성명: Frequency/Voltage/Current (10 kHz Version)
KFU8 series DIN rail signal conditioning module, designed for frequency/speed acquisition from encoders and pulse 감지기에스, converting pulse signals into standard analog signals, with an optional frequency-divided pulse output.
구별:
KFU8-FSSP-1.D-Y = 10 kHz maximum input frequency
KFU8-FSSP-1.D-Y322444 = 40 kHz high-speed version
Many suppliers mix these two models; confirm the frequency limit during selection.
✅ 핵심 기능
- Two measurement modes: 빈도 (헤르츠) / 회전 속도 (rpm)
주파수 범위: 0.001 헤르츠 ~ 9999 헤르츠
Speed range: 0.02 rpm ~ 9999 rpm
- Configurable analog output (selectable via menu):
0…10V / 2…10V
0…20 mA / 4…20 mA
- Frequency-divided pulse output: division ratio 1~9999, isolated pulse signal for PLC or secondary instruments
- 내장 24 V DC auxiliary sensor power supply; compatible with 2/3/4-wire proximity switches and NPN/PNP incremental encoders
- 4-digit red LED display; shows input Hz/rpm or output V/mA. 4-button local programming with one-touch Teach-In calibration
- Period measurement method, optimized for low-speed pulse signals
📌 Electrical Specifications
전원공급장치: 24 DC에서
소비전력: <5 W
Max input frequency: 10 kHz (이 모델); minimum pulse width ≥40 μs
정확성: ≤0.2% FS
Processing response: 5 ms internal update; display refresh adjustable from 0.01~2.5 s (no impact on signal conversion)
격리: Galvanic isolation between input and analog output
보호 등급: IP20 (캐비닛 장착 전용)
설치: Snap-on 35 mm DIN 레일
터미널: Removable coded terminals, wire cross-section 0.2~2.5 mm²
작동 온도: -25 ℃ ~ +40 ℃ (비응축)
보관온도: -40 ℃~+85 ℃
📋 Terminal Assignment
| 단말기 | 신호 |
| 1 | Sensor GND |
| 2 | 펄스 출력 |
| 5 | 아날로그 출력 + |
| 6 | 아날로그 출력 – (전압) |
| 4 | 아날로그 출력 – (현재의) |
| 7 | 감지기 24 V+ |
| 11 | Power Supply L+ 24 DC에서 |
| 12 | Power Supply L- 0 다섯 |
| 14 | NPN/PNP Input – (Cathode) |
| 15 | NPN/PNP Input + (양극) |
| 13 | Sensor GND |
| Remaining terminals | NC (Not Connected) |
⚙️ Factory Default Parameters
방법: rpm (회전 속도)
Pulse per revolution (PPR): 1
Full Scale Range: 9999
아날로그 출력: 0…10V
Display Refresh Time: 0.33 에스
Division Ratio: 1
매개변수 저장: Long-press Enter + + to store into EEPROM (power-down retention)
🛠 일반적인 응용 프로그램
Speed measurement for conveyors, 팬, pumps and roller tables
Converting pulse signals from flowmeters into 4–20 mA analog signals for DCS/PLC
Encoder signal division, local speed display + analog transmission
Stable measurement of low-frequency pulse signals (period measurement outperforms frequency counting at low speeds)
⚠️ 문제 해결 가이드
| 잘못 | 가능한 원인 & 구제책 |
| 전원 없음, 디스플레이 없음 | 1. 확인하다 24 V DC at terminals 11/12; 2. 느슨한 단자; 3. Reverse polarity protection activated |
| Signal present but reading always zero | 1. NPN/PNP wiring reversed; 2. Pulse width ≥40 μs; 3. 아니요 24 V on sensor supply terminal 7; 4. Wrong measurement mode (rpm/Hz) |
| 변동하는 판독값 | 1. Increase display refresh time; 2. 단일 종단 접지가 있는 차폐 케이블을 사용하십시오.; 3. Check voltage drop on encoder supply; 4. Ensure high level ≥16 V DC, low level ≤6 V DC |
| Analog output stuck | 1. Match current/voltage output type with AI card; 2. Max load resistance ≤600 Ω for current output; 3. Re-run Teach-In calibration |
| Display overflow | 1. Actual speed exceeds set RANGE; 2. Incorrect PPR setting (value too large) |
