Siemens 6EP1333-2BA20 Single-Phase DIN Rail Power Supply

Vollständiger Produktname: SITOP PSU100S 24V DC /5A Regulated Stromversorgung

Order Code Definition:

6EP = SITOP power supply family; 1333=24V 5A; 2BA20=PSU100S version, No Ex explosion-proof certification

✅ Grundlegende elektrische Spezifikationen

Eingang

Stromversorgung: Single-phase AC 120/230V, 50/60Hz

Spannungsbereich: AC 85–132V (120V range) / 170–264V (230V range), Not full wide automatic range

Nenneingangsstrom: 1.3A at 230V; 2.1A at 120V

Built-in input fuse; Recommended circuit breaker: B10A / C6A

Wartezeit: ≥20ms at rated load

Ausgabe

Bewertet: DC24V, 5A, 120W

Output adjustable range: 22.8 ~ 28V (via potentiometer on housing)

Static accuracy: ±3 %; Maximum ripple 150mV peak-to-peak

Überlastfähigkeit: 150% Nennstrom für 5 seconds per minute; Continuous operation at 120% laden

Statusanzeige: Green LED (24V OK) + Normally-open relay alarm contact (closed when power healthy)

📐 Mechanical & Umweltfreundlich

Montage: DIN-35-mm-Schienenmontage, natural air cooling

Gewicht: 0.4kg

Betriebstemperatur: -10 ~ +70℃; Derating starts above 60℃ (3%/K); Upper limit drops to 50℃ if output >24V

Lagertemperatur: -25 ~ +85℃; Humidity class EN60721 3K3

Ursprungsland: Österreich; HS-Code: 85044083

🧩 Features

1. Isolated industrial switching power supply, standard 24V power source for PLC, sensors and valve islands
2. Relay signal contact, can be connected to PLC for power fault diagnosis
3. Parallel connection for current expansion (Max ambient temperature derate by 10℃ when paralleled)
4. Schutzmaßnahmen: Überstrom, Überspannung, Übertemperaturschutz
5. Zertifizierungen: UL508, CE, RoHS; This model no longer supports Ex certification

⚠️ Alternative Selections

Smaller model in same series: 6EP1332-2BA20 (24V/2,5A)

Larger model in same series: 6EP1334-2BA20 (24V/10A)

Domestic alternatives reference: Meanwell DR-120-24, Phoenix QUINT-PS/1AC/24DC/5

🛠️ Common Troubleshooting

1. No green LED: Check AC input voltage, Interne Sicherung durchgebrannt; Output short-circuit protection latch, zum Zurücksetzen aus- und wieder einschalten
2. Spannungsabfall unter Last: Niedrige Eingangsspannung, overtemperature derating, continuous load exceeding 120% rating
3. Alarm relay not closed: Power supply under protection state or output voltage too low

Application Scenarios for 6EP1333-2BA20 (SITOP PSU100S 24V/5A)

Kernpositionierung: Single-phase AC to 24VDC SELV control power supply inside small control cabinets, to power PLC, I/O-Module, Sensoren, Ventile, HMI and other industrial components. Equipped with power-good relay alarm contact, suitable for stand-alone / small station automation, DIN-Schienenmontage.

1. Maschinenbau / Stand-alone Automation (Am häufigsten)
2. Verpackungsmaschinen: Vertikale Verpackungsmaschinen, Etikettierer, Kofferpacker, heat shrink machines. Power supply for S7-1200/1500, fotoelektrische Sensoren, Näherungssensoren, Magnetventile, safety relays and touch screens; 5A capacity matches I/O loops of medium-small standalone machines.
3. Fördern & Sortierausrüstung: Kleine Förderbänder, Rollenlinien, Transfermaschinen. Supply I/O modules, Encoder, fotoelektrische Sensoren, pneumatic valve islands; Support parallel expansion.
4. Spritzguss / stamping auxiliary equipment: Manipulator control cabinet, material feeder, mold temperature controller cabinet; Resist grid fluctuation, suitable for loads with start impulse current.
5. Machine tool auxiliary control box: Small special machines, fixture control cabinet, power for sensors, indicator lights and safety circuits.
6. Prozessautomatisierung (Wasseraufbereitung, HVAC, Kommunal)
7. Wasseraufbereitung: Small water purification equipment, chemisches dosiersystem, reclaimed water reuse control cabinet. SPS + analog transmitters, Niveauschalter, Magnetventile; Relay alarm contact connects to PLC for remote power failure alarm.
8. HVAC: Building air handling units, Frischlufteinheiten, exhaust fan control cabinet; Power DDC, Differenzdrucksensoren, electric actuators.
9. Municipal small pump stations, sewage monitoring stations: Field control box, sensor acquisition + remote communication module.

