เพรสเชอร์เซนเซอร์เอนกประสงค์ OMRON E8EB-10C - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

วีแชท: +86-13184948252 วอทส์แอพพ์: 0086-13811255435 อีเมล: kent@bestcontactor.com

เกี่ยวกับ ติดต่อ |

เพรสเชอร์เซนเซอร์เอนกประสงค์ OMRON E8EB-10C - คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง

บมจ/

เพรสเชอร์เซนเซอร์เอนกประสงค์ OMRON E8EB-10C

ประเภทสินค้า: Integrated Pressure Sensor (สวิตช์ความดัน) | สถานะ: Discontinued by Manufacturer Omron E8EB series integrated pressure sensor with analog + การสลับเอาต์พุต, positive pressure type, เอาต์พุต NPN. ✅ Core Specifications Pressure Range: 0~1 MPa (0~10 kgf/cm², 0~142 psi) พาวเวอร์ซัพพลาย: DC24V Switch Output: ตัวรวบรวมแบบเปิด NPN; สูงสุด. โหลดปัจจุบัน 80 มิลลิแอมป์, สูงสุด. voltage DC30V ...

  • รายละเอียดสินค้า

ประเภทสินค้า: แบบบูรณาการ เซ็นเซอร์ความดัน (สวิตช์ความดัน) | สถานะ: ถูกยกเลิกโดยผู้ผลิต

ออมรอน E8EB series integrated pressure sensor with analog + การสลับเอาต์พุต, positive pressure type, เอาต์พุต NPN.

✅ ข้อมูลจำเพาะหลัก

ช่วงความดัน: 0~1 MPa (0~10 kgf/cm², 0~142 psi)

พาวเวอร์ซัพพลาย: ดีซี24วี

สลับเอาต์พุต: ตัวรวบรวมแบบเปิด NPN; สูงสุด. โหลดปัจจุบัน 80 มิลลิแอมป์, สูงสุด. voltage DC30V

Linear Analog Output: 1~5 V, Output impedance 20Ω, นาที. load resistance 10 kΩ

เวลาตอบสนอง: ≤5 ms

การบริโภคในปัจจุบัน: 20 มิลลิแอมป์

Pressure Port: RC(ปตท)1/4

ระดับการป้องกัน: IP54

อุณหภูมิในการทำงาน: -10℃~+55℃ (ไม่มีไอซิ่ง); พื้นที่จัดเก็บ: -25℃~70℃

ตัวบ่งชี้: ไฟแอลอีดีสีแดง (lights up when output is ON)

เคเบิล: สายไฟมาตรฐาน 2 ม

สื่อ: Dry air, non-corrosive gas (Not suitable for corrosive liquid)

📌 คำอธิบายรหัสรุ่น (E8EB Series)

E8EB = Series Code

10 = Range 0~1MPa

C = NPN output; Suffix B = PNP (Model E8EB-10B)

01 = 0~0.1MPa; N0 = Vacuum type

🔁 Official Replacement Model: E8F2-B10C

รายการE8EB-10C (รุ่นเก่า)E8F2-B10C (การทดแทน)
ช่วงความดัน0~1MPa0~1MPa
เอาท์พุตตัวรวบรวมแบบเปิด NPN + 1~5V linear analogเอ็นพีเอ็น, dual independent switch outputs + 1~5V linear analog
การบริโภคในปัจจุบัน20มิลลิแอมป์70มิลลิแอมป์
โหลดปัจจุบัน80มิลลิแอมป์30มิลลิแอมป์
การปรับPotentiometer adjustment, ไม่มีจอแสดงผลดิจิตอลจอแสดงผลดิจิตอล + bar graph, one-touch teaching setup
ขนาดการติดตั้งDifferent footprint and mounting holesCannot be plug-and-play; bracket and piping need modification

⚠️ ประกาศสำคัญ: Direct plug-in replacement is NOT feasible. ความสามารถในการรับน้ำหนัก, current draw and mounting dimensions differ; PLC wiring logic must be verified.

