SMC IP8000 전기 공압식 밸브 포지셔너 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

위챗: +86-13184948252 왓츠앱: 0086-13811255435 이메일: kent@bestcontactor.com

에 대한 연락하다 |

SMC IP8000 전기 공압식 밸브 포지셔너 - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

전기 같은/

SMC IP8000 전기 공압식 밸브 포지셔너

The IP8000 is a classic SMC mechanical E/P electro-pneumatic positioner (non-smart, 하트 없음). It is designed for linear-stroke pneumatic diaphragm actuators. It receives a 4~20mA current signal and converts it into supply air pressure to drive control valves. It replaces the older IP6000 series. The IP8100 in the same series is for rotary-stroke applications. 그만큼 ...

  • 제품 세부정보

The IP8000 is a classic SMC mechanical E/P electro-pneumatic positioner (non-smart, 하트 없음). It is designed for linear-stroke pneumatic diaphragm actuators. It receives a 4~20mA current signal and converts it into supply air pressure to drive 제어 밸브. It replaces the older IP6000 series. The IP8100 in the same series is for rotary-stroke applications. The IP8001/IP8101 are smart versions with auto-tuning and share the same housing.

✅ 주요 기술 사양

목IP8000 (레버형)
입력 신호DC 4~20mA, Input Resistance: 235±15Ω
Supply Air Pressure0.14~0.7 MPa
Applicable Stroke10~85mm (linear valve stem)
정확성Sensitivity ≤0.1%FS; Linearity ±1%FS; Hysteresis ≤0.75%FS; 반복성 ±0.5%FS
유입 방지IP65 (IEC60529)
주변 온도-20~80℃ for standard model; ExdⅡBT5 explosion-proof: -20~60℃
Air PortsRc1/4 / G1/4 / 1/4NPT; Gauge port Rc1/8
전기 연결G1/2, M20×1.5, 1/2NPT optional
진동 저항No resonance within 5~200Hz
장착 표준Compliant with NAMUR, DIN/IEC 60534-6-1 괄호

😀 모델 코드 정의 (IP8000-□□□)

IP8000: Lever-type mechanical electro-pneumatic positioner

  1. Pressure gauge specification: 0=0.3MPa, 3=1.0MPa
  2. 건설: Standard housing / ExdⅡBT5 explosion-proof terminal box
  3. 부속품: Restrictor pilot valve, yoke linkage, extended feedback lever, 등.
  4. Thread type, CE marking, special custom codes (예를 들어. X310=IP66)

🛠 Working Principle & 설치 지침

  1. 원칙: A 4~20mA current energizes the torque motor. The nozzle-flapper amplifies the signal to control the output air pressure of the pilot valve. The feedback lever captures the actual valve stem position to form a closed loop, ensuring valve position matches the input signal.
  2. Key Installation Rule: ~에 50% 신호 (12엄마), the feedback lever should form a 90° right angle with the valve stem. Select the internal feedback spring according to single-acting or double-acting actuators.
  3. 조정: Mechanical Zero and Span knobs. Supports split range operation. Equipped with manual/auto switching screw for manual air supply during commissioning.

⚠️ 일반적인 문제 해결

  1. Valve fails to move

No supply air or insufficient air pressure; 4~20mA wiring reversed; nozzle/restrictor blocked by dust; torque motor damaged.

  1. Oscillation / 수렵

Incorrect feedback lever mounting angle; unstable supply air pressure; stuck pilot valve; excessive friction of valve packing.

  1. Poor linearity / 제로 드리프트

Zero/span not calibrated; 느슨한 피드백 연결; 공기 배관 누출; 큰 주변 온도 변화.

  1. 출력 압력이 부족함

이물질 막힘 파일럿 밸브; 액츄에이터 다이어프램/실린더 누출; 막힌 공기 필터.

유지보수 알림: 분해하기 전에 공기 공급을 차단하고 압력을 완전히 배출하십시오.. 0.2mm 가는 와이어로 노즐 오리피스를 청소하세요.. O-링을 조립할 때 TORAY SH45 실리콘 그리스를 가볍게 바르십시오..

📋 모델 선택 & 대안

IP8000: 기계, 선형 스트로크 레버. 기존 제어 밸브의 경우, 저렴한 비용, 의사소통 없음.

IP8100: 기계, 로터리 캠, 버터플라이 및 볼 밸브용.

IP8001: 스마트 선형 스트로크. 자동 교정, 수사슴, 결함 진단, IP8000 업그레이드 교체.

국내 대안: Wuzhong, Chuanyi 등 국내 E/P 포지셔너. 브래킷 확인, 공기 포트와 스트로크 매칭.

