Schneider NT06H2 Air Circuit Breaker

NT: MasterPact NT series Luftleistungsschalter (ACB, legacy model, eingestellt; replacement model MTZ1 06H2)

06: Rahmengröße 06, frame rated current 630A

H2: Breaking capacity class H2; Icu=50kA@440VAC, short-time withstand current Icw=50kA (1S), Class B selective protection

Elektrische Kernparameter

Wichtige Anmerkungen

1. Auslaufstatus: NT series scheduled for end-of-sale by the end of 2025. Replacement model MTZ1 06H2, part number LV947203 (draw-out version)
2. Parameter Clarification

Ue=690V: Maximum normal operating voltage

Ui=1000V: Spannungsfestigkeit der Netzfrequenz

Uimp=12kV: Blitzimpulse halten der Spannung stand. NOT applicable for 12kV high-voltage switchgear, this is an insulation index for low-voltage ACB

3. Anwendung: Incoming feeder, bus tie and heavy-load outgoing feeder in low-voltage distribution systems, for industrial plants, data centers and marine power distribution; supports selective protection and coordination with upstream/downstream devices
4. Reference Frame Part Numbers

NT06H2 3P Fixed: 47113

NT06H2 3P Draw-out: 47203

NT06H2 4P Fixed: 47119

Zubehör & Ersatzteile

Trip Units: MicroLogic 2.0 / 5.0 / 6.0 / 7.0 (Überlast, kurze Zeitverzögerung, instantaneous and earth-fault protection)

Zubehör: Motor operating mechanism, Hilfskontakte, fault alarm contacts, closing coil, shunt trip coil, Türverriegelung, phase barriers

Draw-out base: Mandatory independent cradle for draw-out version

Richtlinien zur Fehlerbehebung

1. Fehler beim Schließen: Undervoltage coil de-energized, incomplete spring charging, cradle not in connected position, interlock blocking
2. Unintended tripping: Check trip unit protection curve, Erdschluss, harmonic distortion and temperature rise
3. Isolationstest: Power frequency withstand test at Ui=1000V level; 12kV impulse withstand is type-test only, no on-site 12kV impulse test

Inländische alternative Referenz

Domestic MT06H2 (Schneider domestic MT series). Compatible breaking capacity and mounting dimensions for direct replacement.

Schneider MasterPact NT06H2 Air Circuit Breaker Technical Manual (Full Engineering Version, per original datasheet 0613CT0001)

Bemerkungen: NT series is legacy discontinued ACB, frame size NT06, In=630A; breaking class H2; frame supplied without trip unit, MicroLogic trip unit to be ordered separately; standard IEC 60947-2, isolating function, Class B selective protection

Inhaltsverzeichnis

1. Produktübersicht & Erklärung des Modellcodes
2. Bewertete elektrische Parameter
3. Mechanische Parameter, Gesamtabmessungen & Gewicht
4. MicroLogic Trip Unit Selection
5. Zubehörliste & Secondary Terminal Definition
6. Installation & Verkabelungsanforderungen
7. Betrieb, Handling & Interlock Description
8. Wartung, Inspektion & Fehlerbehebung
9. Umgebungsbedingungen
10. Replacement Model Information
11. Original Document Index
12. Produktübersicht & Erklärung des Modellcodes

1.1 Überblick

MasterPact NT series low-voltage air circuit breakers for incoming feeders, bus ties and high-current outgoing feeders in 400/690V low-voltage distribution systems. NT06H2 maximum frame rating 630A, available in draw-out or fixed construction, spring charged operation, configurable with intelligent MicroLogic protection unit, supports remote signalling, metering and communication.

Wichtige Erinnerung: Ui=1000V (Bemessungsisolationsspannung), Uimp=12kV (lightning impulse withstand voltage). NOT 12kV high voltage circuit breaker, only for AC ≤690V low-voltage distribution.

