Danfoss ICAD600A 027H9065 แอคชูเอเตอร์ไฟฟ้า Stepper - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

Danfoss ICAD600A 027H9065 แอคชูเอเตอร์ไฟฟ้า Stepper - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

บมจ/

Danfoss ICAD600A 027H9065 แอคชูเอเตอร์ไฟฟ้า Stepper

การวางตำแหน่งผลิตภัณฑ์:Stepper electric actuator (power head) for Danfoss ICM motorized valves in refrigeration systems, old A-series, obsolete ✅ Basic Information Model:ไอแคด600เอ, Order code 027H9065 Brand:ดานฟอสส์ (Refrigeration segment) Compatible valve bodies:ICM20 / ICM25 / ICM32 motorized regulating valves, also capable of driving CVE pilot valves Construction:Stepper motor driven, with valve position feedback, local keypad & แสดง, ...

  • รายละเอียดสินค้า

การวางตำแหน่งผลิตภัณฑ์:สเต็ปเปอร์ แอคชูเอเตอร์ไฟฟ้า (power head) สำหรับ ดานฟอสส์ ICM motorized วาล์ว in refrigeration systems, old A-series, ล้าสมัย

✅ ข้อมูลพื้นฐาน

แบบอย่าง:ไอแคด600เอ, Order code 027H9065

ยี่ห้อ:ดานฟอสส์ (Refrigeration segment)

Compatible valve bodies:ICM20 / ICM25 / ICM32 motorized regulating valves, also capable of driving CVE pilot valves

การก่อสร้าง:Stepper motor driven, with valve position feedback, local keypad & แสดง, manual override function

ต้นทาง:โปแลนด์

📌 ข้อมูลจำเพาะทางไฟฟ้าหลัก

แหล่งจ่ายไฟ:24ในดีซี (+10% / -15%), DC power only

Max current:1.2 ก

Control signals:

อินพุตแบบอะนาล็อก:0/4-20 มิลลิแอมป์, 0/2-10 ในดีซี

เอาท์พุทแบบอะนาล็อก:0/4-20 มิลลิแอมป์ (การตอบสนองตำแหน่งวาล์ว)

3-channel NPN digital outputs (valve position status, ความผิดพลาด, ฯลฯ)

Passive dry contact digital input

ระดับการป้องกัน:IP67

อุณหภูมิแวดล้อม:-30 ℃~ +50 ℃

ที่อยู่อาศัย:Aluminum body + PBT top cover, net weight approx. 1.2 กก

ขั้วต่อ:ขั้วต่อแบบกลม M12 (4-pin power + 8-pin signal). Pre-assembled cables available as options: 027H0426 (1.5ม), 027H0438 (3ม), 027H0427 (10ม), 027H0435 (15ม)

🧩 Control Modes

  1. Analog modulation:Continuous regulation via EKC347 level controller or PLC with 4-20mA / 0-10วีเอาท์พุต
  2. Digital position control
  3. Local panel manual open, close and calibration
  4. Compatible with ICAD-UPS power-fail hold module for safe position protection upon power loss

🔁 ตัวเลือกการทดแทน (ส่วนสำคัญ)

Factory successor:ICAD600B (หมายเลขคำสั่งซื้อ. 027H0485). สามารถเปลี่ยนได้ทางกลไก, upgraded with OLED screen, Bluetooth APP and RS485 communication. อย่างไรก็ตาม, wiring logic and parameter programming need verification and adaptation; direct blind replacement is not permitted.

Similar obsolete parts within the same series:027H9075 (ไอแคด600เอ, identical hardware to 027H9065, only version/config difference, also obsolete)

⚠️ Fault & หมายเหตุการบำรุงรักษา

ข้อผิดพลาดทั่วไป:Loss of communication, valve position non-following, แผงลอยมอเตอร์, blank display, น้ำเข้า & oxidation at M12 connectors

การสอบเทียบ:Full zero & full stroke auto-calibration must be performed after replacement or disassembly

สำคัญ:24V AC must NOT be applied directly. A dedicated isolated 24V DC power supply is required; voltage drop shall be calculated for long wiring runs

📎 Application Scope

Industrial ammonia refrigeration, CO₂ transcritical systems, large fluorinated refrigerant chiller packages, used for continuous regulation of liquid level, pressure and superheat (pump recirculation, evaporator, condenser, economizer circuits)

📋 Supporting Documentation

Manuals:AI000086409336 (General ICAD600/900 manual), AN000086415021 (สายไฟ & commissioning manual)

ไอแคด600เอ (027H9065) → ICAD600B (027H0485) Retrofit Checklist

ข้อสรุปหลัก:เข้ากันได้ทางกล, fits directly on existing ICM20/25/32 valve bodies. But M12 pin assignment, parameter menu and fault logic differ; the old cable cannot be plugged in and powered up directly.