📎 일반적인 적용 시나리오

지속적인 흐름 조절, 화학 분야 선형 공압 다이어프램 제어 밸브의 압력 및 레벨, 수처리, 공조, 종이, 기름 & 가스 파이프라인. Explosion-proof versions ExdⅡBT5 are available for hazardous areas.

SMC IP8000 Electro-Pneumatic Valve Positioner — Application Scenarios

The IP8000 is a linear-stroke mechanical E/P positioner matching diaphragm linear pneumatic control valves. It converts 4~20mA analog signal into air pressure to drive valve stem for continuous process regulation. No HART communication.

🏭 Industry Applications

  1. 물 / 폐수 처리

Inlet flow regulation, pH dosing line, 액체 레벨 제어, aeration pressure regulation. Standard non-explosion model is sufficient; IP65 preferred for outdoor installation.

  1. 공조 & Heating Networks

Temperature control for primary/secondary side of heat exchangers, regulating steam/hot water linear control valves.

  1. 제지 산업

Pulp concentration control, white water flow, steam pressure regulation. Dust-prone workshop; 노즐 막힘을 방지하려면 공기 여과가 필수입니다..

  1. 화학 산업 (위험지역에는 ExdⅡBT5 방폭 IP8000 사용)

지속적인 흐름 조절, 프로세스 파이프라인의 압력 및 레벨. 용제 및 경질 탄화수소 위험 지역에 필요한 방폭 하우징.

메모: IP8000은 스마트 진단 없이 기계식입니다.. HART 및 자동 조정이 필요한 경우 IP8001을 사용하십시오..

  1. 음식 & 음료 / 제약 (위생 서비스)

정제수, 세척수 및 증기 조절, 위생 선형 제어 밸브와 결합. 깨끗한 계기용 공기를 선호하세요.

  1. 힘 & 화력 발전소

보일러 급수, 과열저감 및 압력 감소, 응축수 레벨 제어; 보조 공정 제어 밸브.

  1. 기름 & 가스 저장 & 운송 (방폭 버전)

원유/제품 파이프라인의 압력 및 유량 조절, 탱크 레벨 제어. 폭발 위험 지역용 Exd 방폭 모델.

✅ 적합한 밸브 유형

단동 / double-acting linear pneumatic diaphragm control valves (best match)

Cage guided valves, single-seat valves, cage control valves

❗ Butterfly valves, ball valves and other rotary valves require IP8100, IP8000 is not applicable.

📌 Application Characteristics

제어 유형: Continuous modulating (not on/off valve). 4~~20mA corresponds to 0~~100% valve travel.

Air source: 깨끗한, 마른, oil-free compressed air. Air filter regulator (AFR) must be installed upstream.

장점: 간단한 구조, 쉬운 유지 보수, good anti-EMI performance. Suitable for sites without bus communication requirements and limited budget.

제한사항: Mechanical feedback, no auto-calibration. Manual zero and span adjustment required; no fault diagnosis.

❌ 권장되지 않는 시나리오

  1. Severe oscillation, strong corrosive gas (extra housing protection required).
  2. 원격진단, 하트 통신, auto-tuning required → upgrade to IP8001.
  3. Rotary butterfly / ball valves → select IP8100.
  4. 심한 먼지, unpurified instrument air (high risk of nozzle clogging).

SMC IP8000 — 선택 체크리스트

IP8000 선형 기계식 전기 공압식 포지셔너에 적용 가능; 회전식 애플리케이션에는 IP8100을 사용하세요.; IP8001 스마트 모델에는 별도의 선택 규칙이 있습니다..

