ชุด: Modicon X80 32-point Sourcing Transistor Digital โมดูลเอาท์พุต, Conformal Coated (Severe Environment Version)
Corresponding standard non-coated version: BMXDDO3202K
✅ คำอธิบายรหัสรุ่น
บีเอ็มเอ็กซ์: X80 I/O Series
DDO: Digital Discrete Output
32: 32 ช่อง
02: 24VDC transistor output
เค: Sourcing type (เชิงบวก / Current Source)
ค: การเคลือบตามแบบ (anti-corrosion, ป้องกันความชื้น, dust-proof for severe environments)
📌 ข้อมูลจำเพาะทางไฟฟ้าหลัก
ประเภทเอาต์พุต: Sourcing transistor (พีเอ็นพี, positive logic)
External supply: 24กระแสตรง, range 19~30VDC
จัดอันดับปัจจุบันต่อช่อง: 0.125ก (nominal 0.1A)
Maximum total module current: 3.2ก
Off-state leakage current: ≤0.1mA
On-state voltage drop: <1.5V
Output response time: 1.2นางสาว
Channel parallel connection: Allowed, สูงสุด. 3 channels in parallel
การใช้พลังงาน: 3.6ว
Backplane 3.3V current draw: ประมาณ. 125มิลลิแอมป์
ฉนวนกันความร้อน: 500กระแสตรง, insulation resistance >10MΩ
การป้องกัน: การป้องกันการกลับขั้ว, แรงดันไฟฟ้าเกิน, current limiting; 2A external fast fuse recommended for each group against short circuit
ตัวเชื่อมต่อ: 1 × 40-pin FCN flat cable connector (no built-in terminal block, requires matched FCN40 cable)
🧱 เครื่องกล & ด้านสิ่งแวดล้อม
ขนาด: W32 mm × H100 mm × D86 mm
น้ำหนักสุทธิ: 0.11 กก
ระดับการป้องกัน: IP20 (module only, ติดตู้)
อุณหภูมิในการทำงาน: 0 ~ +60℃ (coated version, suitable for high-humidity, เต็มไปด้วยฝุ่น, salt-spray environments)
MTBF: ประมาณ. 290,000 ชั่วโมง
การรับรอง: ซีอี, แอล, ซีเอสเอ, ยูเคซีเอ, อีเอซี, อาร์ซีเอ็ม, marine classification certification
🤖 PLC Compatibility
Modicon M340 (local rack / X80 remote I/O)
Modicon M580 (local rack / X80 remote I/O, ePAC)
⚠️ Selection Comparison
| แบบอย่าง | การเคลือบผิว | ประเภทเอาต์พุต |
| BMXDDO3202K | มาตรฐาน, no coating | 32 × 24VDC sourcing transistor |
| BMXDDO3202KC | การเคลือบตามแบบ (ค) | 32 × 24VDC sourcing transistor |
🛠️ การใช้งานทั่วไป & หมายเหตุ
- Suitable for driving DC24V indicators, small relays, ขดลวดโซลินอยด์ (observe single-channel current limit)
- Wiring only via 40-core FCN flat cable; incompatible with regular terminal bases directly
- Transistor output cannot drive AC loads, ไม่มีการสัมผัสทางกล, not suitable for high-frequency large inductive loads. Freewheeling diode in reverse parallel is mandatory for inductive loads
- Coated version for water treatment, การทำเหมืองแร่, มารีน, outdoor cabinets and other high-humidity corrosive scenarios
- Matched FCN40 Factory Cables
Cables are fully interchangeable between BMXDDO3202KC and BMXDDO3202K, 40-pin Fujitsu FCN connector
1) Flying-lead type (strip wires directly to cabinet terminals)
BMXFCW303: 3ม, 40-แกนกลาง, pre-stripped colour-coded wires split into 2 กลุ่มของ 20
BMXFCW503: 5ม
BMXFCW1003: 10ม
2) With ABE7 Telefast terminal base (HE10 dual connector, most common for engineering)
One BMXDDO3202KC requires 2 pcs of ABE7 16-point bases
BMXFCC053: 0.5ม
BMXFCC103: 1ม
BMXFCC203: 2ม
BMXFCC303: 3ม
BMXFCC503: 5ม
BMXFCC1003: 10ม
Common ABE7 bases for reference:
ABE7H16C10, ABE7R16S111, ABE7R16T111 (16-point sourcing DC output terminal blocks)
หมายเหตุ: Third-party compatible FCN40 cables (MISUMI, Weidmüller etc.) are available on market. Confirm specs before purchase: Fujitsu FCN-40P male, 0.14มม.², 24ในดีซี
- I/O Address Mapping (M340/M580, ยูนิตี้โปร / EcoStruxure Control Expert)
The module occupies 2 output words (%QW), ทั้งหมด 32 บิต
Channels Q00~Q15 → %QWx.0 ~ %QWx.15 (1st word)
Channels Q16~Q31 → %QW(x+1).0 ~ %QW(x+1).15 (2nd word)
Automatic rack allocation rule:
M340 local rack: Allocated sequentially by slot after CPU; X80 remote I/O racks follow scanner configuration order.