1.2 Modellaufschlüsselung

NT: MasterPact NT series air circuit breaker

06: Rahmengröße 06, frame rated current 630A

H2: Breaking class H2; Icu=50kA@440VAC, Icw=50kA 1s, Class B selective

Teilenummern:

NT06H2 3P Fixed: 47113

NT06H2 3P Draw-out: 47203

NT06H2 4P Fixed: 47119

1.3 Produktstatus

NT series scheduled end-of-sale by end of 2025; replacement model MTZ1 06H2, part number LV947203 (Auszug). Mounting dimensions and secondary interfaces fully compatible for direct replacement.

2. Bewertete elektrische Parameter

3. Mechanische Parameter, Gesamtabmessungen & Gewicht

3.1 Mechanische Ausdauer

Mechanisches Leben: 20,000 Operationen (no-load make/break)

Elektrisches Leben (400V, In): 10,000 Operationen

Spring charging: Manual charging / motor charging MCH optional

3.2 Gesamtabmessungen (3P, Einheit: mm)

Fester Typ: W300 × H415 × D266

Ausziehbarer Typ (with cradle): W300 × H415 × D376

4P version width 360mm, height and depth unchanged

3.3 Gewicht

Fixed frame only: ≈32kg

Draw-out frame + cradle: ≈52kg

3.4 Three positions for draw-out version

1. Verbundene Position: Main circuit and secondary circuit fully connected, normaler Betrieb
2. Test Position: Main circuit disconnected, secondary circuit remains connected for protection test
3. Disconnected Position: Main and secondary circuits fully disconnected, breaker can be withdrawn for maintenance
4. MicroLogic Trip Unit Selection (Must be ordered separately, not included with frame)

Protection setting range: Und (lange Zeit) 0.4~1×In; Isd short-time delay 0.5~10×In, delay 0.1/0.2/0.4s; Ii instantaneous 1~15×In.

5. Zubehörliste & Secondary Terminal Definition

5.1 Optionales Zubehör

1. MCH: Charging motor AC220V / DC24V
2. XF: Closing solenoid AC220V / DC24V
3. MX: Shunt-Auslösespule (remote opening)
4. MN: Unterspannungsauslöser (MNu time-delayed undervoltage for auto-transfer application)
5. OF: Hilfskontakte (CB on/off status feedback)
6. SDE: Fault trip contacts (signal for overload/short-circuit/earth fault trip)
7. PF: Cradle position contacts (verbunden / prüfen / disconnected position)
8. Phase barriers, Schranktürverriegelung, mechanical interlock cables, padlock device
9. ULP communication module: Modbus-RTU, remote signalling & Dosierung

5.2 Secondary Terminal Definition

6. Installation & Verkabelungsanforderungen
7. Montage: Vertikale, aufrechte Installation, ±5° tilt allowed; inverted mounting prohibited
8. Hauptstromkreisanschluss: Frontanschluss / rear horizontal / rear vertical connection; apply specified tightening torque for copper busbars to avoid overheating
9. Secondary control wiring: 0.75~1.5mm² multi-core shielded cable; independent AC220V/DC24V control power supply for secondary circuit
10. Isolationstest: Power frequency withstand test at Ui=1000V level; 12kV impulse withstand is type test only, no on-site 12kV impulse test
11. Draw-out operation: Use dedicated crank for rack-in / rack-out; prohibit racking out breaker from connected position under live condition
12. Betrieb, Handling & Interlock Description

7.1 Operation Procedure

1. Aufladen: Manual charging handle or MCH motor auto charging; charging complete, charged indicator lights on
2. Schließen: Local front panel close pushbutton / XF remote close; verify interlock conditions before closing
3. Öffnung: Local open pushbutton / MX remote opening / automatic protection tripping; after fault trip, fault reset button must be manually reset before re-closing

7.2 Verriegelung (Two-incoming one bus tie scheme)

Mechanische Verriegelung: Steel cable mechanical interlock, physically prevents simultaneous closing of three ACBs

Electrical interlock: Close circuit wired in series with normally closed contacts of other breakers for double protection

Cradle position interlock: Closing circuit blocked when not in connected position, closing prohibited

