Mitutoyo HH-336 Hardness Tester

Model No.: 811-336-10 (HH-336-01 is the equivalent variant)

시리즈: HARDMATIC HH-300 (811 시리즈)

유형: Compact Digital Shore A Durometer

기본사양

규모: Shore A

형태: 컴팩트한 사이즈, 디지털 디스플레이

Indenter: 35° truncated cone, tip diameter φ0.79 mm, shank φ1.25 mm

Indenter projection: 2.5 mm

Applicable materials: General rubber, elastomers, soft PVC, soft plastics, leather, neoprene and other soft materials

전원공급장치: SR44 silver oxide button cell

전체 치수: 59×40×147 mm

무게: 290 g

기능: Peak hold, data lock, Digimatic output for MeasurLink data collection

옵션 액세서리

Test stand for calibration: CTS-103 (주문 번호. 811-013), exclusively for HH-335 / HH-336

Shore A calibration test blocks, data cable

시리즈 선택 가이드

HH-330: Compact digital Shore E (거품, ultra-soft rubber)

HH-332: Long-handle digital Shore A (grooves, 깊은 충치)

HH-334: Long-handle digital Shore D (hard rubber & rigid plastics)

HH-336: Compact digital Shore A (이 모델)

HH-338: Compact digital Shore D

추가 참고사항

규정 준수 표준: ISO 7619, ASTM D2240

Compact model: for flat open specimens; long-handle model: for narrow recessed areas

대안: Domestic digital Shore A durometers can be used for comparison, but indent geometry and metrology systems differ. 원래의 Mitutoyo is preferred for export quality control.

Mitutoyo HH-336 (811-336-10 Digital Shore A Durometer)

기준: ASTM D2240 / ISO 7619; with peak hold & Digimatic data output; battery: SR44

Full Operating Procedures (휴대용 & CTS-103 Stand Mount)

Pre-Test Preparation

청소: Wipe the pressure foot, indenter and specimen surface free of oil, dust and debris. Never strike the indenter.
Specimen requirements: Rubber/elastomer thickness ≥6 mm; measuring points ≥12 mm from edges; spacing between points ≥6 mm; place specimen on a rigid flat plate without soft backing.
전원 켜짐: Short press the power key. With no load on the indenter, the reading shall be 0.0 하아; perform zero reset if offset.
모드 선택: Use Peak Hold to lock the maximum reading automatically; real-time reading mode is also available.

Stand mounting (CTS-103): Fix the durometer vertically and apply load by dead weight to eliminate manual pressure variation, recommended for outgoing inspection and metrology comparison.

Handheld Measurement Steps

Keep the durometer perpendicular to the specimen surface; no tilting.
Press down smoothly until the entire pressure foot fully contacts the specimen (do not only push the indenter); complete the action within 1 두번째.
Peak mode: The display locks the peak hardness value; record the reading and release to let the indenter rebound to zero.
Take at least 5 readings per sample, discard outliers and calculate the average; increase point spacing to 15 mm for soft foams.
Power off after use; remove the battery for long-term storage.

CTS-103 Stand Operation (QC Preferred)

Clamp the HH-336 firmly and adjust vertical alignment; clean the worktable.
Place the specimen at the table center.
Turn the crank to lift the worktable slowly until the pressure foot fully seats on the specimen, then record the reading.
Lower the table and repeat on new test points.

Important prohibition: Do not hold continuous pressure on the sample; soft rubber will creep and cause low readings.

구경 측정 & 검증 방법 (Daily Check, Block Verification, Annual Metrology)

⚠️ The internal spring and indenter geometry are not user-adjustable. If out of tolerance, send the unit to Mitutoyo or an accredited lab for repair. The following are only verification steps, not hardware adjustment.

Daily Zero Check (Every Power-On)
Suspend the unit with no force on the indenter; power on and press ZERO to set the display to 0.0.
Press firmly against a flat optical glass plate until the indenter retracts fully. The reading shall be approximately 100 하아 (tolerance ±1 HA).

If not reaching 100 하아: Clean the indenter gap with alcohol, repeat pressing 3–5 times. If still abnormal, stop use and submit for inspection.