Channel-level diagnostics supported; ลัดวงจร / overload status word can be read in the program.
- Pinout Summary (FCN40 connector, PNP sourcing)
1~20: Q00~Q15 outputs + grouped supply SPS+, SPS-
21~40: Q16~Q31 outputs + grouped supply SPS+, SPS-
Module internally divided into 2 independent supply banks of 16 คนละช่อง. Independent 2A fast fuse per bank recommended. สำหรับโหลดอุปนัย (โซลินอยด์, รีเลย์), connect reverse freewheeling diode (1N4007) across coil terminals.
- รายการตรวจสอบการแก้ไขปัญหา
- RUN LED off
Poor backplane bus contact: Re-seat module, check rack latches; test in alternative slot
Insufficient backplane power; rack power supply undersized
Hardware module damage (coated version less prone to corrosion failure; check backplane first)
- RUN LED ON, channel LEDs do not follow program output
Confirm PNP sourcing wiring: Negative terminal of load to 24V-, output provides +24V
Loss of external SPS supply, ฟิวส์ขาด (failure of half channels usually means fuse blown for that bank)
Wrong program address, forced value or interlock blocking output
- Channel LED ON but load not actuated
On-state voltage drop>1.5V: Short circuit at load, burnt channel; measure channel voltage to GND
กระแสไฟรั่ว: Dim glow at OFF state is inherent transistor leakage (≤0.1mA, common for small indicators)
- Repeated channel fault / burnt channels
Missing freewheeling diode for inductive loads, breakdown by back EMF
Single-channel current over 0.125A; total module current exceeds 3.2A limit
Reverse polarity of external 24V supply, high voltage intrusion
- Special notes for humid/corrosive environments (KC coated version)
Conformal coating protects PCB only; not resistant to condensation or liquid ingress. Cabinet temperature control and dehumidification required
FCN connector pins vulnerable to salt spray oxidation; apply contact protection spray on connectors
- ตัวเลือกการทดแทน (Same-platform / Domestic PLC replacement)
✅ Direct ชไนเดอร์ การเปลี่ยนแพลตฟอร์มเดียวกัน (no program change, no base modification)
Standard non-coated version: BMXDDO3202K (only without conformal coating, พารามิเตอร์ทางไฟฟ้าที่เหมือนกัน)
คำเตือน: Do not replace KC directly with K for humid / salt-spray / mining environments, service life will be drastically reduced
✅ Domestic alternatives (complete PLC replacement, incompatible with X80 backplane, program migration required)
Selection criteria: 32-point 24VDC PNP sourcing transistor output, 0.1ต่อช่อง, with channel diagnostics
ตัวเลือกทั่วไป:
- นวัตกรรม: AM600 series AM600-32DO (พีเอ็นพี, check revision)
- ซินเจ: XD/XG series 32-point DO module
- HCFA: HC-A0/HC-Q series 32-point transistor output
- HollySys: LX series 32DO sourcing module
คำเตือนที่สำคัญ: Domestic modules have no FCN40 port, terminal-block design only. If existing FCN wiring harness is retained, domestic modules cannot be used for direct swap; only Schneider X80 applies.
