Ряд: Modicon X80 32-point Sourcing Transistor Digital Модуль вывода, Conformal Coated (Severe Environment Version)
Corresponding standard non-coated version: BMXDDO3202K
✅ Объяснение кода модели
BMX: X80 I/O Series
ДДО: Digital Discrete Output
32: 32 каналы
02: 24VDC transistor output
К: Sourcing type (Позитивный / Current Source)
С: Conformal coating (anti-corrosion, влагостойкий, dust-proof for severe environments)
📌 Основные электрические характеристики
Тип выхода: Sourcing transistor (ПНП, положительная логика)
Внешнее питание: 24В постоянного тока, range 19~30VDC
Номинальный ток на канал: 0.125А (nominal 0.1A)
Maximum total module current: 3.2А
Ток утечки в выключенном состоянии: ≤0,1 мА
On-state voltage drop: <1.5V
Время отклика выхода: 1.2РС
Channel parallel connection: Допустимый, Макс. 3 channels in parallel
Потребляемая мощность: 3.6Вт
Backplane 3.3V current draw: Приблизительно. 125мА
Изоляция: 500В постоянного тока, insulation resistance >10MΩ
Защита: Защита от обратной полярности, перенапряжение, current limiting; 2A external fast fuse recommended for each group against short circuit
Разъем: 1 × 40-pin FCN flat cable connector (no built-in terminal block, requires matched FCN40 cable)
🧱 Механический & Относящийся к окружающей среде
Размеры: W32 mm × H100 mm × D86 mm
Вес нетто: 0.11 кг
Класс защиты: IP20 (module only, cabinet-mounted)
Рабочая температура: 0 ~ +60℃ (coated version, suitable for high-humidity, пыльный, salt-spray environments)
среднее время безотказной работы: Приблизительно. 290,000 часы
Сертификаты: CE, UL, CSA, UKCA, ЕАС, РКМ, marine classification certification
🤖 PLC Compatibility
Модикон М340 (local rack / X80 remote I/O)
Модикон М580 (local rack / X80 remote I/O, ePAC)
⚠️ Selection Comparison
| Модель | Покрытие | Тип выхода |
| BMXDDO3202K | Стандартный, no coating | 32 × 24VDC sourcing transistor |
| BMXDDO3202KC | Conformal coating (С) | 32 × 24VDC sourcing transistor |
🛠️ Typical Application & Примечания
- Suitable for driving DC24V indicators, маленькие реле, соленоидные катушки (observe single-channel current limit)
- Wiring only via 40-core FCN flat cable; incompatible with regular terminal bases directly
- Transistor output cannot drive AC loads, нет механических контактов, not suitable for high-frequency large inductive loads. Freewheeling diode in reverse parallel is mandatory for inductive loads
- Coated version for water treatment, добыча полезных ископаемых, морской, outdoor cabinets and other high-humidity corrosive scenarios
- Matched FCN40 Factory Cables
Cables are fully interchangeable between BMXDDO3202KC and BMXDDO3202K, 40-pin Fujitsu FCN connector
1) Flying-lead type (strip wires directly to cabinet terminals)
BMXFCW303: 3м, 40-основной, pre-stripped colour-coded wires split into 2 группы 20
BMXFCW503: 5м
BMXFCW1003: 10м
2) With ABE7 Telefast terminal base (HE10 dual connector, most common for engineering)
One BMXDDO3202KC requires 2 pcs of ABE7 16-point bases
BMXFCC053: 0.5м
BMXFCC103: 1м
BMXFCC203: 2м
BMXFCC303: 3м
BMXFCC503: 5м
BMXFCC1003: 10м
Common ABE7 bases for reference:
ABE7H16C10, ABE7R16S111, ABE7R16T111 (16-point sourcing DC output terminal blocks)
Примечание: Third-party compatible FCN40 cables (MISUMI, Weidmüller etc.) are available on market. Confirm specs before purchase: Fujitsu FCN-40P male, 0.14мм², 24В Вашингтоне
- I/O Address Mapping (M340/M580, Юнити Про / EcoStruxure Control Expert)
The module occupies 2 output words (%QW), общий 32 биты
Channels Q00~Q15 → %QWx.0 ~ %QWx.15 (1st word)
Channels Q16~Q31 → %QW(x+1).0 ~ %QW(x+1).15 (2nd word)
Automatic rack allocation rule:
M340 local rack: Allocated sequentially by slot after CPU; X80 remote I/O racks follow scanner configuration order.
