Schneider BMXDDI3202KH Digital Input Module - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

위챗: +86-13184948252 왓츠앱: 0086-13811255435 이메일: kent@bestcontactor.com

에 대한 연락하다 |

Schneider BMXDDI3202KH Digital Input Module - 접촉기,회로 차단기,감지기,인코더,PLC,변환기

PLC/

Schneider BMXDDI3202KH Digital Input Module

시리즈: Modicon X80 (M340 PLC) 모델 설명: BMXDDI3202KH = BMXDDI3202K + 시간; H = Conformal Coating version for harsh environments. Electrical specifications are identical to BMXDDI3202K. Only the PCB is coated with conformal coating for moisture-proof, mould-proof and salt-spray resistance, suitable for ports, 화학공장, underground sites, high-humidity and dusty conditions. ✅ Basic Specifications Type: ...

  • 제품 세부정보

시리즈: Modicon X80 (M340 PLC)

모델 설명: BMXDDI3202KH = BMXDDI3202K + 시간; H = Conformal Coating version for harsh environments. Electrical specifications are identical to BMXDDI3202K. Only the PCB is coated with conformal coating for moisture-proof, mould-proof and salt-spray resistance, suitable for ports, 화학공장, underground sites, high-humidity and dusty conditions.

✅ 기본사양

유형: 32-channel isolated digital 입력 모듈, 싱크대 (positive logic)

입력 전압: 24VDC, sensor supply range 19~30VDC

Input current per channel: 2.5mA @24V

논리 1: ≥11V / ≥2mA; 논리 0: 5V 이하 / ≤0.5mA

입력 임피던스: 9600오

응답 시간: Typical 4ms, maximum 7ms

격리: Channel-to-channel isolation, 절연저항 >10MΩ at 500VDC

배선: 2선식과 호환 가능 / 3-wire proximity switches (IEC61131-2 Type3, IEC60947-5-2). Input parallel connection is not allowed

커넥터: Single 40-pin FCN interface, single slot, hot-swap supported

소비전력: ≤3.9W; Typical backplane 3.3V consumption 121mA

Enclosure protection: IP20

📌 Matching Cables (40-pin FCN)

  1. BMXFCWxxx3: Pre-wired loose cables (3m/5m/10m: BMXFCW303 / BMXFCW503 / BMXFCW1003)
  2. BMXFCCxxx3: Pre-assembled HE10 terminal cables (0.5/1/2/3/5/10중)

🧩 Compatible CPUs

Full Modicon M340 series: BMXP34xx00, BMXP34xx20 (including H versions). General X80 rack, configured via Unity Pro software.

⚖️ Model Comparison

BMXDDI3202K: 표준 버전, 컨포멀 코팅 없음, for conventional control cabinets

BMXDDI3202KH: Conformal coated version for harsh environments. Fully interchangeable in program, pinout and cabling.

📎 대체 선택 참조

Same-platform replacement: No drop-in equivalent. For fewer points, refer to BMXDDI1602K(시간) (16-point Sink DI).

국내 대체: Verify sink logic, isolation and filter time, suitable for domestic PLC remote IO modules.

⚠️ Troubleshooting Tips

  1. No input signal: Check 24V supply, sensor polarity (싱크대, signal connects to 0V), broken pins in prefabricated cables.
  2. 섬광 / 거짓 트리거링: Check voltage drop and shielding. This module uses fixed hardware filter; filter parameters cannot be modified by software.
  3. Prefer KH version for humid and corrosive environments; standard K version is prone to PCB corrosion under long-term high humidity.

슈나이더 디지털 입력 (에서) Module List by Platform

메모: Suffix H = Conformal coating for harsh environments. X80 platform compatible with M340 / M580; Sink = sinking input, Source = sourcing input; AC = AC input.

  1. Modicon X80 (BMX series, M340 / M580)

DC Digital Input (BMXDDI)

모델전철기설명
BMXDDI1602K / BMXDDI1602KH1624VDC, 싱크대
BMXDDI1603K / BMXDDI1603KH1648VDC, 싱크대
BMXDDI1604T16125VDC, 싱크대, 넓은 온도
BMXDDI3202K / BMXDDI3202KH3224VDC, 싱크대 (the model you enquired)
BMXDDI3203K / BMXDDI3203KH3248VDC, 싱크대
BMXDDI3232K / BMXDDI3232KH3212/24VDC, Sink/Source configurable
BMXDDI6402K / BMXDDI6402KH6424VDC, 싱크대

AC Digital Input (BMXDAI)

모델전철기설명
BMXDAI08058220VAC
BMXDAI08148100~120VAC
BMXDAI16021624VAC/24VDC, 원천
BMXDAI16031648VAC
BMXDAI160416100~120VAC
BMXDAI161416220VAC

X80 Safety DI (Safety PLC dedicated)

모델전철기설명
BMXSDI160216Safety digital input, 24VDC
  1. TM3 시리즈 (Expansion for M221/M241/M251/M262 Compact PLC)
모델전철기설명
TM3DI8824VDC, 나사 터미널
TM3DI8G824VDC, spring clamp terminals
TM3DI8A8120VAC
TM3DI161624VDC, 나사 터미널
TM3DI16G1624VDC, spring clamp terminals
TM3DI16K1624VDC, HE10 connector
TM3DI32K3224VDC, HE10 connector
  1. Advantys STB Distributed Remote IO
모델전철기설명
STBDDI37251624VDC Sink
STBDDI3420824VDC Sink
STBDDI3610424VDC Sink
STBDAI02002100~240VAC
STBDAI04004100~240VAC
  1. 보충 노트
  2. X80 naming rule: `BMXDDI` = DC DI; `BMXDAI` = AC DI; `K` standard, `KH` conformal coated.
  3. K and KH variants of the same model are fully interchangeable in pinout, programming and backplane interface, only differing in PCB protection.
  4. Mixed I/O modules (DI+DO) such as BMXDDM16022 are excluded from this table.

