コンタクタ,サーキットブレーカー,ソーラーインバーター,電気メーター,太陽電池
モデルコードの定義
| セグメント | コード | 意味 |
| G2R | – | 製品シリーズ: General-purpose Power Relay |
| 0.5 | – | Contact pole: 1-pole SPDT (10あ) / 2-pole DPDT (5あ) |
| -S | – | Terminal type: プラグイン, matched with 8-pin socket |
| -N | – | 関数: Built-in LED operation indicator |
| -D | – | 関数: Built-in coil surge suppression diode (DC coil only) |
| -私 | – | 関数: With lockable test button, manual actuation for circuit inspection |
| (S) | – | Extra function: Standard mechanical indicator and nameplate for model & purpose marking |
| DC24/AC220 | – | Rated coil voltage, specify upon order; AC and DC cannot be mixed |
記憶規則: G2Rシリーズには以下のものが含まれます 1/2 極. SNDIはLEDを統合します, フリーホイールダイオードとテストボタン. (S) メカニカルインジケーターと銘板を装備. 正しいAC/DC電圧を選択してください.
- Core Specification Table (モデル: G2R-2-SNDI DC24 (S))
| カテゴリ | パラメータ | 備考 |
| 基本仕様 | ||
| Relay Type | Plug-in miniature power relay | IEC準拠 61810-1 |
| 接点構成 | 2c DPDT / 1c SPDT | 8 pins for 2-pole, 5 pins for 1-pole |
| 定格荷重 | 2-ポール: 5A @ 250VAC / 5A @ 30VDC | 抵抗負荷; derate for inductive load |
| 1-ポール: 10A @ 250VAC / 10A @ 30VDC | ||
| Inductive Load Capacity | 2-ポール: 2A @ 250VAC / 0.5A @ 30VDC | Power factor 0.4, L/R=7ms |
| 1-ポール: 7.5A @ 250VAC / 5A @ 30VDC | ||
| Max Switching Power | 2-ポール: 2500バージニア州(交流) / 300W(直流) | |
| 1-ポール: 3000バージニア州(交流) / 300W(直流) | ||
| Contact Resistance | ≤50mΩ (DC5V 1A voltage drop method) | Initial value |
| コイルパラメータ (DC24V) | ||
| 定格電圧 | DC24V | Allowable fluctuation: ±10% |
| 定格電流 | 21.6ミリアンペア | |
| コイル抵抗 | 1113おお | 20℃で測定 |
| Coil Inductance | 約. 3.6H | Reference value |
| ピックアップ電圧 | ≤75% 定格電圧 (Max DC18V) | |
| ドロップアウト電圧 | 定格電圧の10%以上 (Min DC2.4V) | |
| 機械式 & 電気的性能 | ||
| 動作時間 | ≤15ms (excluding contact bounce) | |
| リリースタイム | ≤20ms (diode built-in type) | Standard type ≤10ms |
| Max Operation Frequency | 機械式: 18,000 cycles/hour | |
| 電気: 1,800 cycles/hour under rated load | ||
| Insulation Resistance | ≥1000MΩ (DC500V megohmmeter) | Between coil and contact |
| 絶縁耐力 | Coil to contact: 2000VAC 1min | 50/60Hz |
| Between contacts: 1000VAC 1min | ||
| Between coils: 500VAC 1min | ||
| 環境 & 物理的特性 | ||
| 動作温度 | -40℃～+70℃ | 結露なし |
| 保管温度 | -40℃～+85℃ | |
| 湿度 | 35% ～ 85% RH | 結露なし |
| 重さ | 約. 20g | |
| 取付タイプ | Matched with P2RF series sockets, recommended P2RF-08-PU Push-In Plus socket | 60% wiring time saved |
| テストボタン | Lockable type (lockable at ON position) | Circuit inspection without power supply |
- Full Model List SNDI Type (G2R-□-S (S) シリーズ)
3.1 1-pole Models (G2R-1-SNDI (S))
| モデルプレフィックス | 機能の説明 | オプションの電圧 | Order Example |
| G2R-1-SNDI | LED indicator + built-in diode + lockable test button | AC12/24/100/110/200/220V | G2R-1-SNDI DC24 (S) |
| DC6/12/24/48/100V | |||
| G2R-1-SNI | LED indicator + lockable test button (no diode) | 同上 | G2R-1-SNI AC220 (S) |
| G2R-1-SND | LED indicator + built-in diode (no test button) | 同上 | G2R-1-SND DC12 (S) |
| G2R-1-SN | Only LED indicator | 同上 | G2R-1-SN AC110 (S) |
