성명: GX-series EtherCAT IO-Link Master Unit (IP67 Field Type)
코어 포지셔닝: EtherCAT 버스, 8-channel IO-Link master, M12 A-coding female connector. 방진 및 방수, can be mounted directly on equipment frames or production lines without installation inside control cabinets.
✅ 주요 사양
Number of ports: 8 IO-Link ports (M12 A-coding female)
Bus interface: EtherCAT (IN/OUT M12, supports daisy-chain connection)
IO-Link version: V1.1.2
전송 속도: COM1 (4.8케이) / COM2 (38.4케이) / COM3 (230.4케이) 자동 적응
Power supply per port: DC24V, 최대. 200mA per port, with independent short-circuit protection
SIO compatible mode: Switchable to PNP DI / PNP DO
에서: ON ≥15V, OFF ≤5V; multi-stage filter time optional (공장 기본값: 1ms)
~하다: Push-pull output, 0.3채널당 A
전원 공급 범위: DC20.4~26.4V (24V ±10%/-15%)
보호 등급: IP67 (suitable for dusty and humid field environments)
구성 소프트웨어: 시스맥 스튜디오, CX-ConfiguratorFDT
호환 PLC: NX/NJ/NY series EtherCAT controllers
✅ Main Features
- IP67 field mounting, saves junction boxes, adopts M12 Smartclick quick connectors
- 8 independent IO-Link master ports. Each port can connect IO-Link sensors, 밸브 아일랜드, 아날로그 모듈, RFID and other smart slaves
- Flexible port mode switching: IO-Link smart mode / SIO digital DI / SIO digital DO
- EtherCAT daisy-chain, simple networking. Diagnostic information (sensor temperature, signal quality, event alarms) can be uploaded to PLC
- Supports automatic upload, download and backup of IO-Link device parameters. No manual setting required after sensor replacement
✅ Similar Series & 대체 참조
GX-ILM04C: 4-port version (same architecture IP67 EtherCAT IO-Link master)
NX-ILM08C: NX backplane type (캐비닛 장착형, non-IP67), 혼동하지 마십시오
✅ 일반적인 적용 시나리오
조립 라인, 포장 기계, 공작기계, material handling lines, for mass connection of IO-Link photoelectric sensors, 근접 센서, 압력 센서, flow sensors, proportional valves and IO-Link hubs.
✅ Notes
EtherCAT cables shall be CAT5e or higher grade shielded STP cable;
SIO DO is PNP push-pull output, cannot directly drive heavy loads;
All ports share 24V power supply, with independent short-circuit protection for each port.
GX‑ILM08C’s core advantages: IP67 field-side installation, EtherCAT daisy-chain, 8-channel IO‑Link, ports compatible with ordinary DI/DO. It is designed for outside control cabinets, dusty and humid production lines, and differentiated from NX‑ILM08C (IP20 for cabinet installation).
- 일반적인 산업 응용 분야
- Automotive component assembly lines, 공구 설비, 로봇 워크스테이션
Connected to IO-Link proximity sensors, 광전 센서, cylinder magnetic switches, 압력 센서, proportional valves, fixture in-place sensors.
장점: Modules can be mounted beside tooling without routing cables back to cabinet junction boxes; sensor temperature, signal margin and offset data can be read for predictive maintenance. Parameters can be downloaded automatically during fixture changeover to shorten product change time.
- 포장 기계 (흐름 포장지, case packers, 팔레타이저)
For photoelectric detection, 물질적 수준, 압력, web guiding sensors and IO-Link valve islands. IP67 rating fits oily and humid conditions. Ordinary PNP sensors can be used in SIO mode, friendly for retrofitting projects mixing old and new sensors.
- Material handling lines, 라인 정렬, 자동화 창고, AGV stations
위치 감지, code-reading trigger and photoelectric sensors for belt conveyors, roller lines and transfer units. Long-distance segmented EtherCAT daisy-chain wiring. 단선, short circuit and sensor disconnection alarms are sent to PLC for fast fault location and reduced downtime.
