モデル: IC693ALG392C
タイプ: Analog Voltage / 現在 出力モジュール
適用可能なプラットフォーム: GE Series 90-30, PACSystems RX3i
チャンネル: 8 single-ended outputs; each channel can be configured independently
📌 Configurable Output Ranges (Software Setup Only)
電圧: 0~10V (単極性), -10~+10V (バイポーラ)
現在: 0~20mA, 4~20mA (widely used for control valves and transmitters)
📐 Key Technical Specifications
解決: 15~16 bits, depending on selected range
Refresh Time: 8 ms for all 8 チャンネル
Maximum Load: 5 チャンネルあたりの電流
電源:
Backplane 5VDC (110ミリアンペア); external 24VDC user power (315ミリアンペア).
The 24VDC must be wired to terminal blocks; backplane power alone is insufficient.
診断: Open-wire fault detection for current mode, with fault alarm sent to the CPU.
Power-down Behavior: Configurable – hold last output value or reset to zero (only valid if external 24V stays powered).
正確さ: Factory-calibrated at ambient temperature; ±1%FS for current signals, ±3%FS for voltage signals under strong RF interference.
インストール: Fits any I/O slot; metal control cabinet mounting recommended.
⚠️ Version Notes
IC693ALG392A / B / C / D: Hardware revisions. Version C is the most widely stocked model, fully backward-compatible with existing programming and hardware configurations.
Comparison within the series: IC693ALG390 (2へ), IC693ALG391 (2へ). The ALG392 is the high-density 8-channel variant.
🔧 Typical Applications
Modulating control valves, VFD setpoints, proportional valves, 4–20mA actuators, signal retransmission to recorders (空調設備, 水処理, 化学工業, packaged machinery).
🛠️ Troubleshooting Common Failures
- Open-wire fault in current loop: Check terminal wiring, instrument power supply and loop resistance. The module does not supply loop power.
- Output drift: Stabilize the external 24VDC power supply, route wiring away from inverter high-power cables, and perform recalibration.
- No output change: Verify range configuration in GX Configurator, backplane power status, and online module status.
🔁 Alternative Replacements
同じプラットフォームのアップグレード: IC694ALG392 (RX3i high-performance version)
ブランド間の交換: Depends on PLC backplane; cannot be directly swapped with Allen-Bradley modules.
Application Scenarios for IC693ALG392C (GE 90-30 / RX3i 8-Channel AO Module)
コア機能: 8 independent 4~20mA / 0~10V / -10~+10V analog outputs to send setpoints to field actuators. This is a control-side output module; it only transmits control commands and does not collect field signals.
互換性のあるコントローラー: GE Fanuc Series 90-30, PACSystems RX3i. Mostly used for legacy project spares and retrofits of imported packaged equipment.
- 水処理 (最も一般的なアプリケーション)
- VFD setpoint: 4–20mA frequency command for water supply pumps, return pumps and chemical dosing pumps.
- Electric control valves: Regulate inlet valves, outlet valves, pH control valves and turbidity valves.
- Chemical dosing systems: Variable-speed metering pump flow setpoints for PAC/PAM, acid and alkali dosing.
- Aeration control: Adjust aeration duct dampers and fan vane opening for closed-loop DO (dissolved oxygen) コントロール.
- Sludge handling: Control sludge return valves and waste sludge valves.
- 空調設備 & Cleanroom Air Conditioning
- AHU air handlers: Modulate cold water valves, hot water valves and humidifier valves for constant temperature & 湿度管理.
- VAV variable-air-volume dampers for air handling units and exhaust cabinets.
- 冷却塔: Regulate cooling water valves and fan speed setpoints.
- 温度 & humidity closed-loop control for pharmaceutical cleanrooms.
- 化学薬品 & Fine Chemical Batching Systems
- 混合 & batching lines: Control feed valves and proportional valves to stabilize material ratios.
- Pressure control loops: Pneumatic diaphragm valves to maintain tank pressure.
- Temperature control loops: Steam and cooling water control valves for reactors.
- Small reaction vessels: VFD speed command for agitators, plus steam/cooling valve regulation.
アドバンテージ: High-density 8-channel design; multiple PID control loops can be centralized in one module to save I/O slots.
- 加熱 & Boiler Energy Systems
- Boiler controls: Gas regulating valves, feedwater valves, induced draft fan VFD setpoints.
- Heat exchanger stations: 主要な & secondary network regulating valves for heat exchanger temperature control.
- Waste heat recovery device modulation.
- プラスチック押出成形, 包装 & 一般機械
- 押出機: Proportional valve control and melt pump speed setpoints for barrel zone temperature control.
- コーティング & laminating machines: Tension proportional valves and line speed synchronization via VFD analog setpoints.
- Hydraulic proportional valve control (±10V signal preferred for pressure/flow continuous regulation).
- Multi-section speed synchronization for production lines.
- 粒 & フィード処理
- Grain drying lines: Hot air dampers and exhaust dampers for drying temperature closed-loop control.
- Continuous loss-in-weight feeding: VFD setpoints for feeding conveyors.
