Schneider 3-pole main contacts LC1D38BD

Schneider TeSys Deca series, 3-극 주요 접점, 24VDC 코일. Designed for motor start/stop, HVAC and automation control cabinets. Built-in 1NO+1NC auxiliary contacts.

✅ Model Code Definition

LC1: 표준 접촉기

디: 테시스 D (데카) 시리즈

38: Rated operational current 38A @ AC-3, 400다섯

BD: 24V DC 코일 (integrated coil surge suppression)

📌 Key Electrical Specifications

🛠️ Typical Applications

직접 온라인, star-delta and forward/reverse control of 3-phase asynchronous motors

HVAC 시스템, 물 펌프, 팬, 공기 압축기

자동화 장비, packaging machinery and production line control cabinets

Direct coil drive by PLC 24VDC digital outputs (no intermediate relay required)

🧩 Compatible Accessories

열과부하 계전기: LRD 시리즈 (LRD35…), snap-fit directly below the contactor

Auxiliary contact block: LA1DN (for extra NO/NC contacts)

기계적 인터록 모듈: LA9D4001 (for forward/reverse interlock)

서지 억제: Integrated inside coil, no external component needed

🔁 Alternative & Compatible Selection

1. AC coil variants within the same series: LC1D38M7 (220VAC), LC1D38B7 (24VAC)
2. 국내 대안: CJX2-3811 DC24V (note differences in dimension, terminals and mechanical life)

⚠️ 중요: BD = 24VDC, B7 = 24VAC. Coils are NOT interchangeable.

📋 Certifications & 표준

IEC 60947-1/-2/-4-1, CCC, cULus. Complies with IEC60335-1 flame retardant standard and A2L refrigerant safety certification for HVAC.

🧪 Second-hand Inspection Checklist

1. 코일: Continuity check on A1/A2. Apply 24VDC; armature pulls in without noise or overheating.
2. 주요 연락처: L1/L2/L3 ↔ T1/T2/T3. Conductive when closed, high resistance when open; inspect contact erosion.
3. 보조 접점: 13-14(아니요), 21-22(NC). Switch synchronously with main contacts.
4. 기계: 달라붙지 않음; housing free of cracks or carbon blackening.

HS Code Reference

8536410000 (Electromagnetic contactor, voltage ≤60V)

Typical Engineering Application Cases for LC1D38BD

핵심 장점: DC24V 코일, direct PLC drive without intermediate relay; built-in surge suppression and certified mirror NC contact; 18.5kW max 3-phase motor @ AC-3, 50A for AC-1 resistive loads

사례 1: Chilled water pump DOL start for HVAC BMS (빌딩 자동화 시스템)

짐: 15kW 3-phase chilled water pump, 380다섯, motor rated current ≈28A

Control scheme: PLC (지멘스 / Schneider M241) DO directly drives LC1D38BD 24VDC coil

주회로: 3P circuit breaker → LC1D38BD → LRD35 thermal overload relay → pump motor

제어 논리: BMS outputs 24VDC based on water temperature/pressure differential to energize contactor and start pump. Built-in 1NO auxiliary contact feeds running status back to PLC; built-in mirror NC contact for fault acquisition.

Selection rationale: DC coil provides strong anti-interference. BMS cabinets commonly adopt DC24V control. Wide temperature range -5~+60℃ suits high-temperature equipment rooms. 45mm narrow body saves cabinet space.

부속품: LRD35 thermal relay (28~36A), DIN 레일 장착.

사례 2: Air compressor motor control (OEM machinery manufacturer)

짐: 18.5kW screw air compressor main motor, 400다섯

Control scheme: PLC directly drives LC1D38BD with pressure switch interlock for shutdown

회로: Circuit breaker → LC1D38BD → LRD thermal relay → air compressor motor

특징: 빈번한 시작-중지 (최대 3600 주기/시간). DC coil pulls in stably without AC hum. Built-in coil surge suppression protects PLC output points against back EMF.

메모: AC-3 operation reaches the 38A rating limit. Derating evaluation is recommended for heavy-duty frequent cycling.

