Allen‑Bradley 20G11NC011AA0NNNNN AC Drive

PowerFlex 755 Air-Cooled AC Unidad de frecuencia variable (VFD)

Ciclo vital: Obsoleto (Last order date: 2024‑06‑30). Direct OEM replacement part number: 20G11NC011JA0NNNNN

1. Catalog Number Breakdown (20G Series Coding Rule)

20GRAMO 1 1 N C 011 A 0 NNNNN

2. Especificaciones eléctricas clave

Corriente nominal: 11.5A

Clase de voltaje: 3-phase 400V AC

Clasificación de potencia:

DAKOTA DEL NORTE (Servicio normal): 5.5kilovatios

alta definición (Servicio pesado): 4kilovatios

Tamaño del marco: Marco 2

Enfriamiento: Refrigeración por aire forzado

Comunicación: Embedded EtherNet/IP (DLR ring support)

Dynamic Braking: Built-in DB transistor, Se requiere resistencia de frenado externa

Clasificación del gabinete: IP20 (solo para montaje en gabinete)

Aporte: AC main circuit with brought-out DC bus terminals, suitable for common DC bus applications

3. Aplicaciones típicas

Transportadores, fans, zapatillas, extruders and general-purpose industrial motor speed control; supports multi-axis EtherNet/IP motion control and can share the same network with Kinetix servo drives.

4. Hardware & Notas de mantenimiento
5. Obsolete notice: After discontinuation of AA0 suffix legacy units, JA0 is the drop-in compatible replacement. Dimensiones de montaje, I/O and program parameters are fully compatible for direct replacement.
6. Accesorios opcionales: HIM keypad (20‑750‑HIM), input EMC filter, dynamic braking resistor, Desconexión de par segura (STO) módulo.
7. Puntos de falla comunes: Fan aging, DC bus capacitor degradation, ESD damage on EtherNet/IP port; for spare part replacement, prioritize OEM JA0 version.
8. Domestic Alternative Reference (Same rating 400V /11.5A VFD)

Innovación MD880, V&T AC800, Xinje DS500. Hardware replacement is feasible, but communication program, parameter groups and terminal definitions require re-commissioning. Cannot directly inherit the original Rockwell EtherNet/IP motion link.

6. Referencia del código HS

8504409990 (Otros convertidores estáticos, general classification for VFDs. Final customs classification subject to local customs authority.)

PowerFlex755 (20G11NC011AA0NNNNN) Power-On Commissioning Parameter List

Aplicable: 400V, ND 5.5kW / HD 4kW, embedded EtherNet/IP, integrated braking transistor. Estructura: Pre-power-on inspection → Factory reset → Motor nameplate data → Control mode → Start / Speed reference source → Accel/Decel & límites & protection → Autotune → EtherNet/IP communication → Dynamic braking & fault strategy → Monitoring parameters

Nota: Parameter numbers refer to Port0 (drive native parameters). Actual values from motor nameplate must be entered on site. Italic values below are examples.

1. Pre-Power-On Hardware Check (Not parameters, mandatory before commissioning)
2. Circuito principal: 3-phase input R/S/T, output U/V/W, DC bus, braking resistor wiring and earthing.
3. circuito de control: 24V control supply, STO safety terminals must be shorted (short required if no STO module, otherwise safety fault alarm).
4. Motor decoupling recommended: Disconnect mechanical load before initial autotune.
5. Rating verification: Drive rated 11.5A, match motor rated current.
6. Factory Reset (Nuevo proyecto / After repair)

3. Motor Nameplate Parameters (Crítico, enter from nameplate)

4. Modo de control (TotalFORCE, for induction motors)

5. Command Source & Speed Reference Source (Select ONE: Control de terminales / EtherNet/IP Network Control)

Option A: EtherNet/IP Network Control (Built-in port standard on this unit, most common for projects)

Option B: Local Terminal Control (Commissioning test / Standalone test)

6. Accel / Desacelerar & Limit Parameters

7. Actual / Torque Protection Parameters

8. Motor Autotune (Crítico! Run after entering nameplate data)

After successful autotune, parameter 70 automatically returns to Ready 0. If autotune fails, comprobar el cableado, nameplate entries and short-circuit to earth.

9. Embedded EtherNet/IP Communication Parameters (Port13 Embedded Adapter)

Hardware DIP switch: All DIPs set to 0 to allow software-configured IP. If DIPs are non-zero, IP is determined by hardware switches.

10. Dynamic Braking Parameters (A suffix = integrated DB transistor on this model)

11. Auto Restart on Fault (Opcional, safety hazard risk)

12. Read-only Monitoring Parameters (For observation only, no write)

13. Standard Commissioning Procedure
14. Power off → Factory reset parameters → Apply power
15. Enter all motor nameplate parameters
16. Configure control mode, command source and reference source
17. Set accel/decel, limits and overload protection
18. Run motor autotune with load decoupled, confirm autotune success
19. Ethernet/IP: Set IP address, download PLC project, establish I/O connection
20. No-load jog test, verify rotation direction, current and speed
21. Loaded trial run, fine-tune accel/decel and torque limits
22. Save parameters to drive (parameter backup), export via Studio5000
23. Record and archive full parameter set
24. Common Commissioning Pitfalls
25. STO safety terminals: 20G11NC011AA0NNNNN has no STO module; STO jumpers on control board must be shorted, otherwise safety fault on power-up.
26. Autotune fault: Check for open 3-phase motor wiring, nameplate data entry and earth short circuit.
27. Replacement 20G11NC011AA0NNNNN → 20G11NC011JA0NNNNN: Parameters can be uploaded/downloaded directly, nearly fully compatible; only verify firmware version.

4. High inertia loads: Extend deceleration time or select higher rated braking resistor