- その他の用途
Constant-pressure water supply pump control panels for buildings.
Exhaust gas treatment (RCO/RTO): Air damper adjustment and dilution fan speed setpoints.
Analog signal transmission to paperless recorders and digital indicators (0~10V signal).
✅ 選択 & 募集要項
- 4~20mA: Preferred for control valves, inverters and metering pumps. The module does not provide loop power; an external power supply is required to complete the current loop.
- ±10V: Used for hydraulic proportional valves and servo actuators.
- Designed for continuous closed-loop PID regulation; not suitable for discrete on/off signals.
- Primarily used for legacy equipment retrofits: Many older imported packaged machines use the 90-30 PLC; IC693ALG392C is the preferred spare part.
❌ 不適切な用途
Analog signal acquisition (use AI modules such as IC693ALG220 / ALG221 instead).
Direct driving of solenoid valves or high-power loads.
High-speed servo motion control (8ms full-channel refresh limits dynamic response).
Full List of GE Fanuc (エマーソン) Analog Output AO Modules
(Including mixed I/O modules with analog output channels)
Platform Classification: シリーズ 90-30 (IC693), RX3i Universal Backplane I/O (IC694), RX3i High-Performance PCI Backplane (IC695).
Suffix A/B/C/D = PCB hardware revisions; all versions are fully interchangeable with identical functions.
- シリーズ 90-30 (IC693, 廃止, スペアパーツのみ)
| モデル | チャンネル | タイプ | Ranges | 備考 |
| IC693ALG390 | 2へ | 電圧出力 | 0~10V / -10~+10V | Voltage-only, no current output |
| IC693ALG391 | 2へ | 電流出力 | 0~20mA, 4~20mA | Current-only |
| IC693ALG392 | 8へ | Universal Voltage/Current | 0~10V, ±10V, 0~20mA, 4~20mA | Single-ended; open-wire diagnosis; IC693ALG392C is the most common stock version |
| IC693ALG442 | 4AI+2AO | Mixed Analog I/O | 0~10V, ±10V, 0~20mA, 4~20mA | 4 differential inputs + 2 へ; compatible with 90‑30 & RX3i |
- RX3i IC694 Series (Backward Compatible with 90-30, Direct Upgrade Replacement)
| モデル | チャンネル | タイプ | Ranges | 備考 |
| IC694ALG390 | 2へ | 電圧出力 | 0~10V, ±10V | Upgrade version of IC693ALG390 |
| IC694ALG391 | 2へ | 電流出力 | 0~20mA, 4~20mA | Upgrade version of IC693ALG391 |
| IC694ALG392 | 8へ | Universal Voltage/Current | 0~10V, ±10V, 0~20mA, 4~20mA | Direct replacement for IC693ALG392; 8ms refresh |
| IC694ALG442 | 4AI+2AO | Mixed Analog I/O | 0~10V, ±10V, 0~20mA, 4~20mA | 2ms high-speed refresh |
| IC694ALG542 | 4AI+2AO | Mixed Analog I/O | 0~10V, ±10V, 0~20mA, 4~20mA | より高い精度; ホットスワップ対応 |
- RX3i IC695 Series (High-Performance PCI Backplane, New Project Standard)
| モデル | チャンネル | タイプ | Ranges | 備考 |
| IC695ALG704 | 4へ | Universal Voltage/Current | 0~10V, ±10V, 0~20mA, 4~20mA | With upper/lower limit alarm, ランプ & slew rate limiting |
| IC695ALG708 | 8へ | Universal Voltage/Current | 0~10V, ±10V, 0~20mA, 4~20mA | High-density 8-channel; no HART support |
| IC695ALG728 | 8へ | Universal AO + ハート | 0~10V, ±10V, 0~20mA, 4~20mA | HART protocol supported, ideal for smart control valves |
| IC695ALG808 | 8へ | Channel-Isolated AO | 0~10V, ±10V, 0~20mA, 4~20mA | Channel-to-channel galvanic isolation; high anti-interference for chemical and hazardous cabinet applications |
- 補足事項
- All IC693 series modules are discontinued; 余剰在庫のみ, refurbished and used units are available. New projects should select IC694 or IC695 series.
- セレクションガイド:
Standard valves & VFD setpoints: IC693ALG392 / IC694ALG392 / IC695ALG708
Smart HART valves: IC695ALG728
High EMI & ground potential difference: IC695ALG808 (isolated channels)
Few analog points & compact cabinets: ALG390/391, IC695ALG704
Combined AI+AO to save slots: ALG442 / ALG542
- Common Power Requirement for all AO modules:
Backplane 5VDC only supplies logic power. An external 24VDC field power supply is mandatory. Current loops require external power to complete the circuit; the module cannot supply loop current.
- VersaMax Micro System (IC200) AO Modules (Reference Only)
IC200ALG320: 4-channel 4~20mA current output
IC200ALG321: 4-channel universal voltage/current output
コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ



















NH42-63-318x560.png)



