMF
Single-channel current over 0.125A; total module current exceeds 3.2A limit
Reverse polarity of external 24V supply, high voltage intrusion
- Special notes for humid/corrosive environments (KC coated version)
Conformal coating protects PCB only; not resistant to condensation or liquid ingress. Cabinet temperature control and dehumidification required
FCN connector pins vulnerable to salt spray oxidation; apply contact protection spray on connectors
- Opzioni di sostituzione (Same-platform / Domestic PLC replacement)
✅ Direct Schneider sostituzione della stessa piattaforma (no program change, no base modification)
Standard non-coated version: BMXDDO3202K (only without conformal coating, parametri elettrici identici)
Avvertimento: Do not replace KC directly with K for humid / salt-spray / mining environments, service life will be drastically reduced
✅ Domestic alternatives (complete PLC replacement, incompatible with X80 backplane, è richiesta la migrazione del programma)
Selection criteria: 32-point 24VDC PNP sourcing transistor output, 0.1Uno per canale, with channel diagnostics
Common options:
- Innovazione: AM600 series AM600-32DO (PNP, check revision)
- Xinje: XD/XG series 32-point DO module
- HCFA: HC-A0/HC-Q series 32-point transistor output
- HollySys: LX series 32DO sourcing module
Important reminder: Domestic modules have no FCN40 port, terminal-block design only. If existing FCN wiring harness is retained, domestic modules cannot be used for direct swap; only Schneider X80 applies.
- Additional Maintenance Notes
Parallel channels allowed: Massimo. 3 channels in parallel for higher drive current
Tempo di risposta: 1.2SM, not suitable for high-speed pulse / PWM output
Magazzinaggio: Coated modules resist corrosion, but avoid high temp & humidity for long-term storage; sealed moisture-proof storage recommended
BMXDDO3202KC Full Technical Datasheet (Ufficiale Schneider)
Serie: Modicon X80; Tipo: 32-point 24VDC sourcing (PNP) transistor digital output module; C = Conformal Coated Severe Environment Version
- Informazioni di base
Modello: BMXDDO3202KC
CPU compatibili: Modicon M340 / M580 (local rack, X80 remote I/O station)
Conteggio canali: 32 FARE, split into 2 banks × 16 independent supply domains
Tipo di uscita: Solid-state transistor, Positive Sourcing (PNP)
Standard: EN/IEC 61131-2
Interfaccia: 40-pin Fujitsu FCN flat cable interface, no built-in terminal block
- Electrical Output Ratings
External supply SPS: DC24V, 19V~30 V CC
Rated continuous current per channel: 0.1UN; limite attuale: 0.125UN
Max total module output current: 3.2UN
Off-state leakage current: ≤0.1mA
On-state voltage drop: <1.5V
Tempo di risposta dell'uscita: 1.2 SM
Parallel channels: Consentito, massimo. 3 channels in parallel
Protezione da sovraccarico: Built-in current limiting + viaggio elettronico, overload range 0.125~0.185A
Protezione da cortocircuito: On-board current limiting, external 2A fast fuse required for each 16-channel bank
Protezione da sovratensione: Transil transient suppressor diode; reverse protection: reverse diode
Isolamento: 500VCC, insulation resistance>10MΩ
Fault detection threshold: >18V DC = normal; <14V DC = upstream supply fault alarm
Consumo energetico tipico: 3.6W
Backplane 3.3V bus consumption: Typical 125mA
- Diagnostica & Indicatori
RUN green: Module healthy
ERR red: Module fault / bus fault
Independent green LED per channel: Indicazione dello stato del canale
Channel-level diagnostics supported: Cortocircuito, sovraccarico, external supply loss; fault word readable in CE/Unity Pro
- Specifiche meccaniche
Dimensioni: W32 mm × H100 mm × D86 mm
Peso netto: 0.11 kg
Classe di protezione: IP20 (module only, cabinet use)
PCB treatment: Rivestimento conforme (umidità, mould and salt spray resistant)
- Valutazioni ambientali
Temperatura operativa: 0 ℃ ~ +60 ℃
Temperatura di conservazione: -40 ℃ ~ +85 ℃
Umidità relativa: 5% ~ 95%, senza condensa (coating does not stop condensation or water ingress)
MTBF: 312,254 ore (riferimento)
Certificazioni: CE, UL, CSA, UKCA, EAC, RCM, certificazione marina
- Software Address Assignment