  1. รายการวัสดุ
หมวดหมู่รายการหมายเหตุ
หน่วยหลักICAD600B, หมายเลขคำสั่งซื้อ. 027H0485Replaces 027H9065, compatible with ICM20/25/32
Optional pre-made cable027H0426 (1.5ม) / 027H0438 (3ม) / 027H0427 (10ม)B-series dedicated M12 power + M12 signal cable. Old A-series cables have different pinouts and reuse is not recommended
UPS power-fail hold027H0388 ICAD UPS moduleCompatible with A & บี; B has revised logic for UPS detection pin
วัสดุสิ้นเปลืองMolycote 55 จาระบี, โอริงFor valve stem magnetic coupling seal; lubrication mandatory after disassembly to prevent water ingress failure
เครื่องมือ2.5mm hex key, ประแจแรงบิด, มัลติมิเตอร์, เทปฉนวนInstallation torque: 3ยังไม่มีวิธี ม, tighten diagonally and evenly
  1. Mechanical Retrofit (Low Risk)

✅ Compatibility:Valve seat, magnetic coupling and mounting screw positions match completely; no modification to valve body or bracket required

⚠️ Operating Procedure

  1. Manually set valve to mid-position first (to prevent valve stem detachment after actuator removal)
  2. Loosen the 3 fixing hex screws and lift the old ICAD600A vertically
  3. Inspect magnetic coupling and O-rings on valve body for damage, ice buildup or heavy contamination; remove old grease residue
  4. Apply Molycote 55 to O-ring groove and O-ring, align magnetic coupling and lower ICAD600B vertically
  5. Tighten the 3 screws diagonally at a controlled torque of 3N·m; avoid one-sided over-tightening
  6. Verify housing sealing surface is fully seated without warping

จุดเสี่ยง:Misaligned magnetic coupling or missing grease → water ingress, magnetic coupling slip and valve position drift later

  1. Electrical Retrofit (วิกฤต! Pinout Incompatibility, Highest Risk Area)

ไอแคด600เอ:M12 power 3-pin; M12 signal 7-pin

ICAD600B:M12 power 4-pin; M12 signal 8-pin; independent 4-pin M12 RS485 port exclusive to B-series

4-pin M12 Power Connector (บี)

Pin I Black:Fail-safe 19-24V DC (UPS backup power, ไม่จำเป็น)

Pin II White:Main 24V DC+

Pin III Brown:24ในดีซี(จีเอ็นดี)

Pin IV Blue:UPS status feedback signal (Not available on A-series)

8-pin M12 Signal Connector (บี)

Pin A Black:Common terminal for fault output (เอ็นพีเอ็น)

Pin B Brown:Fully open limit output

Pin C Red:Fully closed limit output

Pin D Orange:สัญญาณ GND

Pin E Yellow:อินพุตแบบอะนาล็อก (0/4-20mA /0/2-10V)

Pin F Pink:Analog feedback output (valve position 0/4-20mA)

Pin G Grey:Digital input DI (เปิดใช้งาน / Safety close)

Pin H Violet:ที่สงวนไว้

Comparison with A: Wire color sequence for digital outputs and analog input differs. Direct plug-in of old cable will burn signal channels or trigger faults.

✅ Two implementation options:

ตัวเลือก 1: Purchase factory pre-assembled B-series cables, re-terminate wiring at cabinet terminals one-to-one (Recommended for reliable site performance)

ตัวเลือก 2: Rewire existing cable, re-crimp M12 contacts according to above definition and apply clear marking

Power requirement remains 24VDC SELV isolated power supply, max 1.2A, same as A-series; 24V AC is not supported.

  1. เจ้าภาพ / Controller Program Modification (EKC347 / บมจ)
  2. Analog control loop (4-20mA control)

Control signal range: 0/4-20มิลลิแอมป์, 0-10V definition unchanged. B internal input resistance differs; range setting on PLC/EKC side can stay, but valve position feedback reading calibration is recommended.

ก: Valve feedback 4-20mA; B also 4-20mA with improved load capacity up to 500Ω

  1. Digital position signals (Full open, Full close, ความผิดพลาด)

All three are NPN open-collector outputs with identical function definition. Common terminal pin has changed; PLC input common point wiring must be adjusted accordingly.

