シュナイダー BMXDDI3202KH デジタル入力モジュール - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

微信: +86-13184948252 ワッツアップ: 0086-13811255435 電子メール: kent@bestcontactor.com

について 接触 |

シュナイダー BMXDDI3202KH デジタル入力モジュール - コンタクタ,サーキットブレーカー,センサー,エンコーダ,PLC,コンバータ

PLC/

シュナイダー BMXDDI3202KH デジタル入力モジュール

シリーズ: Modicon X80 (M340 PLC) Model explanation: BMXDDI3202KH = BMXDDI3202K + H; H = Conformal Coating version for harsh environments. Electrical specifications are identical to BMXDDI3202K. Only the PCB is coated with conformal coating for moisture-proof, mould-proof and salt-spray resistance, suitable for ports, 化学プラント, underground sites, high-humidity and dusty conditions. ✅ Basic Specifications Type: ...

  • 製品詳細

シリーズ: Modicon X80 (M340 PLC)

Model explanation: BMXDDI3202KH = BMXDDI3202K + H; H = Conformal Coating version for harsh environments. Electrical specifications are identical to BMXDDI3202K. Only the PCB is coated with conformal coating for moisture-proof, mould-proof and salt-spray resistance, suitable for ports, 化学プラント, underground sites, high-humidity and dusty conditions.

✅ 基本仕様

タイプ: 32-channel isolated digital 入力モジュール, シンク (正論理)

入力電圧: 24VDC, sensor supply range 19~30VDC

Input current per channel: 2.5mA @24V

論理 1: ≥11V / ≥2mA; 論理 0: ≤5V / ≤0.5mA

入力インピーダンス: 9600おお

応答時間: Typical 4ms, maximum 7ms

分離: Channel-to-channel isolation, 絶縁抵抗 >10MΩ at 500VDC

配線: Compatible with 2-wire / 3-wire proximity switches (IEC61131-2 Type3, IEC60947-5-2). Input parallel connection is not allowed

コネクタ: Single 40-pin FCN interface, single slot, hot-swap supported

消費電力: ≤3.9W; Typical backplane 3.3V consumption 121mA

Enclosure protection: IP20

📌 Matching Cables (40-pin FCN)

  1. BMXFCWxxx3: Pre-wired loose cables (3m/5m/10m: BMXFCW303 / BMXFCW503 / BMXFCW1003)
  2. BMXFCCxxx3: Pre-assembled HE10 terminal cables (0.5/1/2/3/5/10メートル)

🧩 Compatible CPUs

Full Modicon M340 series: BMXP34xx00, BMXP34xx20 (including H versions). General X80 rack, configured via Unity Pro software.

⚖️ Model Comparison

BMXDDI3202K: 標準バージョン, no conformal coating, for conventional control cabinets

BMXDDI3202KH: Conformal coated version for harsh environments. Fully interchangeable in program, pinout and cabling.

📎 Alternative Selection Reference

Same-platform replacement: No drop-in equivalent. For fewer points, refer to BMXDDI1602K(H) (16-point Sink DI).

国内での交換: Verify sink logic, isolation and filter time, suitable for domestic PLC remote IO modules.

⚠️ Troubleshooting Tips

  1. 入力信号がありません: Check 24V supply, sensor polarity (シンク, signal connects to 0V), broken pins in prefabricated cables.
  2. 点滅 / 誤ったトリガー: Check voltage drop and shielding. This module uses fixed hardware filter; filter parameters cannot be modified by software.
  3. Prefer KH version for humid and corrosive environments; standard K version is prone to PCB corrosion under long-term high humidity.

シュナイダー デジタル入力 (から) Module List by Platform

注記: Suffix H = Conformal coating for harsh environments. X80 platform compatible with M340 / M580; Sink = sinking input, Source = sourcing input; AC = AC input.

  1. Modicon X80 (BMX series, M340 / M580)

DC Digital Input (BMXDDI)

モデルポイント説明
BMXDDI1602K / BMXDDI1602KH1624VDC, シンク
BMXDDI1603K / BMXDDI1603KH1648VDC, シンク
BMXDDI1604T16125VDC, シンク, 幅広い温度
BMXDDI3202K / BMXDDI3202KH3224VDC, シンク (the model you enquired)
BMXDDI3203K / BMXDDI3203KH3248VDC, シンク
BMXDDI3232K / BMXDDI3232KH3212/24VDC, Sink/Source configurable
BMXDDI6402K / BMXDDI6402KH6424VDC, シンク

AC Digital Input (BMXDAI)

モデルポイント説明
BMXDAI08058220VAC
BMXDAI08148100~120VAC
BMXDAI16021624VAC/24VDC, ソース
BMXDAI16031648VAC
BMXDAI160416100~120VAC
BMXDAI161416220VAC

X80 Safety DI (Safety PLC dedicated)