Channel-level diagnostics supported; короткое замыкание / overload status word can be read in the program.
- Pinout Summary (FCN40 connector, PNP sourcing)
1~20: Q00~Q15 outputs + grouped supply SPS+, SPS-
21~40: Q16~Q31 outputs + grouped supply SPS+, SPS-
Module internally divided into 2 independent supply banks of 16 каналы каждый. Independent 2A fast fuse per bank recommended. Для индуктивных нагрузок (соленоиды, реле), connect reverse freewheeling diode (1N4007) across coil terminals.
- Контрольный список устранения неполадок
- Светодиод «РАБОТА» выключен
Poor backplane bus contact: Re-seat module, check rack latches; test in alternative slot
Недостаточная мощность объединительной платы; rack power supply undersized
Hardware module damage (coated version less prone to corrosion failure; check backplane first)
- RUN LED ON, channel LEDs do not follow program output
Confirm PNP sourcing wiring: Negative terminal of load to 24V-, output provides +24V
Loss of external SPS supply, перегоревший предохранитель (failure of half channels usually means fuse blown for that bank)
Wrong program address, forced value or interlock blocking output
- Channel LED ON but load not actuated
On-state voltage drop>1.5V: Short circuit at load, burnt channel; measure channel voltage to GND
Ток утечки: Dim glow at OFF state is inherent transistor leakage (≤0,1 мА, common for small indicators)
- Repeated channel fault / burnt channels
Missing freewheeling diode for inductive loads, breakdown by back EMF
Single-channel current over 0.125A; total module current exceeds 3.2A limit
Reverse polarity of external 24V supply, high voltage intrusion
- Special notes for humid/corrosive environments (KC coated version)
Conformal coating protects PCB only; not resistant to condensation or liquid ingress. Cabinet temperature control and dehumidification required
FCN connector pins vulnerable to salt spray oxidation; apply contact protection spray on connectors
- Варианты замены (Same-platform / Domestic PLC replacement)
✅ Direct Шнайдер same-platform replacement (no program change, no base modification)
Standard non-coated version: BMXDDO3202K (only without conformal coating, идентичные электрические параметры)
Предупреждение: Do not replace KC directly with K for humid / salt-spray / mining environments, service life will be drastically reduced
✅ Domestic alternatives (complete PLC replacement, incompatible with X80 backplane, требуется миграция программы)
Selection criteria: 32-point 24VDC PNP sourcing transistor output, 0.1на канал, with channel diagnostics
Common options:
- Инновации: AM600 series AM600-32DO (ПНП, check revision)
- Синдже: XD/XG series 32-point DO module
- HCFA: HC-A0/HC-Q series 32-point transistor output
- ХоллиСис: LX series 32DO sourcing module
Важное напоминание: Domestic modules have no FCN40 port, terminal-block design only. If existing FCN wiring harness is retained, domestic modules cannot be used for direct swap; only Schneider X80 applies.