Fault trip interlock: Auto-transfer closing logic blocked upon SDE contact activation

8. Wartung, Inspektion & Fehlerbehebung

8.1 Regelmäßige Wartung

Semi-annual: Check charging status, on/off indication, contact temperature rise, tightness of secondary wiring

Jährlich: Dust cleaning, insulation inspection, trip unit test (using MicroLogic test cable)

Überholung (jeder 5 Jahre): Disassemble to inspect main contacts and arc chamber, mechanical lubrication, mechanical life verification

8.2 Typische Fehlerbehebung

1. Fehler beim Schließen

Incomplete charging; undervoltage MN coil de-energized; cradle not in connected position; interlock blocked; fault trip not reset

2. Unintended tripping

Verify protection curve; Erdschluss; harmonic overload; loose wiring with overheating; voltage dip triggering MN undervoltage trip

3. Ladefehler

No power supply to MCH motor; jammed charging mechanism; damaged charged-ready contact

4. No fault signal output

Wrong SDE auxiliary contact wiring, verbrannte Kontakte

9. Umgebungsbedingungen

Betriebsumgebungstemperatur: -5℃ ~ +70℃; Über 40℃ ist eine Leistungsreduzierung erforderlich

Lagertemperatur: -40℃ ~ +85℃

Relative Luftfeuchtigkeit: ≤95 % (nicht kondensierend)

Höhe: ≤2000m; derating and insulation correction required above 2000m

Schutzart: Device IP30; IP40 with cabinet door closed

Verschmutzungsgrad: 3

10. Replacement Model Information

NT06H2 → MTZ1 06H2

Rahmen 630A, Icu=50kA, compatible MicroLogic trip unit

Montagemaße, primary busbar and secondary terminals fully compatible, no cabinet modification required for in-panel retrofit

Supports ECOSTRUXURE Power software commissioning, upgraded communication interface

Schneider MasterPact NT Full Series Model List (IEC Version, Discontinued ACB, Frame 630~1600A)

Benennungsregel: NT + Frame Code + Klasse brechen

Frame Code: 06=630A; 08=800A; 10=1000A; 12=1250A; 16=1600A

Klasse brechen: N1 / H1 / H2 / L1; Konstruktion: Behoben / Ausziehbar; Poles 3P/4P; Frame without trip unit, MicroLogic to be ordered separately

Common Base Parameters: Ui=1000V, Uimp=12kV, Ue max AC690V, Class B selective protection

Breaking Class Definition (440V, Icu ultimate breaking capacity)

N1: 35Die

H1: 42Die

H2: 50Die (same class as NT06H2)

L1: 130Die (strombegrenzender Typ, application for high short-circuit capacity)

NT Full Model List

Draw-out part number: add 10 to the last digit. Example NT06H2 3P Draw-out:47203; 4P fixed part number +6 (NT06H2 4P Fixed 47119)

Derivative Isolator Models (HA version)

NTxxHA: Isolator (without trip unit, IEC60947-3)

NT06HA / NT08HA / NT10HA / NT12HA / NT16HA

Compatible Trip Unit List (Universal for full NT series)

MicroLogic 2.0: Long-time overload only

MicroLogic 5.0A: Long-time + kurze Zeitverzögerung + augenblicklich (preferred for incoming / Buskrawatte)

MicroLogic 6.0A: 5.0A + Erdschlussschutz

MicroLogic 7.0A: 6.0A + Fehlerstromschutz + harmonic measurement

Replacement Cross Reference Table (NT → MTZ1)

Selection Remarks

1. NT series fully discontinued, not recommended for new projects; MTZ1 can be used for spare parts replacement for existing projects with compatible primary and secondary interfaces.
2. L1 current-limiting type for systems with extremely high short-circuit current, höhere Kosten; H2 is preferred for normal incoming feeder and bus tie.
3. Rated current can be derated within the same frame by changing current sensor inserts, z.B. NT06 frame available with 400A/500A/630A sensors.