Application Scenarios of Schneider Digital Input (에서) 모듈 (X80/STB/TM3, 등.)

Core function of DI modules: Collect binary switch signals, transfer ON/OFF status from external dry contacts, 센서, 푸시버튼, limit switches and auxiliary contacts of contactors to PLC. It only detects on/off status and does not process analog signals. The following is sorted by industry and signal type, applicable to BMXDDI3202KH and other X80 modules.

  1. General Signal Acquisition (Used across all industries)
  2. 푸시버튼, 선택기 스위치, 비상 정지 버튼

Local cabinet operation, remote control boxes, E-stop signals (general E-stop; safety E-stop should use dedicated safety DI module BMXSDI1602).

  1. 리미트 스위치, 여행 스위치, 근접 스위치, 광전 센서

Equipment position detection: cylinder confirmation, 도어 스위치, baffle limit for material level, 물체 존재 감지.

BMXDDI3202KH is 24VDC Sink, compatible with mainstream NPN proximity switches.

  1. Auxiliary contacts of contactors / 릴레이, circuit breaker status feedback

Motor running feedback, VFD ready feedback, circuit breaker open/close status, thermal relay fault signals.

  1. Dry contact signals

Fire alarm systems, 접근 제어, damper/valve position feedback in HVAC, float level switches.

  1. 공조

달리기 / fault feedback of fans and water pumps

Differential pressure switches, frost protection switches, air damper / water valve end-position feedback

필터 차압 경보, high/low float level switches

Feedback of smoke exhaust dampers and fire dampers

Conformal coated KH versions (BMXDDIxxxxKH) are preferred for humid and dusty machine rooms.

  1. 수처리, 상수도 & 배수, 폐수 처리장

Level switches (높은 수준, low level, overflow)

Pump run, 잘못, hand-auto status

Limit signals for bar screens and sludge scrapers

Pulse signals from flow meters (high-speed pulses require dedicated high-speed counter modules; standard DI is not suitable for high-frequency pulses)

밸브 열림 / 폐쇄 위치 피드백

KH coated modules are widely used in corrosive, high-humidity wastewater sites.

  1. 포장, 조립 라인 & 자동화된 생산 라인

Photoelectric detection for material presence / missing material

Cylinder and clamp confirmation signals

Conveyor belt jam and deviation switches

Barcode detection, silo level switches

Safety gate and guard door status signals

BMXDDI6402K (64-point DI) is commonly used for high-point-count lines to save slots.

  1. Crane Systems, 운반 & Warehouse Logistics

Crane travel limits, upper/lower hard limits, buffer switches

팔레트 정위치, bay detection

Roller conveyor deviation and E-stop loop feedback

Roller shutter and guard door status

  1. Power Distribution Rooms & 에너지 모니터링

Circuit breaker and disconnector open/close position feedback for high-voltage cabinets

캐비닛 도어 인터록, earthing switch status

Transformer thermostat switches, cooling fan feedback

DC panel fault alarm dry contacts

BMXDAI AC DI modules are often used for 220VAC cabinet signals.

  1. 기름 & 가스, 화학 산업, 포트 (가혹한 환경)

Valve position feedback, pump status, dry contact output of combustible gas detectors

Limit switches and door interlocks for trestle and quay equipment

Salt spray, high humidity and condensation → select KH conformal coated versions (BMXDDI3202KH etc.). Standard K versions are vulnerable to corrosion.

  1. 빌딩 자동화, 화재 예방 & 펌핑 스테이션

Dry contact alarms from fire host, sprinkler pressure switches

Elevator interlock signals, smoke exhaust fan status

Rainwater pumps, sump tank level monitoring

✅ Quick Selection Guide by Scenario

Normal indoor control cabinet, 건조한 환경: BMXDDIxxxK

화학적인 / 포트 / 높은 습도 & 소금 스프레이: BMXDDIxxxKH (컨포멀 코팅)

220VAC contact signals: BMXDAI AC DI

안전 회로, 안전문, safety E-stop: BMXSDI safety DI

Small machines, low I/O count: TM3DI series

Distributed remote IO with scattered field points: STB Advantys remote DI

⚠️ Scope Limitations (What DI modules cannot do)

  1. Cannot directly measure 4-20mA or temperature (AI analog modules required)
  2. Standard DI is not suitable for high-frequency pulse counting (high-speed counter module required)
  3. Safety functions shall not be implemented via ordinary DI; dedicated safety DI modules are mandatory.

이전:

다음:

답장을 남겨주세요

메시지를 남겨주세요