| No pulse output on terminal 2 | 1. Division ratio ≠ 1; 2. Open-collector output requires external pull-up resistor on PLC side; 3. Input frequency below lower limit |
| Self-test error Err on power-up | EEPROM checksum failure; power cycle first; repeated error means hardware failure, replace the module |
| Poor low-speed accuracy | This module uses period measurement; ensure pulse width ≥40 μs; avoid ultra-narrow pulses |
📎 Cross-model & 교체 옵션
같은 시리즈: KFU8-FSSP-1.D-Y322444 (40 kHz, for high-speed encoders)

국내 대안: CZJ, UBE frequency/speed isolators (must support period measurement + frequency-divided pulse output)
- 배선 지침 (KFU8-FSSP-1.D-Y)
Full Terminal List
| 단말기 | Signal Definition | 메모 |
| 1 | Sensor GND | Spare sensor ground |
| 2 | Frequency-divided Pulse Output | Isolated pulse for PLC high-speed counter |
| 4 | Current Output I- | Negative terminal for 4…20 mA |
| 5 | Analog U+/I+ | Common positive for voltage & 전류 출력 |
| 6 | Voltage Output U- | Negative terminal for 0…10 V |
| 7 | 감지기 24 V+ | Encoder/proximity sensor supply, 최대. 30 엄마 |
| 8 | NAMUR Input – | NAMUR sensor channel |
| 9 | NAMUR Input + | NAMUR sensor channel |
| 11 | Module Power L+ 24 DC에서 | Main power positive |
| 12 | Module Power L- 0 다섯 | Main power negative |
| 13 | Sensor GND | Sensor power ground |
| 14 | NPN/PNP Input – (Cathode) | Pulse negative |
| 15 | NPN/PNP Input + (양극) | Pulse positive |
| 기타 | NC | Do not connect |
Standard Wiring Schemes
- 3-wire PNP Encoder (가장 일반적인)
Brown wire → Terminal 7 (24 V+)
Blue wire → Terminal 13 (접지)
Black signal wire → Terminal 15; 단말기 14 shorted to 13 (접지)
- 3-wire NPN Encoder
브라운 → 7; 블루 → 13
Black signal → 14; 단말기 15 shorted to 7 (24 V+)
- 4–20 mA analog to DCS AI card
단말기 5 → AI+; 단말기 4 → AI-
- 0…10 V voltage output
단말기 5 → AI+; 단말기 6 → AI-
- Frequency-divided pulse output
단말기 2 to PLC high-speed counter; fit external pull-up resistor on PLC side
중요 공지: Max sensor supply current = 30 엄마; do not drive multiple encoders. Use shielded cable for long-distance pulse wiring, ground the shield only at one end.
- Button Operation & 매개변수 설정
4 front-panel keys: 방법 (메뉴), ◀, +, Enter
- 전원 켜기; wait for self-test then enter measurement display (Hz/rpm)
- Short press Mode to switch menu items; ◀ = shift digit; + = change value
- 매개변수 저장: Long press Enter + + together to write into EEPROM (정전 후에도 유지됨)
- Exit menu: Long press Mode to return to measurement screen
Menu Items (English Original)
- 방법: Measurement Mode
rpm = Rotational Speed (Encoder application recommended)
Hz = Frequency (Pulse flowmeter)
- PULSE: Pulses Per Revolution (PPR)
예: 1000-line encoder → set PULSE=1000
- RANGE: Full Scale Value
예: 0~1500 rpm → set RANGE=1500
- 밖으로: 출력 유형
0-10다섯 / 2-10다섯 / 0-20엄마 / 4-20엄마
- DIV: Division Ratio (1~9999)
Output pulse = Input pulse ÷ DIV; set DIV=1 if no division required
- DISP: Display Refresh Time (0.01~2.5 s)
Increase to 0.5~1 s to stabilize low-speed readings; 세트 0.1 s for high speed
- TEACH: One-touch Calibration (Teach-In)
Run equipment to full-scale speed, enter TEACH and press Enter; auto-set upper range (zero point fixed at 0)
공장 기본값: MODE=rpm, PULSE=1, RANGE=9999, OUT=0…10V, DIV=1, DISP=0.33 s
Factory Reset Procedure
전원 켜기, hold Mode + Enter for 5 seconds until FACT appears; confirm to restore all factory settings. All custom parameters will be erased.