사례 3: Water treatment — duty/standby mutual interlock control cabinet for sewage lift pumps

짐: Two 15kW sewage pumps, duty-standby auto-switching by liquid level

구성: 2 × LC1D38BD + LA9D4001 mechanical interlock module

논리: Pump starts on high liquid level. If main pump trips (thermal relay fault), PLC automatically switches to standby pump. Mechanical interlock prevents simultaneous closure and short circuit.

Safety feature: Built-in mirror NC contact for safety loop and fault diagnosis, meeting water treatment control cabinet safety specifications.

애플리케이션: Municipal sewage, factory circulating water, rainwater lift pumping stations.

사례 4: Forward/reverse circuit for conveyor motors in packaging machinery / 생산 라인

짐: 11~15kW belt conveyor motor requiring forward and reverse rotation

구성: 2 × LC1D38BD (KM1 forward, KM2 reverse) + LA9D4001 mechanical interlock

제어: PLC 24VDC digital outputs drive each contactor coil separately. 전기적 인터록 (using built-in NC auxiliary contacts) plus mechanical interlock provides double protection to prevent power short circuit.

이점: DC coil has better EMI immunity than AC coils in workshops dense with inverters and sensors, reducing accidental pull-in faults.

사례 5: Star-delta reduced voltage starting for 18.5kW dust extraction fan

짐: 18.5kW dust removal fan with high inrush current, star-delta starting adopted

구성: 3 × LC1D38BD, serving as main contactor, star contactor and delta contactor respectively

논리: PLC outputs 24VDC sequential control; star reduced-voltage start first, then time-delayed switch to delta full-voltage operation. Built-in contactor auxiliary contacts provide status feedback and electrical interlock.

메모: High inrush current occurs at delta switching in star-delta circuits; contact life must be reviewed.

사례 6: AC-1 저항 부하: Industrial heating module control

짐: 3-phase heating elements, total resistive load ≤33kW (AC-1 50A @400V)

특징: Resistive load has no starting inrush current. AC-1 rated 50A capacity higher than motor duty. PLC 24V DO directly controls heating circuit on/off.

애플리케이션: Ovens, constant temperature units, process heating equipment.

사례 7: Cleanroom air handling unit for medical facilities (medical HVAC)

짐: 15kW supply air fan for operating room clean air conditioning

특징: Medical equipment demands high reliability and low EMI. LC1D38BD DC coil with built-in surge suppression, no electromagnetic noise from AC coils. Complies with IEC60335 HVAC safety standard, suitable for A2L refrigerant HVAC equipment, widely used in hospital BMS control cabinets.

General Selection & Construction Key Points (Valid for All Cases)

1. DC coil critical note: BD = 24VDC, MUST NOT be connected to AC24V. PLC output capacity must meet coil power consumption (~15VA).
2. 보조 접점: Built-in 1NO (running feedback) +1NC (mirror safety contact, NOT for normal latching). Add LA1DN auxiliary contact block for more contacts.
3. 과부하 보호: Must be fitted with LRD thermal overload relay, set per motor nameplate current and shall not exceed motor rated current.
4. Utilisation category distinction

AC-3 (normal motor start-stop): 38에이, max 18.5kW @400V

AC-1 (pure resistive heating): 50에이

AC-4 (frequent jogging, plug braking): 디레이팅 필요

Not Suitable Applications

Direct-on-line starting of 3-phase motors above 18.5kW (AC-3)

High-power capacitor switching (use dedicated LC1DxxKQ capacitor contactors)

폭발 위험 지역 (explosion-proof series required)

LC1D38BD (TeSys D DC Coil) 개요 & 장착 치수

Without attached accessories (보조 접점, 열 릴레이, 기계적 인터록), DC coil version

Outline Dimensions (폭 × 높이 × 깊이)

45 mm × 85 mm × 92 mm

너비: 45mm (DIN rail module, 1 module unit)

키: 85mm

깊이: 92mm (from mounting backplate to front face)

Panel screw mounting holes (DC coil specific, round holes for M4)

Horizontal center distance between two holes: 35 mm

Vertical center distance between two holes: 70 mm

Screw size: M4, two round holes (⚠️ AC coil LC1D38M7 uses slotted holes; mounting layout differs from BD DC version)

레일 장착

표준 35mm DIN 레일과 호환 가능 (TH35-7.5), clip-on installation, no drilling required.