🧾 Pin Assignment (4-Core Cable)

สีน้ำตาล: ดีซี24วี+

สีฟ้า: 0วี (จีเอ็นดี)

สีขาว: ON/OFF Switch Output (เอ็นพีเอ็น)

สีดำ: 1~5V Linear Analog Output

🛠️ Troubleshooting Checklist

  1. ไม่มีเอาท์พุต: Check 24V supply and blue wire ground; confirm pressure exceeds set threshold
  2. Abnormal analog signal: Load resistance ≥10kΩ; low-resistance loads are prohibited
  3. ไฟ LED ไม่ติด: Pressure not reaching actuation point, or incorrect hysteresis setting
  4. สัญญาณดริฟท์: Water/oil contamination in air source, out-of-range temperature, or pressure surge exceeding full scale

📎 ข้อมูลเพิ่มเติม

ใช้แล้ว / second-hand units are still available on the aftermarket; ไม่มีสต็อกเดิมใหม่เอี่ยม

การอ้างอิงรหัส HS: 90262090 (Gas pressure measuring sensor)

โมเดลทางเลือก: E8F2 series, E8CC series digital pressure sensors

E8EB-10C → E8F2-B10C Retrofit Wiring List (4-core old → 5-core new)

E8EB: 4-แกนกลาง; E8F2-B10C: 5-แกนกลาง (dual switch outputs + 1~5V analog), เอ็นพีเอ็น, 0~1MPa, ดีซี24วี

Goal: Retain the original circuit: 1 switch signal + 1~5V analog; leave the second output unused and insulated.

  1. Wire Color Matching Table
E8EB-10C (เก่า, 4-แกนกลาง)การทำงานE8F2-B10C (ใหม่, 5-แกนกลาง)การทำงานConnection Plan
สีน้ำตาลดีซี24วี+สีน้ำตาลดีซี24วี+✅ Direct connection
สีฟ้า0วี จีเอ็นดีสีฟ้า0วี จีเอ็นดี✅ Direct connection
สีขาวSwitch Output OUT1 (เอ็นพีเอ็น)สีขาว (ออก1)สลับเอาต์พุต 1 (เอ็นพีเอ็น)✅ Connect to original PLC input point (keep original pressure signal logic)
สีดำ1~5V Analog Signalสีเทา1~5V Analog Output✅ Original black wire → new grey wire
—ไม่มีสีขาว (ออก2)Independent Switch Output 2 (เอ็นพีเอ็น)⚠️ Leave unused, wrap with insulation; short-circuit strictly forbidden

การแจ้งเตือนที่สำคัญ: The analog output on E8F2 is the grey wire NOT the white wire, this is the most common wiring mistake. If analog signal is not required, insulate the grey wire separately.

  1. ขั้นตอนการต่อสายไฟ
  2. Cut off all power; confirm PLC and sensor power circuits are fully de-energized
  3. Disconnect old sensor terminals and record Brown/Blue/White/Black channel mapping
  4. วงจรไฟฟ้า: Brown to Brown, Blue to Blue (แหล่งจ่ายไฟ DC24V)
  5. Switch signal: Original white wire → E8F2 OUT1 white wire (match original PLC logic)
  6. Analog signal: Original black (1~5V) → E8F2 grey wire
  7. E8F2 OUT2 white wire: Seal with heat-shrink tube/insulation tape, keep isolated
  8. Inspect wiring for short circuits and exposed copper before powering on.
  9. Parameter Differences & PLC Program Verification Checklist (บังคับ)
รายการE8EB-10CE8F2-B10CRetrofit Risk Point
Current Draw20มิลลิแอมป์70มิลลิแอมป์Recheck 24V power supply capacity; insufficient margin will cause voltage drop
Switch Load Capacity80มิลลิแอมป์30มิลลิแอมป์PLC digital input is fine; if the original circuit drives a relay directly, the relay cannot be reused; reduce load current
Thread PortRC(ปตท)1/4ร(ปตท)1/8Must install reducing adapter; cannot thread directly
การติดตั้งOriginal bracket28mm panel / E89-F3 bracketHole positions do not match; new holes or adapter plate required
วิธีการตั้งค่าPotentiometer adjustmentเมนู / teaching setupPressure setpoints and hysteresis must be reconfigured; old potentiometer values are invalid
ช่องสัญญาณเอาท์พุตSingle switchTwo independent switchesProgram only uses OUT1; disable OUT2
  1. Power-On Commissioning Sequence
  2. No-load power-on first; confirm E8F2 digital display lights up normally
  3. เข้าเมนู: Set actuation mode, pressure setpoint and hysteresis to match the original E8EB values
  4. Pressurize and test: Verify OUT1 triggers PLC input correctly
  5. Analog test: 0MPa ≈1V, 1MPa≈5V; confirm linear reading on PLC analog channel
  6. Stabilize signal: Enable anti-chatter filter to prevent false triggering caused by air pressure fluctuation.
  7. การแก้ไขปัญหาอย่างรวดเร็ว