- 오류 문제 해결 표
| 징후 | 문제 해결 단계 |
| 전원을 켠 후 표시되지 않음 | 1. 측정하다 24 V DC between terminals 11 & 12; 2. Check loose terminals; 3. Reverse polarity protection triggered |
| 읽지 않음, display stays zero | 1. Verify NPN/PNP wiring polarity; 2. Ensure pulse width ≥40 μs; 3. 확인하다 24 V output on terminal 7; 4. Confirm correct MODE (rpm/Hz) |
| 불안정한, flickering readings | 1. Increase DISP refresh time; 2. Shield cable single-end grounded; 3. Check voltage drop on encoder supply; 4. High level ≥16 V DC, low level ≤6 V DC |
| Analog output locked and unchanged | 1. Match OUT type with AI card (current/voltage cannot be mixed); 2. Current output load resistance ≤600 Ω; 3. Re-run TEACH calibration |
| Display over-range overflow | 1. Actual speed exceeds RANGE setting; 2. PPR value set too high |
| No pulse output on terminal 2 | 1. DIV ratio not equal to 1; 2. Open-collector output requires external power/pull-up resistor on PLC; 3. Input frequency below lower limit |
| Err code on power-up self-test | EEPROM data error; restart first; repeated error = hardware damage, 모듈 교체 |
| Inaccurate low-speed measurement | This module uses period measurement (good for low speed); ensure pulse width ≥40 μs, avoid ultra-narrow pulses |
- Parameter Table (Chinese ↔ English, Exportable)
| Chinese Parameter | English Tag | 범위 | 비고 |
| 测量模式 | 방법 | rpm / 헤르츠 | 속도 / 빈도 |
| 每转脉冲数 | PULSE | 1~9999 | Encoder PPR value |
| 满量程 | RANGE | 1~9999 | Corresponds to full-scale analog output |
| 输出类型 | 밖으로 | 0-10다섯,2-10다섯,0-20엄마,4-20엄마 | Analog signal selection |
| 分频系数 | DIV | 1~9999 | Pulse output division |
| 显示刷新时间 | DISP | 0.01~2.5 s | Only affects display, no impact on conversion speed |
| 一键标定 | TEACH | — | Dynamic full-scale calibration |
| 精度 | 정확성 | ≤0.2%FS | Full-scale accuracy |
| 最大输入频率 | Fmax | 10 kHz | For model Y only (not Y322444) |
- 시운전 절차 (On-site Sequence)
- Wire with power disconnected; double-check power, encoder and analog terminals
- 전원 켜기; 확인하다 24 V DC on sensor supply terminal 7
- Set MODE, PPR, RANGE and OUT type
- Rotate the encoder and confirm reading follows actual speed
- Measure analog output with multimeter, verify zero and full-scale values
- If pulse division is needed: connect PLC high-speed counter and test terminal 2 pulse signal
- Save parameters and record settings; commissioning complete
Pepperl+Fuchs KFU8 Series DIN Rail Signal Converter Order List
설명: KFU8 = K-System local-display programmable signal conditioners; divided into standard type and Ex intrinsically safe barrier type.