| G2R-1-S | 標準タイプ (no LED/diode/test button) | 同上 | G2R-1-S DC48 (S) |
3.2 2-pole Models (G2R-2-SNDI (S))
| モデルプレフィックス | 機能の説明 | オプションの電圧 | Order Example |
| G2R-2-SNDI | LED indicator + built-in diode + lockable test button | AC12/24/100/110/200/220V | G2R-2-SNDI DC24 (S) |
| DC6/12/24/48/100V | |||
| G2R-2-SNI | LED indicator + lockable test button (no diode) | 同上 | G2R-2-SNI AC220 (S) |
| G2R-2-SND | LED indicator + built-in diode (no test button) | 同上 | G2R-2-SND DC12 (S) |
| G2R-2-SN | Only LED indicator | 同上 | G2R-2-SN AC110 (S) |
| G2R-2-S | 標準タイプ (no LED/diode/test button) | 同上 | G2R-2-S DC48 (S) |
3.3 特別モデル
| モデル | 特別な機能 | 応用 |
| G2R-2-SNDI-AP3 | AP3 certified, compliant with UL508 | Industrial control for North America |
| G2R-1-SNDI-G | Gold-plated contact | Low-level signal switching ≤100mA |
- Cross-brand Replacement List
| Omron Model | 代替ブランド | 代替機種 | 主な違い |
| G2R-2-SNDI DC24 (S) | シュナイダー | RXM2AB2BD + test button accessory | Extra test button needed, 同様の価格 |
| シーメンス | 3RT1015-1BB42 + locking test unit | Larger dimension, different contact material | |
| ABB | CR-MX024DC2L + test module | 同一の取り付け, より高い価格 | |
| ワイドミュラー | DRM57024 + manual test switch | Different terminal design, external test function | |
| Domestic brand | YHRJ2S-CL DC24V + テストボタン | 費用対効果の高い, consistent performance, optional test button | |
| G2R-1-SNDI DC24 (S) | シュナイダー | RXM4AB2BD + test accessory | 10A 1-pole capacity, extra test part required |
| シーメンス | 3RT1016-1BB42 + test device | 12A 1-pole capacity, complete test function |
選択の提案: Prioritize Omron for integrated design. Choose domestic alternatives for cost control. Match original brand for system compatibility.
- 一般的な障害 & ソリューション
| 故障現象 | 考えられる原因 | ソリューション |
| コイル断線 | 1. Mixed AC/DC voltage | 1. Verify AC/DC marking |
| 2. Voltage exceeds 卤10% rated value | 2. Keep voltage within rated range | |
| 3. Reversed DC coil polarity | 3. Wire per +/- terminal marking | |
| No contact actuation after power-on | 1. Test button locked at ON | 1. Switch test button to OFF |
| 2. Voltage lower than 75% rated value | 2. Raise voltage over 80% rated value | |
| 3. Mechanical jam & unreset button | 3. Confirm full reset of test button | |
| No response in manual test | 1. Damaged test button | 1. リレーを交換する |
| 2. Mechanical blockage | 2. Check mounting and socket tightness | |
| 3. 接触溶接 | 3. Replace relay and inspect overload | |
| LED off while relay operates | 1. Broken LED | 1. リレーを交換する |
| 2. Burnt current-limiting resistor | 2. Check circuit overcurrent | |
| 3. Reversed DC polarity | 3. Correct coil wiring polarity | |
| Failure to reset after power cut | 1. Locked ON test button | 1. Reset test button |
| 2. Residual coil voltage | 2. Add discharge circuit or replace coil | |
| 3. 接触溶接 | 3. Replace relay and check load type |
予防: Reset test button properly. Do not mix AC and DC. Correct polarity wiring. Add absorption circuit for inductive load. Do not exceed rated current.