No analog reading: Grey wire disconnected or misconnected to OUT2 white wire

Cannot drive load: Load current exceeds 30mA rating

No switching action: Parameters not reconfigured; factory default values differ from old sensor

การรั่วไหลของอากาศ: Thread mismatch; missing reducing adapter

Full Commissioning Procedure: E8EB-10C Upgrade to E8F2-B10C (Match Original System Logic)

วัตถุประสงค์: OUT1 replaces the old E8EB switch point; grey wire 1~5V analog keeps the original PLC analog channel; OUT2 remains unused.

ปุ่ม: ชุด (Confirm/Enter), Up ▲, Down ▼; Press and hold SET for 2s to enter main menu; short press SET for pressure setting.

ขั้นตอน 1: Pre-Power Check (Prevent PLC Input Burnout)

  1. ตรวจสอบการเดินสายไฟ: Brown=24V+, Blue=0V, White=OUT1, Grey=Analog, OUT2 white wire fully insulated
  2. Load check: E8F2 NPN output max. 30มิลลิแอมป์. Do not drive relays directly. Add an intermediate relay if the old circuit had a relay load
  3. ท่อ: Install PT1/8 to PT1/4 reducing adapter with thread sealant; test for air leakage before commissioning
  4. Air source: Use dry compressed air free of excessive water and oil; working pressure cannot exceed 1MPa full scale
  5. ฝั่งบมจ: Analog input impedance ≥10kΩ; low-resistance loads are prohibited.

ขั้นตอน 2: No-Load Power On & รีเซ็ตเป็นศูนย์ (Zero Pressure Condition)

  1. Power the sensor alone, without air pressure applied, wait for display stabilization
  2. Zero point reset (zero pressure calibration): Press ▲+▼ simultaneously to reset zero reading

บันทึก: Zero reset must be done at zero pressure; calibration under pressure will lead to permanent drift.

ขั้นตอน 3: Basic Parameter Setup (Hold SET 2s to enter main menu)

  1. หน่วย (unt): Select MPa (consistent with old sensor; kPa is also acceptable)
  2. โหมดการทำงาน (m-a): Select HYS (Hysteresis Mode, same as E8EB); avoid Window Mode
  3. ลอจิกเอาท์พุต (ope): เอ็นพีเอ็น, เปิดตามปกติ (เลขที่); output ON when pressure exceeds set value
  4. Anti-chatter Filter: Set to STND (มาตรฐาน); select longer filtering if air pulsation is severe to avoid signal chattering
  5. บันทึก: Hold SET 2s to return to measurement screen.

Only configure OUT1; leave OUT2 parameters unchanged as it remains unused.

ขั้นตอน 4: Pressure Setpoint Configuration (2 ตัวเลือก: Manual Input / Teaching Mode; Teaching is Recommended)

ตัวเลือก ก: 2-การสอนแบบจุด (Best for replicating old E8EB trigger points)

  1. Short press SET to enter pressure setting → select OUT1 → select 2-point teaching
  2. Slowly raise pressure to ON actuation pressure, stabilize and press SET to save the ON point
  3. Slowly reduce pressure to OFF release pressure, stabilize and press SET to save hysteresis OFF point
  4. Hold SET to save and exit.

ตัวอย่าง: Original E8EB turns ON at 0.5MPa and OFF at 0.4MPa; teach these two pressure values directly on site.