Suffix rules:
1.D = 1-channel; 2.D = 2-channel
Y = 10 kHz input; Y322444 = 40 kHz (only for FSSP models)
Ex = Intrinsically safe for hazardous area Zone 0/1/2
| Order Part Number | 제품명 | Brief Function | 폭발 방지 |
| KFU8-FSSP-1.D-Y | Frequency/Speed Converter (10 kHz) | Encoder pulse → analog 0-10V/4-20mA, with frequency-divided pulse output & 로컬 디스플레이 | 아니요 |
| KFU8-FSSP-1.D-Y322444 | Frequency/Speed Converter (40 kHz) | Same as FSSP, 최대 40 kHz for high-speed encoders | 아니요 |
| KFU8-DW-1.D | Speed Monitor | Overspeed/underspeed monitoring with relay alarm output; 최대 40 kHz, period measurement | 아니요 |
| KFU8-UFC-1.D | Frequency Converter with Limit Alarms | 1 mHz~10 kHz; NAMUR/dry contact input; 4-20엄마 + 계전기 + 트랜지스터 출력; SIL2 | 아니요 |
| KFU8-UFC-1.D.FA | 주파수 변환기 (이전 버전) | 레거시 모델; phase-out, replace with UFC-1.D | 아니요 |
| KFU8-UFC-Ex1.D | Intrinsically Safe Frequency Barrier | 지금부터, 존 0/1/2, NAMUR 입력, SIL2 | 예 (지금부터) |
| KFU8-UFT-2.D | Dual-channel Frequency/Slip/Speed Direction Monitor | Dual NAMUR/dry contact input; detect rotation direction, slip and synchronous deviation; 비슷한 물건 + 릴레이 출력 | 아니요 |
| KFU8-UFT-Ex2.D | Explosion-proof Dual-channel Direction/Slip Barrier | Hazardous area dual-channel rotation monitoring | 예 (지금부터) |
| KFU8-USC-1.D | Universal Voltage/Current Signal Converter | 격리 & scaling for 0/4-20mA & 0-10V analog signals; with limit relay alarm | 아니요 |
| KFU8-GUT-Ex1.D | Intrinsically Safe Universal Temperature Transmitter | RTD/Thermocouple input, dual relay alarm, SIL2 | 예 (지금부터) |
모델 코딩 규칙
KFU8 [기능 코드] [채널].[버전] [-접미사]
FSSP: Frequency Speed → Speed transmission with divided pulse output
DW: Speed Watch → Speed monitoring & 경보
UFC: Universal Frequency Converter → Frequency conversion + limit alarm
UFT: Universal Frequency Twin → Dual-channel frequency, 방향 & slip monitoring
USC: Universal Signal Converter → Standard analog signal isolation
GUT: Universal Temperature → Temperature signal transmission
전: Intrinsically safe explosion-proof barrier
1.D = Single channel; 2.D = Dual channel
Y = 10 kHz; Y322444 = 40 kHz (FSSP exclusive suffix)
KFU8 Series Common Accessories
K-CJC-EX: Cold-junction compensation terminal (for GUT temperature modules)
KF-ST-5BU / KF-ST-5GN: Removable coded terminals (blue/grey)
Power Rail: K-series power bus for multi-module parallel power supply
빠른 선택 가이드
- Speed transmission + divided pulse output → FSSP (와이 / Y322444)
- Overspeed/underspeed alarm (no divided pulse) → DW-1.D
- NAMUR proximity switch frequency input + alarm → UFC / UFC-Ex
- Dual encoders, slip & rotation direction detection → UFT-2.D / UFT-Ex2.D
- Analog 4-20mA/0-10V isolation, 스케일링 & alarm → USC-1.D
- RTD/TC temperature measurement in hazardous area → GUT-Ex1.D
보충 노트
All KFU8 modules: 40 mm 폭, 35 mm DIN 레일 마운트, 4-자리 표시 + 4-button programming; different from non-display KFD0 / KFA5 barriers.
전원공급장치: Most models support 20~90 V DC / 48~253 V AC; FSSP model only supports 24 DC에서.
수명 종료 알림: UFC-1.D.FA is obsolete; select UFC-1.D for new projects.
접촉기,회로 차단기,감지기,인코더,PLC,변환기
















NH42-63-318x560.png)



