Полное имя: GX-series EtherCAT IO-Link Master Unit (IP67 Field Type)
Основное позиционирование: Шина EtherCAT, 8-channel IO-Link master, M12 A-coding female connector. Пыленепроницаемый и водонепроницаемый, can be mounted directly on equipment frames or production lines without installation inside control cabinets.
✅ Ключевые характеристики
Number of ports: 8 IO-Link ports (M12 A-coding female)
Bus interface: EtherCAT (IN/OUT M12, supports daisy-chain connection)
Версия IO-Link: V1.1.2
Скорость передачи данных: COM1 (4.8k) / COM2 (38.4k) / COM3 (230.4k) автоадаптивный
Power supply per port: 24 В постоянного тока, Макс. 200mA per port, with independent short-circuit protection
SIO compatible mode: Switchable to PNP DI / PNP DO
ОТ: ON ≥15V, OFF ≤5V; multi-stage filter time optional (заводская настройка по умолчанию: 1РС)
ДЕЛАТЬ: Двухтактный выход, 0.3на канал
Power supply range: 20,4 ~ 26,4 В постоянного тока (24V ±10%/-15%)
Класс защиты: IP67 (suitable for dusty and humid field environments)
Программное обеспечение для настройки: Сисмак Студия, CX-ConfiguratorFDT
Совместимый ПЛК: NX/NJ/NY series EtherCAT controllers
✅ Main Features
- IP67 field mounting, saves junction boxes, adopts M12 Smartclick quick connectors
- 8 independent IO-Link master ports. Each port can connect IO-Link sensors, valve islands, аналоговые модули, RFID and other smart slaves
- Flexible port mode switching: IO-Link smart mode / SIO digital DI / SIO digital DO
- EtherCAT daisy-chain, simple networking. Diagnostic information (sensor temperature, signal quality, event alarms) can be uploaded to PLC
- Supports automatic upload, download and backup of IO-Link device parameters. No manual setting required after sensor replacement
✅ Similar Series & Альтернативная ссылка
GX-ILM04C: 4-портовая версия (same architecture IP67 EtherCAT IO-Link master)
NX-ILM08C: NX backplane type (cabinet-mounted, non-IP67), не путай
✅ Типичные сценарии применения
Сборочные линии, упаковочные машины, станки, material handling lines, for mass connection of IO-Link photoelectric sensors, датчики приближения, датчики давления, flow sensors, proportional valves and IO-Link hubs.
✅ Notes
EtherCAT cables shall be CAT5e or higher grade shielded STP cable;
SIO DO is PNP push-pull output, cannot directly drive heavy loads;
All ports share 24V power supply, with independent short-circuit protection for each port.
GX‑ILM08C’s core advantages: IP67 field-side installation, EtherCAT daisy-chain, 8-channel IO‑Link, ports compatible with ordinary DI/DO. It is designed for outside control cabinets, dusty and humid production lines, and differentiated from NX‑ILM08C (IP20 for cabinet installation).
- Типичные отраслевые применения
- Automotive component assembly lines, оснастка приспособления, роботизированные рабочие станции
Connected to IO-Link proximity sensors, фотоэлектрические датчики, cylinder magnetic switches, датчики давления, proportional valves, fixture in-place sensors.
Преимущества: Modules can be mounted beside tooling without routing cables back to cabinet junction boxes; sensor temperature, signal margin and offset data can be read for predictive maintenance. Parameters can be downloaded automatically during fixture changeover to shorten product change time.
- Упаковочное оборудование (flow wrappers, упаковщики коробок, паллетайзеры)
For photoelectric detection, material level, давление, web guiding sensors and IO-Link valve islands. IP67 rating fits oily and humid conditions. Ordinary PNP sensors can be used in SIO mode, friendly for retrofitting projects mixing old and new sensors.
