НАПРЯЖЕННЫЙ ДГК-04F Voltage Monitoring Relay - Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер

Вичат: +86-13184948252 WhatsApp: 0086-13811255435 Электронная почта: kent@bestcontactor.com

О Контакт |

НАПРЯЖЕННЫЙ ДГК-04F Voltage Monitoring Relay - Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер

ПЛК/

НАПРЯЖЕННЫЙ ДГК-04F Voltage Monitoring Relay

Бренд: НАПРЯЖЕННЫЙ (Турция) Продукт: 3-Phase Digital Adjustable Overvoltage / Пониженное напряжение & Реле защиты последовательности фаз (Реле контроля напряжения) Model Code Explanation DGK: Series of 3-phase digital voltage control relays 04: Function code → Overvoltage + Пониженное напряжение + Phase Sequence Monitoring F: Версия с цифровым дисплеем (enhanced model) Sibling model: ДГК-04PF with extra phase loss protection Protection ...

  • Подробная информация о продукте

Бренд: НАПРЯЖЕННЫЙ (Турция)

Продукт: 3-Phase Digital Adjustable Overvoltage / Пониженное напряжение & Защита последовательности фаз Реле (Реле контроля напряжения)

  1. Пояснение кода модели

ДГК: Series of 3-phase digital voltage control relays

04: Function code → Overvoltage + Пониженное напряжение + Phase Sequence Monitoring

Ф: Версия с цифровым дисплеем (enhanced model)

Sibling model: ДГК-04PF with extra phase loss protection

  1. Функции защиты
  2. 3-защита от перенапряжения фаз (ты>)
  3. 3-защита от понижения напряжения фазы (ты<)
  4. Последовательность фаз / reverse phase protection (phase sequence detection cannot be turned off on DGK-04Ф)
  5. Real-time digital display of 3-phase line voltages + fault LED indication
  6. Технические характеристики

Источник питания & измерение: 3-phase AC380V, no neutral required, L1/L2/L3 only

Частота: 50/60Hz auto-adaptive

Undervoltage setting range: 230~360V AC

Overvoltage setting range: 400~460V AC

Время задержки неисправности: 0.1~10s adjustable

Выходной контакт: 1НО+1НЗ (SPDT), 5А / 250V AC resistive load

Монтаж: Стандартный монтаж на DIN-рейку

Рабочая температура: -10℃ ~ +55 ℃

Measuring accuracy: ±1 В

  1. Определение терминала

Л1, Л2, Л3: 3-phase voltage input

1, 2, 3: Relay changeover contacts

Терминал 1: Северная Каролина (Нормально закрытый)

Терминал 2: КОМ (Общий)

Терминал 3: НЕТ (Нормально открытый)

Стандартная проводка (Мотор / Air Compressor / Водяной насос)

Contactor coil circuit: Wire in series with 2-3 (НЕТ)

Alarm lamp / Buzzer: Connect to 1-2 (Северная Каролина)

Safety note: L1/L2/L3 must be from the same 3-phase power source; do not mix phases from different circuits.

  1. Электропроводка & Commissioning Manual

Panel Buttons & Индикаторы

ты: Overvoltage setting key

ты< : Undervoltage setting key

т : Time delay setting key

Цифровой дисплей: Cyclically shows L1-L2 / Л2-Л3 / L3-L1 line voltages

ВНЕ: Relay output indicator (ВКЛ в нормальном состоянии)

ты: Overvoltage fault LED

ты< : Undervoltage fault LED

PHASE: Phase sequence error LED

Power-on logic: The unit shows parameter settings for 2 seconds first, then automatically cycles through 3-phase voltage readings.

Pre-power Check (Обязательный)

  1. Perform all wiring with power disconnected; confirm no short circuit on L1/L2/L3.
  2. Contact load limit: Max 5A/250VAC; only interlock the control circuit, do not switch main power of large contactors directly.
  3. Keep away from inverters and large contactors to avoid strong electromagnetic interference.

Step-by-step Commissioning

Шаг 1: Включение питания

Switch on 3-phase supply, digital display lights up:

OUT ON: Напряжение & phase sequence normal, relay energized, 2-3 закрыто.