  1. Existing EKC347 parameters:

ซุปเปอร์ฮีต, liquid level setpoints and PID gains can be retained

Valve body model must be reselected inside B actuator (parameter i26). B will automatically calibrate stroke

  1. อาร์เอส485 (New for B): Not required if original system has no bus. If bus communication is planned later, Modbus mapping and terminating resistor need to be added.
  2. การว่าจ้าง & ขั้นตอนการสอบเทียบ (บังคับ, Skipping Causes Position Error)
  3. Double-check wiring, power on without load first, check OLED screen (B uses OLED, A uses segment LCD)
  4. Enter parameter menu, set valve body type: ICM20/25/32 (i26) → trigger automatic stroke calibration
  5. Calibration sequence: Auto full close → full open → full close, zero and full stroke recorded
  6. Manual mode test: เปิด / close via local panel, confirm smooth movement without sticking
  7. Auto mode: Apply 4mA / 20mA reference signal, verify linear tracking of valve position feedback
  8. การจำลองข้อผิดพลาด: Signal loss, การสูญเสียพลังงาน, check fault output and UPS safe position logic
  9. Save parameters and back up configuration (B supports Bluetooth APP commissioning via Danfoss BT tool)

สำคัญ:A-series fault code list cannot be used for B; B alarm system is revised and some alarm definitions are different.

  1. Risk Checklist & การหลีกเลี่ยงหลุมพราง
  2. ❌ Plug old A cable directly into B: Pin misalignment → burnt analog channels, power short circuit, A1/A2 alarms
  3. ❌ Skip calibration before commissioning: ศูนย์ดริฟท์, incomplete closure or incomplete opening
  4. ❌ Omit Molycote 55 แอปพลิเคชัน: Magnetic coupling water ingress, slip and position loss at low temperature
  5. ❌ Ignore blue UPS pin: Continuous UPS fault alarm on B if blue wire is not connected when UPS module is fitted
  6. ❌ Torque over 3N·m: Housing deformation and seal failure
  7. Acceptance Test Items

คงที่: Valve position 0%, 50%, 100%, feedback error ≤±2%

พลวัต: Step response test, no oscillation or sticking

Fault conditions: ลวดขาด, การสูญเสียพลังงาน, แผงลอย; controller receives fault signal correctly

การคุ้มครองสิ่งแวดล้อม: IP67, proper connector sealing, no condensation ingress in humid conditions

Recurring Faults after ICAD600A (027H9065) → ICAD600B (027H0485) การทดแทน, สาเหตุ & การแก้ไขปัญหา

สถานที่ตั้ง: Most issues originate from incorrect pin wiring, missing calibration, UPS logic difference, ความต้านทาน / load mismatch. Mechanical seizure of valve body is a pre-existing condition, not a new fault introduced by replacement.

  1. Power-on Faults (Alarm at power-up, ไม่มีจอแสดงผล, cyclic reboot)
  2. Blank OLED, no illumination

สาเหตุ: Wrong M12 power pin assignment, reversed 24VDC polarity, insufficient power capacity, แรงดันไฟฟ้าตกมากเกินไป, น้ำเข้า & oxidation at M12 plug

การแก้ไขปัญหา: Measure Pin II(+) & III(-) with multimeter; confirm DC24V not AC24V; measure voltage at actuator end for long cable runs

  1. Cyclic reboot & flashing screen after power-up

สาเหตุ: Blue UPS Pin IV left floating without connection; old A-type UPS module mismatched; high ripple power supply

การเยียวยา: Disable UPS detection in menu if UPS module is not used; do not leave pin floating and tolerate constant alarm

  1. Power fault alarm immediately after energization (B exclusive alarm)

สาเหตุ: Forced reuse of old cable, cross connection between power and signal lines, internal short in connector

  1. Calibration Related Faults (Most frequent after swap)
  2. Auto-calibration aborted, stops mid-cycle, stroke error alarm

ทริกเกอร์:

Misaligned magnetic coupling, coupling slip, O-ring binding; valve stem offset during assembly

การปนเปื้อน, ice plug or spool seizure in valve body (A may tolerate marginal friction while B has tighter detection)

Incorrect mounting torque (over-tightened coupling or insufficient torque leading to slip)

Wrong valve body selection at parameter i26 (selected larger ICM size)

อาการ: Calibration halts halfway and cannot complete full close → full open travel