- Additional Maintenance Notes
Parallel channels allowed: สูงสุด. 3 channels in parallel for higher drive current
เวลาตอบสนอง: 1.2นางสาว, not suitable for high-speed pulse / PWM output
พื้นที่จัดเก็บ: Coated modules resist corrosion, but avoid high temp & humidity for long-term storage; sealed moisture-proof storage recommended
BMXDDO3202KC Full Technical Datasheet (ชไนเดอร์อย่างเป็นทางการ)
ชุด: โมดิคอน X80; พิมพ์: 32-point 24VDC sourcing (พีเอ็นพี) transistor digital output module; C = Conformal Coated Severe Environment Version
- ข้อมูลพื้นฐาน
แบบอย่าง: BMXDDO3202KC
ซีพียูที่เข้ากันได้: Modicon M340 / M580 (local rack, X80 remote I/O station)
จำนวนช่อง: 32 ทำ, split into 2 banks × 16 independent supply domains
ประเภทเอาต์พุต: Solid-state transistor, Positive Sourcing (พีเอ็นพี)
มาตรฐาน: TH/IEC 61131-2
อินเทอร์เฟซ: 40-pin Fujitsu FCN flat cable interface, no built-in terminal block
- Electrical Output Ratings
External supply SPS: ดีซี24วี, 19โวลต์ ~ 30 โวลต์กระแสตรง
Rated continuous current per channel: 0.1ก; ขีด จำกัด ปัจจุบัน: 0.125ก
Max total module output current: 3.2ก
Off-state leakage current: ≤0.1mA
On-state voltage drop: <1.5V
Output response time: 1.2 นางสาว
Parallel channels: Permitted, สูงสุด. 3 channels in parallel
การป้องกันการโอเวอร์โหลด: Built-in current limiting + การเดินทางทางอิเล็กทรอนิกส์, overload range 0.125~0.185A
ป้องกันการลัดวงจร: On-board current limiting, external 2A fast fuse required for each 16-channel bank
การป้องกันแรงดันไฟฟ้าเกิน: Transil transient suppressor diode; reverse protection: reverse diode
ฉนวนกันความร้อน: 500กระแสตรง, insulation resistance>10MΩ
Fault detection threshold: >18V DC = normal; <14V DC = upstream supply fault alarm
การใช้พลังงานโดยทั่วไป: 3.6ว
Backplane 3.3V bus consumption: Typical 125mA
- การวินิจฉัย & ตัวชี้วัด
RUN green: Module healthy
ERR red: โมดูลผิดพลาด / bus fault
Independent green LED per channel: Channel status indication
Channel-level diagnostics supported: ไฟฟ้าลัดวงจร, โอเวอร์โหลด, external supply loss; fault word readable in CE/Unity Pro
- ข้อมูลจำเพาะทางกล
ขนาด: W32 mm × H100 mm × D86 mm
น้ำหนักสุทธิ: 0.11 กก
ระดับการป้องกัน: IP20 (module only, cabinet use)
PCB treatment: การเคลือบตามแบบ (ความชื้น, mould and salt spray resistant)
- การให้คะแนนด้านสิ่งแวดล้อม
อุณหภูมิในการทำงาน: 0 ℃~ +60 ℃
อุณหภูมิในการจัดเก็บ: -40 ℃~ +85 ℃
ความชื้นสัมพัทธ์: 5% ~ 95%, ไม่ควบแน่น (coating does not stop condensation or water ingress)
MTBF: 312,254 ชั่วโมง (อ้างอิง)
การรับรอง: ซีอี, แอล, ซีเอสเอ, ยูเคซีเอ, อีเอซี, อาร์ซีเอ็ม, การรับรองทางทะเล
- Software Address Assignment
Output occupancy: 2 %QW words (QWx, QWx+1), ทั้งหมด 32 บิต
Q0~Q15 → QWx bit0~bit15
Q16~Q31 → QWx+1 bit0~bit15
- Comparison with Non-coated Sibling Model
BMXDDO3202K: Identical electrical specs, no conformal coating, standard indoor environment only
BMXDDO3202KC: Conformal coated, for mining, การบำบัดน้ำ, มารีน, high-humidity salt-spray cabinets
- ข้อจำกัดที่สำคัญ (วิศวกรรมมุ่งเน้น)
- เอาท์พุททรานซิสเตอร์, ไม่มีผู้ติดต่อ, cannot drive AC loads. Freewheeling diode mandatory for inductive loads
- Not designed for high-speed pulse / PWM output
- Two banks of 16 channels with isolated supplies; blown fuse only impacts that bank of 16 คะแนน
- Only compatible with FCN40 cables (BMXFCW/BMXFCC series); direct connection to generic terminals not supported