Cabinet Layout Recommendations

1. Mounting LRD thermal relay at bottom: overall height increases; reserve adequate clearance.
2. Mounting LA1DN auxiliary contact block on top: extra depth and height required.
3. Multiple contactors side-by-side: 45mm 폭, can be mounted tightly on rail without gap. Reserve heat dissipation gap for high-temperature environments.

Operating Principle of Schneider LC1D38BD Contactor

LC1D38BD is an electromagnetic contactor with DC coil (테시스 D 시리즈). Essentially, it is a remotely controlled electrical switch driven by 24VDC electromagnet, using low DC signal to switch high-power 3-phase main circuit.

1. 기본 구조
2. Electromagnetic actuation section (코일 A1/A2): 24V DC excitation coil, fixed core, moving armature, 복귀 스프링
3. 주요 연락처 (power circuit L1/L2/L3 → T1/T2/T3): 3 pairs of normally-open main contacts, rated 38A AC-3, carrying high current for 3-phase motors / heating loads
4. 보조 접점 (신호 피드백): Built-in 1NO (13-14)+1NC (21-22) mirror auxiliary contacts for status feedback and electrical interlock
5. 아크 챔버: Extinguishes electric arc when main contacts open, protecting contacts from rapid erosion

✅ Key feature for BD model: DC coil with integrated surge suppressor.

2. 전체 작동 순서

2.1 Coil Energized (Pull-in action)

Apply DC24V to A1 and A2 via PLC or external control circuit:

DC coil generates constant magnetic field, magnetizing fixed core, overcoming return spring force and pulling in moving armature.

Armature drives contact carrier synchronously:

3 pairs of main NO contacts close → 3-phase main circuit energized, motor/load powered on

Auxiliary contacts switch simultaneously: 13-14(아니요) 닫는다; 21-22(NC) opens

Characteristic of DC coil: constant current after pull-in, no vibration or hum from AC coils.

2.2 Coil De-energized (Drop-out action)

DC24V control signal removed:

Magnetic field of coil disappears, return spring pulls armature back.

All main contacts open, cutting high-current main circuit.

보조 접점 재설정: 13-14(아니요) opens; 21-22(NC) restores closed state.

Built-in surge suppression absorbs back EMF generated at coil de-energization, protecting upstream PLC output points.

3. Core Differences Between DC Coil (BD) and Conventional AC Coil
4. AC 코일: operates on alternating magnetic field, prone to vibration and hum; high inrush current; contact bounce under voltage fluctuation.
5. LC1D38BD DC24V coil:

Stable magnetic field, armature free of vibration, quiet operation

Pull-in current ≈ holding current, low inrush

Built-in freewheeling suppression, ideal for direct PLC DO drive

불리: Must never connect to AC supply; AC input burns coil immediately.

4. Typical Functions of Auxiliary Contacts

1아니요 (13-14): Running status feedback to PLC to detect contactor pull-in state

1NC (21-22, mirror contact): 안전 회로, fault detection, electrical interlock (forward/reverse circuits)

⚠️ Mirror contact property: NC contact cannot close when main contacts are welded shut, complying with safety circuit requirements.

5. Mandatory Protection Logic for Engineering

The contactor only performs switching and has NO overload protection:

Fit LRD thermal overload relay in main circuit: on motor overload, thermal relay NC contact opens contactor coil circuit to cut motor power.

Circuit breaker installed upstream: fast short-circuit protection for main power supply.

One-sentence summary:

Apply DC24V to A1/A2; electromagnetic force actuates internal contacts to close high-power 3-phase main circuit. Remove 24V supply; spring resets and opens main circuit. Low-voltage 24V signal remotely switches high-power loads. Auxiliary contacts provide status feedback and safety interlock.