  1. Calibration successful, but valve fails to close tight / over-travel / cannot reach full open

สาเหตุ: Spool was not set to mid-position before calibration; worn seat, foreign debris, abnormal magnetic coupling gap

คุณสมบัติ: 4mA command does not correspond to 0% feedback, 20mA cannot reach 100%

  1. Control Signal Loop Faults (4-20มิลลิแอมป์ / 0-10วี)
  2. Control signal applied, valve stationary, position reading fixed

สาเหตุ: Wrong connection at analog input Pin E; signal GND not common with controller GND; signal type mismatch (menu set for voltage while current signal is applied, หรือในทางกลับกัน)

หมายเหตุสำคัญ: B input impedance differs from A; verify drive capability of EKC347 or PLC analog output

  1. ไม่ถูกต้อง / drifting feedback, feedback inconsistent with actual valve position

สาเหตุ: Wrong wiring at feedback Pin F; feedback loop overloaded resistance, loose GND connection, incomplete calibration

อาการ: Controller reading differs from local actuator display

  1. Valve oscillation, small continuous hunting

สาเหตุ: PID parameters inherited from A; B stepper response speed differs; poor shielding earthing causing interference; signal cable routed together with power cable

บันทึก: PID tuned for A often oscillates directly on B and requires fine adjustment

  1. Digital Output Faults (Full Open / Full Close / Fault NPN)
  2. PLC fails to receive full-open / full-close signal or signal stays permanently ON

สาเหตุ: ก & B have different common terminal definition for digital outputs. Reused old cable leads to wrong common connection; reversed external supply for NPN loop

จุดวิกฤติ: B’s three DO channels share Pin A (fault common), which is completely different from A

  1. Persistent fault output with normal valve operation

High incidence: UPS detection enabled without UPS module fitted, B interprets status as UPS fault; UPS function not disabled in menu

  1. UPS Power-Fail Hold Specific Faults (with 027H0388 fitted)
  2. Fails to move to safe position on power loss or constant UPS alarm at startup

สาเหตุ: B blue Pin IV on power plug is UPS status feedback, which does not exist on A; legacy UPS wiring incompatible; aged UPS battery

หลุมพราง: A UPS only required power feed; B requires both power and status feedback wire otherwise permanent alarm

  1. ข้อผิดพลาดในการสื่อสาร (RS485 Modbus, New for B)
  2. No Modbus data read, การสื่อสารไม่ต่อเนื่อง

สาเหตุ: Wrong wiring on 4-pin M12 communication port; missing terminating resistor; ที่อยู่ที่ซ้ำกัน; อัตรารับส่งข้อมูลไม่ตรงกัน; poor shield earthing

เคล็ดลับ: Bus port can be left unconnected if unused for analog control; avoid accidental signal connection to this port

  1. อุณหภูมิต่ำ / Site Environmental Faults (Common for NH₃ & CO₂ transcritical systems)
  2. Random position loss and slip at low temperature without fixed alarm

สาเหตุ: Molycote 55 grease not applied during assembly; missing or damaged O-ring, moisture entering magnetic coupling and freezing

คุณสมบัติ: Calibration passes at ambient temperature, random drift when cooled, temporary recovery after reboot

  1. Condensation inside connector, intermittent sporadic faults

สาเหตุ: Aged old M12 connector seal; poor crimp sealing after reworking cable, IP67 rating compromised

  1. Misleading Apparent Faults (Logic Difference, Not Actual Failure)
  2. Different valve movement at identical 4mA setpoint compared with A

Not a fault: B stroke algorithm, dead band and stepper speed parameters are independent; loop matching is required

  1. Alarm codes not found in A manual

B alarm table rewritten; many A alarm IDs do not exist on B

  1. Different local keypad operation logic

Menu navigation and manual mode entry sequence changed; commissioning personnel may mistake for actuator malfunction

  1. Fast Troubleshooting Sequence (On-site Priority)
  2. Verify every M12 pin assignment (พลัง, สัญญาณ, ยูพีเอส) first to rule out miswiring
  3. ยืนยันแหล่งจ่ายไฟ: Stable 24V DC, ≥22V at actuator terminals under load
  4. Check menu settings: ประเภทสัญญาณ (ปัจจุบัน / แรงดันไฟฟ้า), valve body model i26, UPS enable / disable
  5. Run a complete auto-calibration again
  6. Check common ground and shield bonding, ขจัดสัญญาณรบกวน
  7. Test in manual mode alone to isolate whether fault lies in actuator hardware or upstream controller signal

Danfoss ICAD Stepper Electric Actuator Full Model & รายการรหัสการสั่งซื้อ (For ICM Refrigeration Valves)

คำอธิบาย: ICAD = Stepper motor actuator for ICM / ICMTS regulating valves and CVE pilot valves. Divided into A-series (เก่า, ล้าสมัย), B-series (ใหม่, คล่องแคล่ว), TS transcritical dedicated variant. All models run on 24V DC.