ตัวเลือก ข: Manual Value Entry (If original setpoints are known)

  1. Short press SET → enter OUT1 ON value → adjust value with ▲▼
  2. Press SET to switch to OUT1 OFF value → set hysteresis (ปิด < บน)
  3. Press SET again to jump to OUT2; skip without modification
  4. Hold SET to save and exit.

Recommended hysteresis: Keep consistent with original setting to avoid frequent cycling; factory default hysteresis = 3%FS (30kPa for 0~1MPa range).

ขั้นตอน 5: Switch Output Test (ออก1, PLC Digital Input)

  1. Gradually increase pressure; check E8F2 OUT1 indicator + อินพุต PLC: ON when pressure ≥ setpoint
  2. Gradually reduce pressure; input turns OFF when pressure drops below OFF threshold
  3. Repeat 3 times to confirm:

No flickering or intermittent signal

Trigger action fully consistent with the old sensor

No premature or delayed switching

การแก้ไขปัญหา: Frequent chattering → increase filter time and hysteresis; no action → reverse NO/NC output logic.

ขั้นตอน 6: 1~5V Analog Channel Calibration (Grey Wire, Critical Step)

พิสัย: 0~1MPa = 1V ~ 5V

0MPa: Theoretical output ≈1.0V

0.5MPa: Theoretical output ≈3.0V

1.0MPa: Theoretical output ≈5.0V

ขั้นตอนการว่าจ้าง:

  1. Zero pressure: Confirm PLC analog reading ≈1V
  2. Pressurize to 0.5MPa and cross-check reading
  3. Full scale 1MPa: Verify output ≈5.0V

⚠️หมายเหตุสำคัญ: E8F2 analog output is pre-calibrated for linearity. No re-calibration on PLC side is required. If deviation occurs, redo zero reset first and check load resistance.

ขั้นตอน 7: Full System On-Line Test (Automatic Machine Cycle)

  1. Switch equipment to automatic mode; verify pressure interlock and alarm logic work correctly
  2. Run continuously for 5~10 minutes; confirm output stays stable under pressure fluctuation
  3. Record actuation pressure, hysteresis and filter parameters in engineering change records
  4. Add pressure buffer/throttle on the air inlet if pressure surge occurs to prevent overpressure damage.

ขั้นตอน 8: ตารางการแก้ไขปัญหาข้อผิดพลาด

อาการสาเหตุที่แท้จริงการเยียวยา
OUT1 never switches ONON setpoint too high; NO/NC logic reversedRecheck set value; modify ope output mode
Switch signal flickers continuouslyAir source pulsation; filter time too shortExtend response filter; increase hysteresis value
Analog signal stuck fixed at 1VGrey wire broken/disconnected; load resistance too lowInspect grey wire; ensure PLC input resistance ≥10kΩ
Zero reading drifts constantlyZero reset performed under pressure; air contains water/oilRe-zero at zero pressure; install air filter for moisture removal
Output stays permanently ON after power-upOFF value set higher than ON value (parameter reversed)Ensure OFF pressure < ON pressure
PLC input channel burned outLoad current exceeds 30mA ratingRemove direct relay drive; เพิ่มรีเลย์กลาง

Full Model List of OMRON General-Purpose Gas Pressure Sensors (นิวเมติก / คอมเพรสเซอร์ / เครื่องดูดฝุ่น, Dry Air Only)

บันทึก: All models are Gauge Pressure. เอาท์พุต: NPN/PNP switch + 1~5V analog. Split into Discontinued Legacy Models + Official Replacement Models, suitable for spare part replacement, บอม & foreign trade.

คำนิยามคำต่อท้าย: ค=เอ็นพีเอ็น; บี=พีเอ็นพี; A01=0~100kPa; B10=0~1MPa; AN0=Vacuum 0~-101kPa.

  1. E8EB Series (ไม่มีการแสดงผล, การปรับโพเทนชิออมิเตอร์, ยกเลิกแล้ว)

4-core lead wire, RC1/4 thread, single switch + 1~5V analog; 20mA current draw, สูงสุด. load 80mA.

