Nom et prénom: GX-series EtherCAT IO-Link Master Unit (IP67 Field Type)
Positionnement de base: Bus EtherCAT, 8-channel IO-Link master, M12 A-coding female connector. Anti-poussière et étanche, can be mounted directly on equipment frames or production lines without installation inside control cabinets.
✅ Spécifications clés
Number of ports: 8 IO-Link ports (M12 A-coding female)
Bus interface: EtherCAT (IN/OUT M12, supports daisy-chain connection)
Version IO-Link: V1.1.2
Débit en bauds: COM1 (4.8k) / COM2 (38.4k) / COM3 (230.4k) auto-adaptatif
Power supply per port: DC24V, maximum. 200mA per port, with independent short-circuit protection
SIO compatible mode: Switchable to PNP DI / PNP DO
DEPUIS: ON ≥15V, OFF ≤5V; multi-stage filter time optional (défaut d'usine: 1MS)
FAIRE: Sortie push-pull, 0.3Un par canal
Power supply range: DC20.4~26.4V (24V ±10%/-15%)
Classe de protection: IP67 (suitable for dusty and humid field environments)
Logiciel de configuration: Sysmac Studio, CX-ConfiguratorFDT
Compatible PLC: NX/NJ/NY series EtherCAT controllers
✅ Main Features
- IP67 field mounting, saves junction boxes, adopts M12 Smartclick quick connectors
- 8 independent IO-Link master ports. Each port can connect IO-Link sensors, îlots de vannes, analog modules, RFID and other smart slaves
- Flexible port mode switching: IO-Link smart mode / SIO digital DI / SIO digital DO
- EtherCAT daisy-chain, simple networking. Diagnostic information (sensor temperature, signal quality, event alarms) can be uploaded to PLC
- Supports automatic upload, download and backup of IO-Link device parameters. No manual setting required after sensor replacement
✅ Similar Series & Référence alternative
GX-ILM04C: 4-port version (same architecture IP67 EtherCAT IO-Link master)
NX-ILM08C: NX backplane type (monté sur armoire, non-IP67), ne confondez pas
✅ Scénarios d'application typiques
Lignes d'assemblage, machines d'emballage, machines-outils, material handling lines, for mass connection of IO-Link photoelectric sensors, proximity sensors, capteurs de pression, flow sensors, proportional valves and IO-Link hubs.
✅ Notes
EtherCAT cables shall be CAT5e or higher grade shielded STP cable;
SIO DO is PNP push-pull output, cannot directly drive heavy loads;
All ports share 24V power supply, with independent short-circuit protection for each port.
GX‑ILM08C’s core advantages: IP67 field-side installation, EtherCAT daisy-chain, 8-channel IO‑Link, ports compatible with ordinary DI/DO. It is designed for outside control cabinets, dusty and humid production lines, and differentiated from NX‑ILM08C (IP20 for cabinet installation).
- Applications industrielles typiques
- Automotive component assembly lines, montages d'outillage, postes de travail robotisés
Connected to IO-Link proximity sensors, capteurs photoélectriques, cylinder magnetic switches, capteurs de pression, proportional valves, fixture in-place sensors.
Avantages: Modules can be mounted beside tooling without routing cables back to cabinet junction boxes; sensor temperature, signal margin and offset data can be read for predictive maintenance. Parameters can be downloaded automatically during fixture changeover to shorten product change time.
- Machines d'emballage (flow wrappers, emballeurs de caisses, palettiseurs)
For photoelectric detection, material level, pression, web guiding sensors and IO-Link valve islands. IP67 rating fits oily and humid conditions. Ordinary PNP sensors can be used in SIO mode, friendly for retrofitting projects mixing old and new sensors.
- Material handling lines, lignes de tri, entrepôts automatisés, AGV stations
Détection de position, code-reading trigger and photoelectric sensors for belt conveyors, roller lines and transfer units. Long-distance segmented EtherCAT daisy-chain wiring. Rupture de fil, short circuit and sensor disconnection alarms are sent to PLC for fast fault location and reduced downtime.