Verification with Standard Hardness Blocks (일일 / Batch Change)
Use certified Shore A calibration blocks covering low, medium and high ranges (예를 들어, 30에이, 60에이, 80에이).
Zero first, then press vertically onto the block with full foot contact, record the peak reading and compare with the block nominal value.
Pass criterion: Error ≤ ±1 HA. If exceeded, discontinue use and send for calibration.

Recommended cycle:

작업장: Daily verification

External calibration: Once per year (CNAS certificate)

After dropping or indenter impact: Immediately stop use and re-calibrate.

Full Calibration Items by Metrology Lab

영점 & full-scale (100 HA on glass) indication error

Indenter projection length: 2.5 mm nominal

Indenter geometry: 35° cone, tip diameter φ0.79 mm

Spring test force verification

III. 문제 해결

잘못	근본 원인	치료
디스플레이 없음 / 검은 화면	Dead SR44 battery, 역극성, 산화된 접점	Replace SR44 cell; clean spring contacts; 극성을 확인하세요
0으로 설정할 수 없습니다. / zero drift	Sticking indenter, rubber/dust trapped in gap, 봄의 피로, faulty zero key	Clean indenter gap with alcohol cotton swabs; do not apply oil; re-test after cleaning; persistent drift → send for repair
Unstable readings, large variation between repeated tests	1. Tilting instrument; 2. Thin/soft specimen with bottom compression; 3. Incomplete foot contact; 4. Material creep; 5. Worn indenter	Measure vertically; thicken sample or use rigid backing plate; ensure full foot contact; shorten dwell time; inspect indenter tip for chipping
Low readings, cannot reach high values	Chipped/worn indenter tip, weakened spring, stuck indenter	Visually inspect indenter; 깨끗한; if no improvement, replace indenter/spring assembly at service center
Reading far below 100 HA on glass	Foreign matter jamming indenter, deformed pressure foot, internal mechanical damage	Clean thoroughly; never strike the unit; if unresolved, send to metrology service (no user spring adjustment)
Hold function fails / keys unresponsive	Moisture ingress, aged switches, temporary program glitch	전원 끄기, remove battery and rest 5 minutes before reinstallation; keep unit dry; do not rinse with water
No Digimatic output	Mismatched cable, dirty port, incorrect MeasurLink settings	Use genuine Mitutoyo Digimatic cable; clean connector pins; verify software communication parameters
Err error code on screen	Overrange or mechanical jamming	Release the indenter, zero and restart; repeated errors indicate internal failure – send for service

유지 & 지침
Never drop or strike the indenter; the hard metal tip will be damaged permanently after impact.
Only clean with anhydrous ethanol and soft cotton swabs. Do not use oil or WD40, which will trap debris and cause sticking.
Avoid prolonged sustained compression to prevent spring fatigue.
저장: Keep dry at ambient temperature, 직사광선을 피해서, ozone and high heat. Remove the battery during long-term storage to prevent leakage.
Scale distinction: HH-336 = Shore A. Use HH-338 (Shore D) for rigid plastics; Shore A readings are invalid on hard materials.

Full Model List of Mitutoyo Hardness Testers (By Category)

메모: HH-300 (811 시리즈) = HARDMATIC Shore Durometers; HH-411/HH-V400 = Rebound Leeb testers; HR = Rockwell; HV = Vickers; HM = Micro-Vickers; 접미사 -01 denotes equivalent variants. Stands are listed separately.

HH-300 Series Shore Durometers (811 Series for Rubber / 거품 / 플라스틱, including HH-336)

모델	주문 번호.	표시하다	애플리케이션
HH-329	811-329-10	Analog dial	거품, ultra-soft rubber, 펠트, 스펀지
HH-330	811-330-10	디지털	거품, soft sponge, deep recesses
HH-331	811-331-10	Analog dial	General rubber, soft PVC
HH-332	811-332-10	디지털	고무, soft plastic, narrow grooves
HH-333	811-333-10	Analog dial	Hard rubber, rigid plastic, bakelite
HH-334	811-334-10	디지털	Epoxy, 단단한 플라스틱, hard rubber
HH-335	811-335-10	Analog dial	Elastomers, general rubber
HH-336	811-336-10	디지털	General rubber & soft plastic (현재 모델)
HH-337	811-337-10	Analog dial	Hard rubber, rigid plastic
HH-338	811-338-10	디지털	Hard plastic, rigid rubber