แบบอย่างช่วงความดันเอาท์พุต
E8EB-01ค0~100กิโลปาสคาล (0.1MPa)เอ็นพีเอ็น
E8EB-01บี0~100กิโลปาสคาล (0.1MPa)พีเอ็นพี
E8EB-10C0~1MPaเอ็นพีเอ็น (Main Model in This Retrofit)
E8EB-10B0~1MPaพีเอ็นพี
E8EB-N0C2B0~-100kPa Vacuumเอ็นพีเอ็น
E8EB-N0B2B0~-100kPa Vacuumพีเอ็นพี
  1. E8F2 Series (จอแสดงผลดิจิตอล, official replacement for E8EB/E8CC, ยกเลิกแล้ว)

5-สายเคเบิลหลัก, PT1/8 thread, dual independent switch outputs + 1~5V analog; 70mA power consumption; single channel max. load 30mA; one-touch teaching programming.

แบบอย่างช่วงความดันเอาท์พุต
E8F2-A01C0~100กิโลปาสคาลเอ็นพีเอ็น (E8EB-01C Replacement)
E8F2-A01B0~100กิโลปาสคาลพีเอ็นพี
E8F2-B10C0~1MPaเอ็นพีเอ็น (Direct replacement for E8EB-10C)
E8F2-B10B0~1MPaพีเอ็นพี
E8F2-AN0C0~-101kPa Vacuumเอ็นพีเอ็น
E8F2-AN0B0~-101kPa Vacuumพีเอ็นพี
  1. E8CC Series (Slim digital type, predecessor of E8EB, ยกเลิกแล้ว)

With digital display, single switch + 1~5V analog; การติดตั้งราง DIN; replaced by E8F2.

แบบอย่างช่วงความดันเอาท์พุต
E8CC-A01C0~100กิโลปาสคาลเอ็นพีเอ็น
E8CC-B10C0~1MPaเอ็นพีเอ็น
E8CC-AN0C0~-101kPa Vacuumเอ็นพีเอ็น
  1. E8MS / E8M Split Type (Sensor Head + คอนโทรลเลอร์, ยกเลิกแล้ว)

Pure 1~5V analog signal without built-in switch; requires E8M controller for multi-channel pressure acquisition.

แบบอย่างช่วงความดันพิมพ์
E8MS-010~100กิโลปาสคาลPositive Pressure Probe
E8MS-100~1MPaPositive Pressure Probe
E8MS-N00~-101kPa VacuumVacuum Probe
E8MS-N1-101~101kPa Compound PressureCompound Pressure Transducer
E8M-100~1MPaE8M Independent Probe
E8M-N00~-101kPa VacuumVacuum Probe
E8M-A10~1000PaMicro Differential Pressure
  1. E8AA Series (Stainless Steel Diaphragm Special Model, ยกเลิกแล้ว)

Limited use for liquid / slightly corrosive gas applications.

แบบอย่างช่วงความดัน
E8AA-M050~500kPa
E8AA-M100~1MPa
  1. E8Y / E8Y-L Micro-Pressure Sensors (Differential Pressure for Duct & พัดลม, Not General Pneumatic Type)

Pa-level low pressure (200Pa ~5kPa); some models with 4-20mA output; used for air duct and filter differential pressure monitoring only.

✅ Cross Reference Table (Spare Part Replacement Priority)

รุ่นเก่าการเปลี่ยนที่แนะนำความแตกต่างที่สำคัญ
E8EB-01คE8F2-A01CPT1/8 thread, dual outputs, load current reduced to 30mA
E8EB-10CE8F2-B10CFull retrofit plan covered above
E8EB-N0C2BE8F2-AN0CVacuum pressure type
E8CC-A01CE8F2-A01CDifferent mounting footprint

📌 General Notes

  1. สื่อ: Dry non-corrosive air; Not for liquid or strong corrosive gas
  2. Analog Output Standard: 1~5V (1V at zero pressure, 5V at full scale)
  3. Thread Spec: E8EB = RC1/4; E8F2 = R1/8; reducing adapter is mandatory for retrofit
  4. พาวเวอร์ซัพพลาย: ดีซี24วี
  5. All listed models are discontinued; เฉพาะสต๊อกส่วนเกินเท่านั้น & หน่วยมือสองที่มีอยู่. New projects shall select the latest OMRON E8F series.

ก่อนหน้า:

ทิ้งคำตอบไว้

ฝากข้อความ