PHASE ON: Phase sequence reversed → Power off and swap any two incoming phases (L1↔L2 or L2↔L3).

U/ U< НА: Voltage exceeds threshold, protection activated.

Шаг 2: Set Undervoltage U< (Рекомендуется: 340V for 380V systems)

  1. Short press the U< key to enter undervoltage setup.
  2. Press U< to increase value; press t to decrease value.
  3. Ждать 4 seconds without operation to auto-save and return to voltage monitoring screen.

Setting range: 230~360V

Шаг 3: Set Overvoltage U(Рекомендуется: 420V for 380V systems)

  1. Short press the Ukey to enter overvoltage setup.
  2. Press Uto increase value; press t to decrease value.
  3. Auto-save after 4 seconds idle.

Setting range: 400~460V

Шаг 4: Set Fault Time Delay t (Recommended 1~3s to avoid false tripping from momentary voltage dips)

  1. Short press the t key to enter delay setup.
  2. U= increase time; ты< = reduce time.
  3. Settings take effect after auto-save.

Диапазон: 0.1~10 с; same delay applies for fault trip AND automatic reset after voltage recovers.

Шаг 5: Phase Sequence Function Note

ДГК-04Ф: Обнаружение последовательности фаз невозможно отключить.. Reverse phase will trigger protection, PHASE LED lights up, OUT turns off, and contact 2-3 открывается.

If phase sequence monitoring is not required (fans without rotation direction requirement), you need to select another model. Only DGK-04PF adds phase loss protection.

Шаг 6: Functional Test

  1. Нормальное состояние: OUT stays ON, 2-3 закрыто, contactor can energize.
  2. Simulate overvoltage: Raise supply voltage or lower the Uthreshold; ULED lights up, OUT cuts off, 2-3 открывается.
  3. Simulate undervoltage: Lower supply voltage or raise the U< порог; ты< LED lights up, реле обесточивает.
  4. Swap two phases: PHASE fault triggers, relay drops out.

Гистерезис: Relay only restores after voltage returns within the set window (+5V tolerance) plus the programmed time delay.

Recommended Parameters (AC380V 3-phase Equipment)

Undervoltage U<: 340В

Overvoltage U>: 420В

Time delay t: 2с

Список устранения неполадок

  1. PHASE LED always ON after power-up: Phase sequence reversed; swap any two incoming phases.
  2. OUT OFF with no fault indication: One phase is missing; measure line voltages on L1/L2/L3.
  3. Частые ложные срабатывания: Increase time delay t; check for grid voltage flicker or loose terminal connections.
  4. Flashing reading on one phase: Abnormal voltage on that phase.
  5. Voltage reading normal but relay will not energize: Check continuity of terminals 2-3 and the contactor control circuit.

Strict Prohibitions

❌ Never connect L1/L2/L3 to the output terminals of an inverter (distorted sine wave will cause false fault alarms).

❌ Do not feed single-phase 220V power into L1/L2/L3.

❌ Do not use the relay contacts to drive high-power loads directly; only use them for control circuit interlock.

Временная задержка (т) Setting for TENSE DGK-04Ф

Delay range: 0.1~10 seconds. This single setting covers both fault confirmation delay AND voltage recovery reset delay. The relay will only re-energize after the voltage returns to normal and the set time elapses.

Этапы работы

  1. While the display is cycling through line voltages, short press the t key to enter delay setup; the digital tube shows the current time value.
  2. Press U= increase time value
  3. Press U< = decrease time value
  4. Stop pressing any key; wait approx. 4 seconds for auto-save, then the unit returns to voltage monitoring mode automatically.

✅ Factory recommended setting: 1~2s to filter short grid transients and prevent false tripping.

Воздушные компрессоры & водяные насосы: 2s preferred

Fast cut-off protection requirement: set to 0.5s

Key Logic

When overvoltage / пониженное напряжение / reverse phase occurs: Реле начинает отсчет времени; contacts only open after the delay expires.

When the fault clears and voltage recovers (with +5V hysteresis): The relay waits the same t seconds before closing contacts again.