  1. A-series (รุ่นเก่า, 027H9xxxx, ล้าสมัย)
แบบอย่างรหัสการสั่งซื้อCompatible Valveหมายเหตุ
ไอแคด600เอ027H9065ICM20/25/32รุ่นปัจจุบันของคุณ, segment LCD, no RS485, no Bluetooth
ไอแคด600เอ027H9075ICM20/25/32Same ICAD600A, version variation
ไอแคด600เอ027H9120ICM20/25/32ข้อกำหนดเดียวกัน
ICAD600A-TS027H9078ICMTS20~ICMTS80CO₂ transcritical dedicated
ICAD900A027H9101Large bore ICMTSCO₂ transcritical dedicated
ICAD1200A027H9077ICM40/50/65/100/125/150High torque A version
ICAD1200A027H9122ICM40/50/65/100/125/150Same ICAD1200A
  1. B-series (Current active, 027H04xx, OLED + บลูทูธ, ตัวเลือก RS485 / อีเทอร์เน็ต)

ICAD600B (For ICM20 / ICM25 / ICM32)

แบบอย่างรหัสการสั่งซื้อการกำหนดค่า
ICAD600B027H0485แสดง, บลูทูธ, อาร์เอส485 (ที่พบบ่อยที่สุด, direct replacement for A)
ICAD600B027H0486แสดง, บลูทูธ, อีเทอร์เน็ต
ICAD600B027H0488ไม่มีการแสดงผล, บลูทูธ, อาร์เอส485
ICAD600B027H0489ไม่มีการแสดงผล, บลูทูธ, อีเทอร์เน็ต

ICAD1200B (For ICM40~ICM150)

แบบอย่างรหัสการสั่งซื้อการกำหนดค่า
ICAD1200B027H0490แสดง, บลูทูธ, อาร์เอส485
ICAD1200B027H0491แสดง, บลูทูธ, อีเทอร์เน็ต
ICAD1200B027H0492ไม่มีการแสดงผล, บลูทูธ, อีเทอร์เน็ต
ICAD1200B027H0493ไม่มีการแสดงผล, บลูทูธ, อาร์เอส485

ICAD600B-TS:CO₂ transcritical dedicated, separate order family for ICMTS valve bodies

  1. เครื่องประดับ & Cable Order Codes (ICAD compatible)
คำอธิบายรหัสการสั่งซื้อบันทึก
ICAD UPS power-fail hold module027H0388Works with A & บี (B has UPS status detection pin)
Pre-assembled cable 1.5m027H0426M12 power + M12 signal, B-series only
Pre-assembled cable 3m027H0438M12 power + M12 signal
Pre-assembled cable 10m027H0427M12 power + M12 signal
Pre-assembled cable 15m027H0435M12 power + M12 signal
M12 connector spare kit027H0430Signal plug spare part
Protective dust cap027H0431Top cover protection for actuator
  1. การอ้างอิงการเลือกด่วน

ICM20 / ICM25 / ICM32 → ICAD600A (ล้าสมัย) / ICAD600B (การทดแทน)

ICM40~ICM150 → ICAD1200A (ล้าสมัย) / ICAD1200B (การทดแทน)

ICMTS (CO₂ transcritical) → ICAD600A-TS / ICAD900A / ICAD600B-TS

  1. หมายเหตุสำคัญ
  2. All A-series (027H9xxx) ถูกยกเลิก. B-series is preferred for replacement. สามารถเปลี่ยนได้ทางกลไก, pin assignment incompatible; old cable must not be plugged directly.
  3. B-series: RS485 variant widely used for site retrofit; Ethernet variant for building automation and remote SCADA
  4. TS variants have special internal seals and firmware tuned for CO₂ transcritical operation; standard ICAD600B cannot substitute directly
  5. All ICAD actuators run on 24V DC. 24V AC supply is strictly prohibited

ก่อนหน้า:

ต่อไป:

ทิ้งคำตอบไว้

ฝากข้อความ