Output occupancy: 2 %QW words (QWx, QWx+1), totale 32 bit
Q0~Q15 → QWx bit0~bit15
Q16~Q31 → QWx+1 bit0~bit15
- Comparison with Non-coated Sibling Model
BMXDDO3202K: Identical electrical specs, no conformal coating, standard indoor environment only
BMXDDO3202KC: Conformal coated, for mining, trattamento dell'acqua, marino, high-humidity salt-spray cabinets
- Limitazioni critiche (Engineering Focus)
- Uscita a transistor, nessun contatto, cannot drive AC loads. Freewheeling diode mandatory for inductive loads
- Not designed for high-speed pulse / PWM output
- Two banks of 16 channels with isolated supplies; blown fuse only impacts that bank of 16 punti
- Only compatible with FCN40 cables (BMXFCW/BMXFCC series); direct connection to generic terminals not supported
Schneider Modicon X80 (M340/M580) Digital Output DO Module List
Code definition:
DDO: Solid-state DC transistor output; DRA/RDC: Uscita relè; DAO: Triac AC output
K = Sourcing PNP; 12 = Sinking NPN; C = Conformal coating Severe; H = Wide temp + rivestimento conforme; suffix H = severe environment grade
Interface classification: Direct terminal / FCN flat cable (requires ABE7 terminal base + FCW/FCC cable)
- DC Transistor Output (BMXDDO Series, 24VCC)
| Modello | Punti | Tipo | Current per Channel | Interfaccia | Osservazioni |
| BMXDDO1602 | 16 | Sourcing PNP | 0.625UN | 20-pin direct terminal | Standard high-current transistor |
| BMXDDO1602H | 16 | Sourcing PNP | 0.625UN | 20-pin direct terminal | Wide temp coated severe -25~70℃ |
| BMXDDO1612 | 16 | Sinking NPN | 0.125UN | 20-pin direct terminal | Standard sinking |
| BMXDDO1612H | 16 | Sinking NPN | 0.125UN | 20-pin direct terminal | Wide temp coated sinking |
| BMXDDO3202K | 32 | Sourcing PNP | 0.125UN | FCN40 flat cable | Standard non-coated base version |
| BMXDDO3202KC | 32 | Sourcing PNP | 0.125UN | FCN40 flat cable | Conformal coated severe (your target model) |
| BMXDDO6402K | 64 | Sourcing PNP | 0.125UN | Dual FCN40 flat cable | Standard non-coated 64pt |
| BMXDDO6402KC | 64 | Sourcing PNP | 0.125UN | Dual FCN40 flat cable | Conformal coated 64pt severe |
- Uscita relè (DRA / Repubblica Democratica del Congo, Compatibile AC/DC)
Relays suited for AC220V loads; DRC = fast relay, DRA = standard relay
| BMXDRA0804T | 8 | 100~150VAC | Isolated contacts | Modello legacy |
| BMXDRA0805 | 8 | 24VCC / 24~240 VCA | Independent relay | Obsoleto, solo pezzi di ricambio |
| BMXDRA0805H | 8 | 24VCC / 24~240 VCA | Independent relay | Coated severe |
| BMXDRA0815 | 8 | 24VCC / 24~240 VCA | Independent relay | Regular active model |
| BMXDRA0815H | 8 | 24VCC / 24~240 VCA | Independent relay | Coated severe |
| BMXDRA1605 | 16 | 24VCC / 24~240 VCA | Independent relay | Popular 16pt relay DO |
| BMXDRA1605H | 16 | 24VCC / 24~240 VCA | Independent relay | Coated severe |
| BMXDRC0805 | 8 | 24VCC / 24~240 VCA | High-speed relay | Faster operation |
| BMXDRC0805H | 8 | 24VCC / 24~240 VCA | High-speed relay | Ad alta velocità + coated |
- Triac AC Output (DAO, AC loads only)
| Modello | Punti | Valutazione | Osservazioni |
| BMXDAO1605 | 16 | 48~240 VCA, 0.5UN | Solid-state AC output, nessun contatto, for AC lamps, riscaldatori |
| BMXDAO1605H | 16 | 48~240 VCA, 0.5UN | Coated severe |
- I/O misti (DI+DO, common for engineering selection)
| Modello | DI | FARE | Tipo di uscita |
| BMXDDM16025 | 8DI | 8FARE | Uscita relè |
| BMXDDM16025H | 8DI | 8FARE | Relè, coated version |
| BMXDDM3202K | 16DI | 16FARE | 24VDC sourcing transistor, FCN cable |
✅ Quick Selection Cheat Sheet
- Direct terminal (20-spillo): BMXDDO1602 / 1612 serie, hardwire directly, no FCN cable needed
- FCN flat cable type: 32pt, 64pt (3202K / KC, 6402K / KC), must use BMXFCW/BMXFCC cable + ABE7 terminal block
- Difference between C and H
C: PCB conformal coating only, temp 0~60℃ (BMXDDO3202KC)
H: Rivestimento conforme + wide temperature -25~70℃ (1602H,1612H, DRAxxH)
- Transistor outputs cannot drive AC; relay and DAO triac support AC loads
Contattore,interruttore automatico,sensore,Codificatore,PLC,Convertitore























NH42-63-318x560.png)