Schneider Modicon X80 (M340/M580) Digital Output DO Module List
Code definition:
DDO: Solid-state DC transistor output; DRA/DRC: เอาท์พุทรีเลย์; DAO: Triac AC output
K = Sourcing PNP; 12 = Sinking NPN; C = Conformal coating Severe; H = Wide temp + การเคลือบตามแบบ; suffix H = severe environment grade
Interface classification: Direct terminal / FCN flat cable (requires ABE7 terminal base + FCW/FCC cable)
- DC Transistor Output (BMXDDO Series, 24กระแสตรง)
| แบบอย่าง | คะแนน | พิมพ์ | Current per Channel | อินเทอร์เฟซ | หมายเหตุ |
| บีเอ็มเอ็กซ์ดีโอ1602 | 16 | Sourcing PNP | 0.625ก | 20-pin direct terminal | Standard high-current transistor |
| บีเอ็มเอ็กซ์ดีโอ1602H | 16 | Sourcing PNP | 0.625ก | 20-pin direct terminal | Wide temp coated severe -25~70℃ |
| BMXDDO1612 | 16 | Sinking NPN | 0.125ก | 20-pin direct terminal | Standard sinking |
| BMXDDO1612H | 16 | Sinking NPN | 0.125ก | 20-pin direct terminal | Wide temp coated sinking |
| BMXDDO3202K | 32 | Sourcing PNP | 0.125ก | FCN40 flat cable | Standard non-coated base version |
| BMXDDO3202KC | 32 | Sourcing PNP | 0.125ก | FCN40 flat cable | Conformal coated severe (โมเดลเป้าหมายของคุณ) |
| BMXDDO6402K | 64 | Sourcing PNP | 0.125ก | Dual FCN40 flat cable | Standard non-coated 64pt |
| บีเอ็มเอ็กซ์ดีโอ6402KC | 64 | Sourcing PNP | 0.125ก | Dual FCN40 flat cable | Conformal coated 64pt severe |
- เอาท์พุทรีเลย์ (DRA / ดีอาร์ซี, รองรับไฟ AC/DC)
Relays suited for AC220V loads; DRC = fast relay, DRA = standard relay
| BMXDRA0804T | 8 | 100~150VAC | Isolated contacts | Legacy model |
| BMXDRA0805 | 8 | 24กระแสตรง / 24~240VAC | Independent relay | ล้าสมัย, อะไหล่เท่านั้น |
| BMXDRA0805H | 8 | 24กระแสตรง / 24~240VAC | Independent relay | Coated severe |
| BMXDRA0815 | 8 | 24กระแสตรง / 24~240VAC | Independent relay | Regular active model |
| BMXDRA0815H | 8 | 24กระแสตรง / 24~240VAC | Independent relay | Coated severe |
| BMXDRA1605 | 16 | 24กระแสตรง / 24~240VAC | Independent relay | Popular 16pt relay DO |
| BMXDRA1605H | 16 | 24กระแสตรง / 24~240VAC | Independent relay | Coated severe |
| BMXDRC0805 | 8 | 24กระแสตรง / 24~240VAC | High-speed relay | Faster operation |
| BMXDRC0805H | 8 | 24กระแสตรง / 24~240VAC | High-speed relay | ความเร็วสูง + เคลือบ |
- Triac AC Output (DAO, AC loads only)
| แบบอย่าง | คะแนน | เรตติ้ง | หมายเหตุ |
| บีเอ็มเอ็กซ์ดีโอ1605 | 16 | 48~240VAC, 0.5ก | Solid-state AC output, ไม่มีผู้ติดต่อ, for AC lamps, เครื่องทำความร้อน |
| BMXDAO1605H | 16 | 48~240VAC, 0.5ก | Coated severe |
- I/O แบบผสม (DI+DO, common for engineering selection)
| แบบอย่าง | จาก | ทำ | ประเภทเอาต์พุต |
| BMXDDM16025 | 8จาก | 8ทำ | เอาท์พุทรีเลย์ |
| BMXDDM16025H | 8จาก | 8ทำ | รีเลย์, coated version |
| BMXDDM3202K | 16จาก | 16ทำ | 24VDC sourcing transistor, FCN cable |
✅ Quick Selection Cheat Sheet
- Direct terminal (20-เข็มหมุด): บีเอ็มเอ็กซ์ดีโอ1602 / 1612 ชุด, hardwire directly, no FCN cable needed
- FCN flat cable type: 32pt, 64pt (3202เค / เคซี, 6402เค / เคซี), must use BMXFCW/BMXFCC cable + ABE7 terminal block
- Difference between C and H
ค: PCB conformal coating only, temp 0~60℃ (BMXDDO3202KC)
ชม: การเคลือบตามแบบ + wide temperature -25~70℃ (1602ชม,1612ชม, DRAxxH)
- Transistor outputs cannot drive AC; relay and DAO triac support AC loads
คอนแทคเตอร์,เบรกเกอร์,เซ็นเซอร์,ตัวเข้ารหัส,บมจ,ตัวแปลง























NH42-63-318x560.png)