- 航空貨物のコンプライアンス & 認証
6.1 航空貨物のコンプライアンス
| アイテム | 状態 | 説明 |
| Built-in lithium battery/supercapacitor | なし | Electromagnetic relay without energy storage components |
| Magnetic property | Weak magnetism | Compliant with IATA DGR Class 9 unrestricted goods |
| Shipping category | General cargo | No UN number required |
| 包装 | Standard anti-static package | Avoid impact to prevent component damage |
6.2 認証
| Certificate | 標準 | Compliance Status |
| CE | LVD 2014/35/EU + EMC 2014/30/EU | Compliant |
| RoHS | RoHS 2.0 10-substance restriction | Lead & cadmium free eco-design |
| UL | UL508 Industrial Control Equipment | Optional for partial models (-AP3 suffix) |
| CSA | C22.2 No.14 Canadian Standard | Synchronized with UL certification |
| IEC | IEC 61810-1 General Relay Standard | Compliant |
Export Notice: Provide CE & RoHS documents for EU market. Select UL/CSA certified models with -AP3 suffix for North America.
- Application Cases & Industry Matching
7.1 典型的なアプリケーションシナリオ
| 業界 | 応用 | 選定のポイント |
| 産業オートメーション | PLC output expansion, drive solenoid valves, 小型モーター, contactor coils | DC24V G2R-2-SNDI(S) with P2RF-08-PU socket for convenient circuit test |
| ビルディングオートメーション | HVAC control, ファン & water pump startup, 照明制御 | AC220V G2R-1-SNDI(S), mechanical indicator for on-site maintenance |
| Equipment Manufacturing | Signal switching for test, medical and semiconductor devices | DC12V G2R-1-SNDI-G(S) gold-plated contact for reliable low-level signal |
| エネルギー産業 | Control loop of solar inverter & UPS | DC48V G2R-2-SNDI(S), built-in diode for surge suppression |
| 鉄道交通 | Auxiliary vehicle system, door & air conditioning control | DC24V G2R-1-SNDI(S), shock resistance, easy maintenance test |
7.2 Case Analysis
Case Title: PLC Control Circuit Test Optimization for Auto Parts Production Line
要求: Frequent fault inspection; traditional powered test is inefficient and risky
選択: G2R-2-SNDI DC24 (S) + P2RF-08-PU Push-In Plus Socket
効果:
- Lockable test button realizes manual actuation without power, 30% efficiency improved
- デュアルLED & mechanical indicator reduces misjudgment
- Built-in diode suppresses back EMF and protects PLC modules
- Push-In Plus socket cuts wiring time by 60% and lowers installation cost
- Nameplate marking facilitates circuit management
- 選択ルール & まとめ
選択のヒント
- Choose poles by load: 1-pole 10A for heavy load, 2-pole 5A for dual circuit
- Identify functions by suffix: Integrated LED, diode and test button; (S) with mechanical indicator
- Confirm voltage: No AC-DC interchange, pay attention to DC polarity
- Match P2RF socket series to save wiring labor
- Lockable test button enables offline circuit inspection
主な利点
All-in-one design with complete indicators and test functions
Easy installation and remarkable wiring efficiency improvement
Convenient offline fault diagnosis
Effective surge protection prolongs service life
Eco-friendly wide temperature range from -40°C to +70°C