- Material handling lines, сортировочные линии, автоматизированные склады, AGV stations
Обнаружение положения, code-reading trigger and photoelectric sensors for belt conveyors, roller lines and transfer units. Long-distance segmented EtherCAT daisy-chain wiring. Обрыв провода, short circuit and sensor disconnection alarms are sent to PLC for fast fault location and reduced downtime.
- Станки, stamping and injection molding equipment
Peripheral detection of machine tools, световые завесы безопасности, mold confirmation, mold pressure, cooling circuit flow and temperature. Resists cutting fluid and dust. Sensor degradation data can be collected for early warning to avoid defective batches.
- Еда & pharmaceutical production lines (wash-down environments)
IP67 protection and M12 quick connectors for wash applications. Connected to sanitary IO-Link flow, temperature and level sensors. Supports sensor ID verification to prevent wrong installation.
- Литиевая батарея & photovoltaic equipment (liquid injection, lamination, сортировка)
Centralized access of large numbers of small-point smart sensors. Sensor parameters can be backed up and restored with one click; no on-site commissioning required when replacing sensors in batches. Status data can be uploaded to SCADA for OEE analysis.
- Functional Use Cases
Датчик condition visualization & профилактическое обслуживание: Monitor photoelectric received light intensity, sensor temperature, vibration and pressure, set threshold alarms before total failure.
Production line retrofitting: Expand I/O points locally on site without adding new control cabinets. Legacy sensors use SIO DI/DO while new smart sensors run IO-Link.
Flexible multi-product production lines: Automatic parameter download for product changeover, automatic sensor identification and anti-mismatch function.
Distributed I/O architecture: Multiple scattered acquisition points on one line connected via EtherCAT chain, reducing heavy multi-core cables.
III. Неподходящие сценарии
Cabinet internal installation with compact backplane requirement: choose NX‑ILM08C
High corrosion or continuous immersion conditions (only IP67, not for long-term submersion)
High-current loads per channel (Макс. 0.3A for DO ports)
- Matching Configuration
Контроллер: NX/NJ/NY series EtherCAT PLC; Программное обеспечение: Сисмак Студия; сеть: Multiple GX modules daisy-chained with STP shielded EtherCAT cables.
ОМРОН GX-series IO-Link Master Units
✅ GX series only has one official IO-Link master model: GX-ILM08C. GX-ILM04C does not exist; the 4-port field IO-Link master does not belong to the GX series.
| Модель | Порты | Защита | Автобус | Интерфейс | Описание |
| GX-ILM08C | 8 IO-Link | IP67 | EtherCAT | M12 A-coding female (IO-Link); M12 D-coding (EtherCAT IN/OUT) | Field distributed I/O, M12 quick connect, port switchable SIO DI/DO, compatible with NX/NJ/NY EtherCAT controllers |
Confusable IO-Link Masters from Related Families (Not GX series)
| Модель | Ряд | Порты | Защита | Автобус | Строительство |
| NX-ILM400 | НХ | 4 | IP20 | EtherCAT | Cabinet backplane mounting, винтовой терминал, for indoor cabinet use |
| NXR-ILM08C-ECT | NXR | 8 | IP67 | EtherCAT | Rugged remote terminal, similar form factor to GX |
| NXR-ILM08C-EIT | NXR | 8 | IP67 | ЭтерНет/IP | EtherNet/IP version, not EtherCAT |
Additional GX-series EtherCAT Remote I/O Modules (Not IO-Link Masters)
GX is Omron’s large IP67 EtherCAT remote I/O family. Besides IO-Link master, it includes digital and analog modules:
GX-ID16□2 / OD16□2 / MD16□2: 3-tier terminal digital I/O
GX-□D16□1 / OC1601: 2-tier terminal digital I/O
GX-□D16□8 / □D32□8: e-CON connector digital I/O
GX-AD0471 / DA0271: Аналоговый вход / аналоговый выход
GX-EC0211 / EC0241: EtherCAT junction / branch units
GX-JC03 / JC06: Extension connectors
Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер





















NH42-63-318x560.png)