  1. 액추에이터 & 밸브 기본 정보
항목 확인선택 요구 사항 & 비고
액추에이터 유형선형 스트로크 다이어프램 공압 액츄에이터 (단동식 / 이중 작용). 로터리 버터플라이/볼 밸브용 아님.
밸브 스템 스트로크10~85mm; 실제 스트로크 확인. 범위 외 여행 무효; 스트로크가 너무 작으면 피드백 레버 정확도가 저하됩니다..
액추에이터 동작□ 단동 (봄 귀환), 포지셔너 내부 피드백 스프링 교체
□ 복동형 (봄이 없어, 양방향 공기 공급), 내부 피드백 스프링 교체
밸브 종류1인용 / 새장 / 케이지 유도식 변조 제어 밸브; 변조 서비스, not on/off valve
줄기 직경 & 마운트 브래킷DIN/IEC 60534-6-1 / NAMUR 표준. 피드백 연결 및 요크 액세서리 확인. 과도한 스템 흔들림으로 인해 진동 발생.
  1. 프로세스 & 작동 조건
항목 확인선택 요구 사항 & 비고
프로세스 미디어물, 증기, 공기, 일반 화학유체. Evaluate housing protection for highly corrosive media.
Explosion-proof Requirement□ Standard non-explosion (safe area)
□ ExdⅡBT5 explosion-proof (위험 지역, temperature limit: -20~60℃; standard model -20~80℃)
주변 온도기준: -20℃ ~ +80℃; 방폭형: -20℃ ~ +60℃. Heat insulation required for over-temperature sites.
인클로저 보호표준 IP65; IP66 optional (suffix X310). IP65+ recommended for outdoor, 습하고 먼지가 많은 환경.
진동No resonance from 5~200Hz. Reinforce linkage under heavy vibration to avoid continuous hunting.
Control Requirement4~20mA analog continuous modulation; No HART, no auto-tuning. Manual zero/span calibration needed.
  1. Air Supply System Check (Highest Failure Source)
항목 확인선택 요구 사항 & 비고
Supply Pressure Range0.14~0.7 MPa. Stable pressure; pressure fluctuation easily triggers valve oscillation.
Air Quality마른, 깨끗한, oil-free compressed air. Pre-install air filter regulator (AFR) to remove water, oil and dust. Dust environment easily clogs nozzle.
Air Port ThreadG1/4 / Rc1/4 / 1/4NPT; gauge port Rc1/8. Confirm thread before ordering.
  1. Electrical Check
항목 확인선택 요구 사항 & 비고
입력 신호DC 4~20mA; 입력 저항 23515. Match signal source load capacity.
Electrical EntryG1/2 / M20*1.5 / 1/2NPT. Explosion-proof model requires explosion-proof cable gland.
배선2-wire 4-20mA. Polarity matters; reversed polarity causes no operation. Shielded cable recommended for long distance, single-end grounding.
  1. Auxiliary Accessories Selection

□ Pressure gauge: 0=0.3MPa, 3=1.0MPa (select based on output pressure range)

□ Feedback lever, yoke linkage (matched to actuator stroke)

□ Air filter regulator, air tubing

□ Mounting bracket and fasteners

□ Explosion-proof cable gland (mandatory for explosion-proof models)

  1. Exclusion Criteria (Do NOT select IP8000 if any applies)
  2. Rotary valve (butterfly / V-ball valve) → use IP8100
  3. 하트 통신, 원격진단, auto-tuning required → use IP8001
  4. Unpurified air source with heavy dust, oil and condensate
  5. Valve stroke >85mm or <10mm
  6. 심한 부식, heavy shock vibration without protective measures
  7. Selection Example (Model Code Reference)

IP8000-3 (1.0MPa gauge) + 폭발 방지 + G1/4 air port + M20 electrical entry

IP8000-301: 1.0MPa gauge, standard housing, standard lever assembly

  1. 설치 전 검사
  2. Air piping fully purged to remove welding slag and debris.
  3. Feedback lever near 90° at 50% 신호 (12엄마).
  4. No leakage on actuator; packing friction shall not be excessive.
  5. Shielded cable grounding; separate routing from power cables to avoid VFD interference.

SMC IP8000 Electro-Pneumatic Valve Positioner — Maintenance Manual

Applicable to IP8000 mechanical linear E/P positioner; Pre-work safety: Disconnect 4~20mA signal, shut off air supply and vent pressure. Never open housing under pressure.

  1. 유지보수 간격 (일일 / 계간지 / 연간)

1) Daily Routine Inspection (per shift / daily visual check)

  1. Check housing for air leakage, 응축, corrosion and loose fittings.
  2. Observe two pressure gauges for stable readings; watch for fluctuation/hunting.
  3. 밸브 스템의 움직임을 확인하세요.: 원활한 여행, 달라붙거나 이상한 소리가 나지 않음.
  4. 적시에 공기 필터 조절기에서 응축수를 배출하십시오..
  5. 장착 브래킷 확인, 느슨함을 위한 피드백 연결 및 볼트.

경고 표시: 게이지 바늘이 지속적으로 점프함, 밸브 헌팅 → 피드백 메커니즘 또는 노즐 막힘을 먼저 검사하십시오..

2) 분기별 유지보수 (모든 3 개월)

  1. 공기 필터 조절기의 필터 요소를 검사합니다.; 오염된 경우 교체.
  2. 피드백 레버를 확인하세요, 요크 및 핀 샤프트: 최소한의 그리스를 바르십시오 (과도하게 윤활하지 마십시오! 과도한 그리스는 먼지를 잡아주고 노즐을 막습니다.).
  3. 하드웨어를 조이세요: 포지셔너 장착 볼트, 튜브 피팅 및 터미널 블록.
  4. 기능 테스트: 입력 4mA, 12엄마, 20엄마, 제로 및 스팬 편차 기록.
  5. 케이블 및 케이블 글랜드 검사; 밀봉이 손상되지 않도록 보장, 물 유입 없음.