Notiz: This model without Ex certification; If used in explosive hazardous area, power supply body must be installed inside IP54 or higher explosion-proof cabinet.

3. Logistik, Lagerung, Auxiliary Stations of Automated Production Lines

Small workstation control cabinet of mini AS/RS, AGV ground station, scanning inspection station; Power ET200SP remote I/O, fotoelektrische Sensoren, RFID readers, Kontrollleuchten.

Automotive component assembly stations, test fixture cabinets, standalone test benches.

4. Andere Branchen
5. Essen & pharmazeutisch: Small filling and inspection equipment control cabinet; CE/UL compliant, suitable for standalone control in clean rooms.
6. Laboratory test equipment, non-standard automatic test benches.
7. PV / energy storage auxiliary control cabinet: Local signal acquisition cabinet (only for control circuit, not power circuit).

✅ Typical Load Combination Reference (5A Capacity)

S7-1200 CPU + 8~16 DI/DO points + HMI + several proximity/photoelectric sensors + 2~4 pcs 24V solenoid valves + Sicherheitsrelais.

Vorsicht: Solenoid valve has high inrush current, reserve margin during selection; High-power valves require separate power loop.

⚠️ Not Recommended Applications

1. High-power 24V motors, heavy heating loads (This is control power supply, not power supply for high power loads)
2. 3-phase input system (unless single-phase power is tapped from front end)
3. Heavy corrosion environment, direct outdoor exposure (must be installed inside control cabinet)
4. Direct installation in hazardous explosive area
5. Main power supply for large systems (10A+ model or redundant scheme recommended)

✅ Selection Key Points

Vorteile: Power-good relay output, 150% short-time overload capacity, kompakte DIN-Schienenmontage, SELV safety isolation, ideal for small control cabinets requiring power status monitoring.

Kapazitätserweiterung: Multiple units in parallel to increase total output current; Reduce maximum ambient temperature when paralleling.

Full Model List of SITOP PSU100S Series (Single-phase AC Input, DIN-Schienen-Netzteil)

Alle Modelle: Input AC 120/230V (85–132V /170–264V), equipped with Power-good relay alarm contact, natürliche Kühlung, DIN35-Schienenmontage.

24V DC Output Series (Am häufigsten, sub-series of your model)

12V DC Output Series

Derived SIPLUS Wide-temperature Coated Version (Optional, not standard PSU100S)

6AG1334-2BA20-4AA0: SIPLUS PS PSU100S 24V/10A, conformal coating, Betriebstemperatur -25 ~ +70℃, for high humidity and corrosive environments (Eisenbahn, outdoor cabinet)

✅ Common Features of Series

1. Relay alarm output (Power-good dry contact for PLC diagnosis)
2. Kurzzeitige Überlastung: 150% laden für 5 Sekunden, handles solenoid valve impulse current
3. Schutz: Überstrom, Überspannung, Übertemperaturschutz
4. Multiple units can be paralleled to increase output current (Derate ambient temperature upper limit)
5. Zertifizierungen: CE, UL508, RoHS; No Ex explosion-proof certification

⚠️ Distinction Reminder

PSU100S ≠ SITOP smart / PSU100C / PSU6200, nicht verwechseln:

PSU100S: With relay alarm contact, list above;

SITOP smart: Without relay alarm, geringere Kosten;

PSU6200: Neue Generation, with communication diagnosis function.

Input Voltage Specifications of 6EP1333-2BA20

Single-phase AC, Automatic dual-range switching, not continuous 85~264V full wide range

Reichweite 1 (120V range): AC 85V ～ 132V

Reichweite 2 (230V range): AC 170V ～ 264V

Rated input: AC 120V / 230V

Input frequency: 47～63Hz (50/60Hz-kompatibel)

Wichtige Hinweise

1. Voltage gap: Cannot operate stably when AC voltage between 132V ~170V. Power supply will not work reliably if grid voltage falls within this gap, must pay attention during selection.
2. Power supply automatically identifies voltage range internally, no manual DIP switch required.
3. Wartezeit: ≥20ms at rated load and rated input voltage.
4. In domestic 3-phase cabinet, single-phase 220V tapped (170~264V range), falls into 230V range and works properly.

Housing Dimensions of 6EP1333-2BA20 (B × H × T)

50 mm × 125 mm × 120 mm

Breite (DIN rail direction): 50 mm

Höhe (Vertikale): 125 mm

Tiefe (into cabinet): 120 mm

Installation Clearance (Anforderung an die Wärmeableitung, critical for cabinet layout)

Top clearance: 50 mm

Bottom clearance: 50 mm

Links & Rechts: 0 mm, can be mounted side-by-side with other modules

Mount on EN 60715 standard 35mm DIN rail, wall mounting not supported.

Gewicht

Nettogewicht: Ca. 0.4 kg

Dimension comparison of PSU100S series (for cabinet layout)