- Additional Maintenance Notes
Parallel channels allowed: Макс. 3 channels in parallel for higher drive current
Время ответа: 1.2РС, not suitable for high-speed pulse / PWM output
Хранилище: Coated modules resist corrosion, but avoid high temp & humidity for long-term storage; sealed moisture-proof storage recommended
BMXDDO3202KC Full Technical Datasheet (Schneider Official)
Ряд: Modicon X80; Тип: 32-point 24VDC sourcing (ПНП) transistor digital output module; C = Conformal Coated Severe Environment Version
- Основная информация
Модель: BMXDDO3202KC
Совместимые процессоры: Модикон М340 / M580 (local rack, X80 remote I/O station)
Количество каналов: 32 ДЕЛАТЬ, split into 2 banks × 16 independent supply domains
Тип выхода: Solid-state transistor, Positive Sourcing (ПНП)
Стандартный: ЕН/МЭК 61131-2
Интерфейс: 40-pin Fujitsu FCN flat cable interface, no built-in terminal block
- Electrical Output Ratings
External supply SPS: 24 В постоянного тока, 19В ~ 30 В постоянного тока
Rated continuous current per channel: 0.1А; текущий предел: 0.125А
Max total module output current: 3.2А
Ток утечки в выключенном состоянии: ≤0,1 мА
On-state voltage drop: <1.5V
Время отклика выхода: 1.2 РС
Parallel channels: Permitted, Макс. 3 channels in parallel
Защита от перегрузки: Built-in current limiting + электронное путешествие, overload range 0.125~0.185A
Защита от короткого замыкания: On-board current limiting, external 2A fast fuse required for each 16-channel bank
Защита от перенапряжения: Transil transient suppressor diode; reverse protection: reverse diode
Изоляция: 500В постоянного тока, insulation resistance>10MΩ
Fault detection threshold: >18V DC = normal; <14V DC = upstream supply fault alarm
Типичное энергопотребление: 3.6Вт
Backplane 3.3V bus consumption: Typical 125mA
- Диагностика & Индикаторы
RUN green: Модуль исправен
ERR red: Ошибка модуля / неисправность автобуса
Independent green LED per channel: Channel status indication
Channel-level diagnostics supported: Короткое замыкание, перегрузка, external supply loss; fault word readable in CE/Unity Pro
- Механические характеристики
Размеры: W32 mm × H100 mm × D86 mm
Вес нетто: 0.11 кг
Класс защиты: IP20 (module only, cabinet use)
PCB treatment: Conformal coating (влага, mould and salt spray resistant)
- Экологические рейтинги
Рабочая температура: 0 ℃ ~ +60 ℃
Температура хранения: -40 ℃ ~ +85 ℃
Относительная влажность: 5% ~ 95%, неконденсирующийся (coating does not stop condensation or water ingress)
среднее время безотказной работы: 312,254 часы (reference)
Сертификаты: CE, UL, CSA, UKCA, ЕАС, РКМ, морская сертификация
- Software Address Assignment
Output occupancy: 2 %QW words (QWx, QWx+1), общий 32 биты
Q0~Q15 → QWx bit0~bit15
Q16~Q31 → QWx+1 bit0~bit15
- Comparison with Non-coated Sibling Model
BMXDDO3202K: Identical electrical specs, no conformal coating, standard indoor environment only
BMXDDO3202KC: Conformal coated, for mining, очистка воды, морской, high-humidity salt-spray cabinets
- Критические ограничения (Инженерный фокус)
- Транзисторный выход, нет контактов, cannot drive AC loads. Freewheeling diode mandatory for inductive loads
- Not designed for high-speed pulse / PWM output
- Two banks of 16 channels with isolated supplies; blown fuse only impacts that bank of 16 очки
- Only compatible with FCN40 cables (BMXFCW/BMXFCC series); direct connection to generic terminals not supported
Schneider Modicon X80 (M340/M580) Digital Output DO Module List