モデルポイント説明
BMXSDI160216Safety digital input, 24VDC
  1. TM3シリーズ (Expansion for M221/M241/M251/M262 Compact PLC)
モデルポイント説明
TM3DI8824VDC, ネジ端子
TM3DI8G824VDC, spring clamp terminals
TM3DI8A8120VAC
TM3DI161624VDC, ネジ端子
TM3DI16G1624VDC, spring clamp terminals
TM3DI16K1624VDC, HE10 connector
TM3DI32K3224VDC, HE10 connector
  1. Advantys STB Distributed Remote IO
モデルポイント説明
STBDDI37251624VDC Sink
STBDDI3420824VDC Sink
STBDDI3610424VDC Sink
STBDAI02002100~240VAC
STBDAI04004100~240VAC
  1. 補足事項
  2. X80 naming rule: `BMXDDI` = DC DI; `BMXDAI` = AC DI; `K` standard, `KH` conformal coated.
  3. K and KH variants of the same model are fully interchangeable in pinout, programming and backplane interface, only differing in PCB protection.
  4. Mixed I/O modules (ディ+ドゥ) such as BMXDDM16022 are excluded from this table.

Application Scenarios of Schneider Digital Input (から) Modules (X80/STB/TM3, 等)

Core function of DI modules: Collect binary switch signals, transfer ON/OFF status from external dry contacts, センサー, 押しボタン, limit switches and auxiliary contacts of contactors to PLC. It only detects on/off status and does not process analog signals. The following is sorted by industry and signal type, applicable to BMXDDI3202KH and other X80 modules.

  1. General Signal Acquisition (Used across all industries)
  2. Pushbuttons, selector switches, 非常停止ボタン

Local cabinet operation, remote control boxes, E-stop signals (general E-stop; safety E-stop should use dedicated safety DI module BMXSDI1602).

  1. Limit switches, トラベルスイッチ, 近接スイッチ, 光電センサー

Equipment position detection: cylinder confirmation, ドアスイッチ, baffle limit for material level, 物体存在検出.

BMXDDI3202KH is 24VDC Sink, compatible with mainstream NPN proximity switches.

  1. Auxiliary contacts of contactors / リレー, circuit breaker status feedback

Motor running feedback, VFD ready feedback, circuit breaker open/close status, thermal relay fault signals.

  1. Dry contact signals

Fire alarm systems, アクセス制御, damper/valve position feedback in HVAC, float level switches.

  1. 空調設備

ランニング / fault feedback of fans and water pumps

Differential pressure switches, frost protection switches, air damper / water valve end-position feedback

Filter differential pressure alarm, high/low float level switches

Feedback of smoke exhaust dampers and fire dampers

Conformal coated KH versions (BMXDDIxxxxKH) are preferred for humid and dusty machine rooms.

  1. 水処理, 給水 & 排水, Wastewater Plants

Level switches (high level, low level, overflow)

Pump run, 故障, hand-auto status

Limit signals for bar screens and sludge scrapers

Pulse signals from flow meters (high-speed pulses require dedicated high-speed counter modules; standard DI is not suitable for high-frequency pulses)

Valve open / closed position feedback

KH coated modules are widely used in corrosive, high-humidity wastewater sites.

  1. 包装, 組立ライン & 自動生産ライン

Photoelectric detection for material presence / missing material

Cylinder and clamp confirmation signals

Conveyor belt jam and deviation switches

Barcode detection, silo level switches

Safety gate and guard door status signals

BMXDDI6402K (64-point DI) is commonly used for high-point-count lines to save slots.

  1. Crane Systems, 運ぶ & Warehouse Logistics

Crane travel limits, upper/lower hard limits, buffer switches

Pallet in-position, bay detection

Roller conveyor deviation and E-stop loop feedback

Roller shutter and guard door status

  1. Power Distribution Rooms & Energy Monitoring

Circuit breaker and disconnector open/close position feedback for high-voltage cabinets

Cabinet door interlock, earthing switch status

Transformer thermostat switches, cooling fan feedback

DC panel fault alarm dry contacts

BMXDAI AC DI modules are often used for 220VAC cabinet signals.

  1. 油 & ガス, 化学工業, ポート (過酷な環境)

Valve position feedback, pump status, dry contact output of combustible gas detectors

Limit switches and door interlocks for trestle and quay equipment

Salt spray, high humidity and condensation → select KH conformal coated versions (BMXDDI3202KH etc.). Standard K versions are vulnerable to corrosion.

  1. ビルディングオートメーション, 防火 & Pumping Stations

Dry contact alarms from fire host, sprinkler pressure switches

Elevator interlock signals, smoke exhaust fan status

Rainwater pumps, sump tank level monitoring

✅ Quick Selection Guide by Scenario

Normal indoor control cabinet, 乾燥した環境: BMXDDIxxxK

化学薬品 / ポート / 高湿度 & 塩水噴霧: BMXDDIxxxKH (コンフォーマルコーティング)

220VAC contact signals: BMXDAI AC DI

安全回路, 安全ゲート, safety E-stop: BMXSDI safety DI

小型機械, low I/O count: TM3DI series

Distributed remote IO with scattered field points: STB Advantys remote DI

⚠️ Scope Limitations (What DI modules cannot do)

  1. Cannot directly measure 4-20mA or temperature (AI analog modules required)
  2. Standard DI is not suitable for high-frequency pulse counting (high-speed counter module required)
  3. Safety functions shall not be implemented via ordinary DI; dedicated safety DI modules are mandatory.

前へ:

次:

返信を残す

伝言を残す