- Machines-outils, stamping and injection molding equipment
Peripheral detection of machine tools, barrières immatérielles de sécurité, mold confirmation, mold pressure, cooling circuit flow and temperature. Resists cutting fluid and dust. Sensor degradation data can be collected for early warning to avoid defective batches.
- Nourriture & pharmaceutical production lines (wash-down environments)
IP67 protection and M12 quick connectors for wash applications. Connected to sanitary IO-Link flow, temperature and level sensors. Supports sensor ID verification to prevent wrong installation.
- Batterie au lithium & photovoltaic equipment (injection de liquide, lamination, tri)
Centralized access of large numbers of small-point smart sensors. Sensor parameters can be backed up and restored with one click; no on-site commissioning required when replacing sensors in batches. Status data can be uploaded to SCADA for OEE analysis.
- Functional Use Cases
Capteur condition visualization & maintenance prédictive: Monitor photoelectric received light intensity, sensor temperature, vibration and pressure, set threshold alarms before total failure.
Production line retrofitting: Expand I/O points locally on site without adding new control cabinets. Legacy sensors use SIO DI/DO while new smart sensors run IO-Link.
Flexible multi-product production lines: Automatic parameter download for product changeover, automatic sensor identification and anti-mismatch function.
Distributed I/O architecture: Multiple scattered acquisition points on one line connected via EtherCAT chain, reducing heavy multi-core cables.
III. Scénarios inappropriés
Cabinet internal installation with compact backplane requirement: choose NX‑ILM08C
High corrosion or continuous immersion conditions (only IP67, not for long-term submersion)
High-current loads per channel (maximum. 0.3A for DO ports)
- Matching Configuration
Contrôleur: NX/NJ/NY series EtherCAT PLC; Logiciel: Sysmac Studio; Réseautage: Multiple GX modules daisy-chained with STP shielded EtherCAT cables.
OMRON GX-series IO-Link Master Units
✅ GX series only has one official IO-Link master model: GX-ILM08C. GX-ILM04C does not exist; the 4-port field IO-Link master does not belong to the GX series.
| Modèle | Ports | Protection | Bus | Interface | Description |
| GX-ILM08C | 8 IO-Link | IP67 | EtherCAT | M12 A-coding female (IO-Link); M12 D-coding (EtherCAT IN/OUT) | Field distributed I/O, M12 quick connect, port switchable SIO DI/DO, compatible with NX/NJ/NY EtherCAT controllers |
Confusable IO-Link Masters from Related Families (Not GX series)
| Modèle | Série | Ports | Protection | Bus | Construction |
| NX-ILM400 | NX | 4 | IP20 | EtherCAT | Cabinet backplane mounting, borne à vis, for indoor cabinet use |
| NXR-ILM08C-ECT | NXR | 8 | IP67 | EtherCAT | Rugged remote terminal, similar form factor to GX |
| NXR-ILM08C-EIT | NXR | 8 | IP67 | EtherNet/IP | EtherNet/IP version, not EtherCAT |
Additional GX-series EtherCAT Remote I/O Modules (Not IO-Link Masters)
GX is Omron’s large IP67 EtherCAT remote I/O family. Besides IO-Link master, it includes digital and analog modules:
GX-ID16□2 / OD16□2 / MD16□2: 3-tier terminal digital I/O
GX-□D16□1 / OC1601: 2-tier terminal digital I/O
GX-□D16□8 / □D32□8: e-CON connector digital I/O
GX-AD0471 / DA0271: Entrée analogique / sortie analogique
GX-EC0211 / EC0241: EtherCAT junction / branch units
GX-JC03 / JC06: Extension connectors
Contacteur,disjoncteur,capteur,Encodeur,API,Convertisseur





















NH42-63-318x560.png)