- 공작기계, stamping and injection molding equipment
Peripheral detection of machine tools, 안전 라이트 커튼, mold confirmation, mold pressure, cooling circuit flow and temperature. Resists cutting fluid and dust. Sensor degradation data can be collected for early warning to avoid defective batches.
- 음식 & pharmaceutical production lines (wash-down environments)
IP67 protection and M12 quick connectors for wash applications. Connected to sanitary IO-Link flow, temperature and level sensors. Supports sensor ID verification to prevent wrong installation.
- 리튬 배터리 & photovoltaic equipment (liquid injection, lamination, 정렬)
Centralized access of large numbers of small-point smart sensors. Sensor parameters can be backed up and restored with one click; no on-site commissioning required when replacing sensors in batches. Status data can be uploaded to SCADA for OEE analysis.
- Functional Use Cases
감지기 condition visualization & 예측 유지 관리: Monitor photoelectric received light intensity, sensor temperature, vibration and pressure, set threshold alarms before total failure.
Production line retrofitting: Expand I/O points locally on site without adding new control cabinets. Legacy sensors use SIO DI/DO while new smart sensors run IO-Link.
Flexible multi-product production lines: Automatic parameter download for product changeover, automatic sensor identification and anti-mismatch function.
Distributed I/O architecture: Multiple scattered acquisition points on one line connected via EtherCAT chain, reducing heavy multi-core cables.
III. 부적합한 시나리오
Cabinet internal installation with compact backplane requirement: choose NX‑ILM08C
High corrosion or continuous immersion conditions (only IP67, not for long-term submersion)
High-current loads per channel (최대. 0.3A for DO ports)
- Matching Configuration
제어 장치: NX/NJ/NY series EtherCAT PLC; 소프트웨어: 시스맥 스튜디오; 네트워킹: Multiple GX modules daisy-chained with STP shielded EtherCAT cables.
오므론 GX-series IO-Link Master Units
✅ GX series only has one official IO-Link master model: GX-ILM08C. GX-ILM04C does not exist; the 4-port field IO-Link master does not belong to the GX series.
| 모델 | 포트 | 보호 | 버스 | 인터페이스 | 설명 |
| GX-ILM08C | 8 IO-링크 | IP67 | EtherCAT | M12 A-coding female (IO-링크); M12 D-coding (EtherCAT IN/OUT) | Field distributed I/O, M12 quick connect, port switchable SIO DI/DO, compatible with NX/NJ/NY EtherCAT controllers |
Confusable IO-Link Masters from Related Families (Not GX series)
| 모델 | 시리즈 | 포트 | 보호 | 버스 | 건설 |
| NX-ILM400 | NX | 4 | IP20 | EtherCAT | Cabinet backplane mounting, 나사식 터미널, for indoor cabinet use |
| NXR-ILM08C-ECT | NXR | 8 | IP67 | EtherCAT | Rugged remote terminal, similar form factor to GX |
| NXR-ILM08C-EIT | NXR | 8 | IP67 | 이더넷/IP | EtherNet/IP version, not EtherCAT |
Additional GX-series EtherCAT Remote I/O Modules (Not IO-Link Masters)
GX is Omron’s large IP67 EtherCAT remote I/O family. Besides IO-Link master, it includes digital and analog modules:
GX-ID16□2 / OD16□2 / MD16□2: 3-tier terminal digital I/O
GX-□D16□1 / OC1601: 2-tier terminal digital I/O
GX-□D16□8 / □D32□8: e-CON connector digital I/O
GX-AD0471 / DA0271: 아날로그 입력 / 아날로그 출력
GX-EC0211 / EC0241: EtherCAT junction / branch units
GX-JC03 / JC06: Extension connectors
접촉기,회로 차단기,감지기,인코더,PLC,변환기





















NH42-63-318x560.png)