3) 연간 점검 (일년에 한 번; 모든 6 혹독한 조건에서 몇 달 동안)

  1. 유닛 분해, 깨끗한 내부 하우징, 노즐에 집중하다, 플래퍼 및 파일럿 밸브 제한 장치 (가장 높은 실패 지점).
  2. O-링 분해 및 검사; 노후된 경우 전체 밀봉 키트를 교체하십시오., 딱딱해지거나 갈라짐.
  3. 과열 변색이 있는지 토크 모터 코일을 검사하십시오.; 노즐-플래퍼 간격 확인.
  4. 제로 및 스팬 재보정, 교정 데이터 기록.
  5. 공기 튜브 검사; 노후된 호스 교체.
  6. 방폭 버전에 대한 추가 확인: 폭발 접합 표면이 손상되지 않음, 개스킷이 손상되지 않은 상태, 내염방폭 규격 준수.

가혹한 서비스 (먼지, 습기, 폐수, 종이): 유지보수 간격을 절반으로 단축.

  1. 주요 구성 요소 유지 관리

✅ 노즐 & 파리채 (가장 일반적인 오류 소스)

  1. 청소: 0.2mm 가는 나일론/구리선을 사용하여 노즐 구멍을 부드럽게 청소합니다.. 단단한 강철 와이어로 노즐 표면을 긁지 마십시오..
  2. 저압의 건조한 압축 공기로 먼지를 불어냅니다. (≤0.2MPa). 포지셔너 내부를 액체로 세척하지 마십시오..
  3. 스크래치와 오일 오염이 없는 플래퍼 표면. 긁힘으로 인해 지속적인 사냥이 발생함; replace nozzle-flapper assembly.
  4. 요구 사항: Instrument air must be dry and oil-free. Oil film on nozzle-flapper causes drift and oscillation.

✅ Feedback Lever Assembly

  1. Apply only tiny amount of lubricant to pin shafts and pivots; no heavy grease.
  2. Check linkage for deformation; no sticking during stem movement.
  3. ~에 50% 신호 (12엄마), lever should stay near 90°. Readjust mounting if angle deviates largely.

✅ Seals (O-rings)

O-rings age and harden under large temperature fluctuation and continuous operation.

Apply thin layer of TORAY SH45 silicone grease when replacing O-rings, avoid over-application.

Prevent scratches on O-ring grooves during assembly.

✅ Electrical Section

  1. Inspect 4~20mA 2-wire terminals for oxidation and looseness; 차폐 케이블의 단일 종단 접지.
  2. Explosion-proof model: power cut before cover removal. 방폭 결합 표면을 손상시키지 마십시오.; 씰 개스킷과 케이블 글랜드는 씰링된 상태로 유지되어야 합니다..
  3. VFD 간섭을 방지하려면 신호 케이블을 전원 케이블에서 분리하세요..
  4. 장기 정지 보존 (서비스 중단 >1 월)
  5. 공기 공급을 차단하고 압력을 배출합니다.; 4-20mA 신호 분리.
  6. 밸브를 중간 위치로 설정 (50% 열기) 장기적인 단면 스프링 응력을 줄이기 위해.
  7. 공기 필터에서 응축수 배출.
  8. 노즐 플래퍼에 먼지가 쌓이는 것을 방지하기 위한 먼지 보호용 커버 하우징.
  9. 공기 배관 퍼지 및 영점 재보정 & 재가동 전 기간.
  10. 금지된 작업 (중요한 경고)

❌ 압력 또는 전원 공급 상태에서 포지셔너 하우징 열기

❌ 고압 압축 공기를 사용한 블래스트 노즐-플래퍼 어셈블리

❌ 그리스를 다량 도포합니다. (먼지와 막힘 노즐을 잡아줍니다.)

❌ 내부 부품을 액체로 씻어냅니다. (하우징 외부는 젖은 천으로만 닦으십시오.)

❌ Force feedback lever; may deform torque motor and cam

❌ Use instrument air with oil, water and heavy contaminants

  1. Post-Maintenance Verification Procedure

Follow sequence after maintenance:

  1. Apply air supply, verify all air joints leak-free.
  2. Connect 4~20mA signal generator.
  3. 4mA → zero calibration; 20mA → span calibration; repeat 2~3 cycles.
  4. Test linearity at midpoint 12mA; confirm no oscillation or lag.
  5. Record calibration data and file maintenance log.
  6. Quick Fault Reference During Maintenance
  7. Valve hunting / small cycling: Dirty nozzle/flapper; wrong feedback lever angle; unstable supply air.
  8. 제로 드리프트: Condensate in air; minor O-ring leakage; slight nozzle clogging.
  9. 출력 압력이 부족함: Stuck pilot valve; 막힌 공기 필터.
  10. Large hysteresis: Pivot sticking and high friction; excessive packing friction of actuator.

이전:

다음:

답장을 남겨주세요

메시지를 남겨주세요