Phase sequence faults also follow this same time delay setting.

Общие проблемы

New setting not saved: Do not press any confirm key; just wait for automatic return. Avoid long key presses.

Unwanted frequent tripping: Increase the t value.

Slow recovery after fault: Reduce the t value appropriately.

Full Model List of TENSE (Турция) DGK Digital Voltage Monitoring Relays

DGK series: Digital readout, adjustable over/undervoltage, Монтаж на DIN-рейку, no neutral required (L1/L2/L3 line voltage detection).

Определение суффикса: F = digital display; P = phase loss protection added

МодельФазаОсновные функцииПримечания
ДГК-01ОднофазныйAdjustable overvoltage + пониженное напряжение, цифровой дисплейAC220V single-phase monitoring
ДГК-033-фазаРегулируемое повышенное/пониженное напряжение, no phase sequence check, цифровой дисплейFor loads with no rotation direction requirement
ДГК-043-фазаРегулируемое повышенное/пониженное напряжение, no phase sequence, analog knob (нет дисплея)Analog version without digital readout
ДГК-04Ф3-фазаПеренапряжение + Пониженное напряжение + Последовательность фаз, цифровой дисплейВаша текущая модель; no phase loss protection, phase sequence check cannot be disabled
ДГК-04ПФ3-фазаПеренапряжение + Пониженное напряжение + Последовательность фаз + Потеря фазы, цифровой дисплейUpgraded model of DGK-04Ф, widely used on air compressors & чиллеры

Analog Knob Series (Серия ГК, No Digital Display)

МодельФункция
ГК-033-phase over/undervoltage adjustable, no phase sequence
ГК-043-phase over/undervoltage adjustable, no phase sequence
ГК-04Ф3-повышенное/пониженное напряжение фазы + последовательность фаз

Последовательность фаз / Потеря фазы / Unbalance Protection Series (FK / FKV Series, without continuous voltage adjustment window)

These models focus on phase loss, 3-phase unbalance and phase sequence; some support PTC motor temperature protection, not the DGK over/undervoltage main series.

FK-04: Потеря фазы + последовательность фаз, зафиксированный 30% unbalance threshold

FK-05 / FK-05Ф: Потеря фазы + последовательность фаз, unbalance adjustable 5~25% (F = digital display)

FK-14 / FK-14P: Последовательность фаз + потеря фазы; P model with PTC motor thermal protection

ФКМ-05 / ФКМ-05Ф: Adjustable unbalance, последовательность фаз, потеря фазы

FKT-06 / FKT-06ПФ: 3-фазовый дисбаланс + потеря фазы + последовательность фаз; PF with PTC input

FKV-03 / FKV-03Ф / FKV-03ДФ / FKV-03HF: Потеря фазы, последовательность фаз, разбалансировать; some versions require neutral N

FKV-14 / FKV-14P: Economy phase sequence & реле потери фазы; P with PTC protection

Suffix Quick Reference

Ф: Digital display type

П: Phase loss protection function

Т: Built-in PTC motor temperature protection

DF/HF: Adjustable unbalance ratio

Н: Requires neutral wire (3П+Н)

Руководство по быстрому выбору (Most Popular Engineering Models)

  1. Only over/undervoltage monitoring, no rotation check: ДГК-03
  2. Повышенное/пониженное напряжение + anti-reverse phase (motor rotation control): ДГК-04Ф
  3. Повышенное/пониженное напряжение + anti-reverse phase + защита от потери фазы: ДГК-04ПФ (first choice for air compressors & охладители воды)
  4. Only phase loss & unbalance monitoring without voltage threshold adjustment: FK-05Ф / FKV-14

Common Specifications for All DGK 3-phase Models

Выход: 1NO+1NC SPDT contact, 5А/250 В переменного тока

Time delay: 0.1~10s adjustable (shared trip & reset delay)

Диапазон напряжения: Undervoltage 230~360V; Overvoltage 400~460V (for 380V line voltage systems)

Власть & measurement input: L1/L2/L3 only, no neutral wire needed

Предыдущий:

Оставить ответ

Оставить сообщение