Code definition:
ДДО: Solid-state DC transistor output; DRA/DRC: Релейный выход; DAO: Triac AC output
K = Sourcing PNP; 12 = Sinking NPN; C = Conformal coating Severe; H = Wide temp + конформное покрытие; suffix H = severe environment grade
Interface classification: Direct terminal / FCN flat cable (requires ABE7 terminal base + FCW/FCC cable)
- DC Transistor Output (BMXDDO Series, 24В постоянного тока)
| Модель | Очки | Тип | Ток на канал | Интерфейс | Примечания |
| BMXDDO1602 | 16 | Sourcing PNP | 0.625А | 20-pin direct terminal | Standard high-current transistor |
| BMXDDO1602H | 16 | Sourcing PNP | 0.625А | 20-pin direct terminal | Wide temp coated severe -25~70℃ |
| BMXDDO1612 | 16 | Sinking NPN | 0.125А | 20-pin direct terminal | Standard sinking |
| BMXDDO1612H | 16 | Sinking NPN | 0.125А | 20-pin direct terminal | Wide temp coated sinking |
| BMXDDO3202K | 32 | Sourcing PNP | 0.125А | FCN40 flat cable | Standard non-coated base version |
| BMXDDO3202KC | 32 | Sourcing PNP | 0.125А | FCN40 flat cable | Conformal coated severe (ваша целевая модель) |
| BMXDDO6402K | 64 | Sourcing PNP | 0.125А | Dual FCN40 flat cable | Standard non-coated 64pt |
| BMXDDO6402KC | 64 | Sourcing PNP | 0.125А | Dual FCN40 flat cable | Conformal coated 64pt severe |
- Релейный выход (DRA / DRC, Совместимость с переменным/постоянным током)
Relays suited for AC220V loads; DRC = fast relay, DRA = standard relay
| BMXDRA0804T | 8 | 100~150VAC | Isolated contacts | Legacy model |
| BMXDRA0805 | 8 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Устаревший, только запасные части |
| BMXDRA0805H | 8 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Coated severe |
| BMXDRA0815 | 8 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Regular active model |
| BMXDRA0815H | 8 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Coated severe |
| BMXDRA1605 | 16 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Popular 16pt relay DO |
| BMXDRA1605H | 16 | 24В постоянного тока / 24~240 В переменного тока | Independent relay | Coated severe |
| BMXDRC0805 | 8 | 24В постоянного тока / 24~240 В переменного тока | High-speed relay | Faster operation |
| BMXDRC0805H | 8 | 24В постоянного тока / 24~240 В переменного тока | High-speed relay | Высокоскоростной + coated |
- Triac AC Output (DAO, AC loads only)
| Модель | Очки | Рейтинг | Примечания |
| BMXDAO1605 | 16 | 48~240 В переменного тока, 0.5А | Solid-state AC output, нет контактов, for AC lamps, обогреватели |
| BMXDAO1605H | 16 | 48~240 В переменного тока, 0.5А | Coated severe |
- Смешанный ввод-вывод (ДИ+ДЕЛО, common for engineering selection)
| Модель | ОТ | ДЕЛАТЬ | Тип выхода |
| BMXDDM16025 | 8ОТ | 8ДЕЛАТЬ | Релейный выход |
| BMXDDM16025H | 8ОТ | 8ДЕЛАТЬ | Реле, coated version |
| BMXDDM3202K | 16ОТ | 16ДЕЛАТЬ | 24VDC sourcing transistor, FCN cable |
✅ Quick Selection Cheat Sheet
- Direct terminal (20-приколоть): BMXDDO1602 / 1612 ряд, hardwire directly, no FCN cable needed
- FCN flat cable type: 32pt, 64pt (3202К / КС, 6402К / КС), must use BMXFCW/BMXFCC cable + ABE7 terminal block
- Difference between C and H
С: PCB conformal coating only, temp 0~60℃ (BMXDDO3202KC)
ЧАС: Conformal coating + wide temperature -25~70℃ (1602ЧАС,1612ЧАС, DRAxxH)
- Transistor outputs cannot drive AC; relay and DAO triac support AC loads
Контактор,автоматический выключатель,датчик,Кодер,ПЛК,Конвертер























NH42-63-318x560.png)



